Dryer Parts
Start With Your Model Number
Find Parts Fast
Guaranteed Fit
Repair Videos
Need help finding your model number?
Popular Dryer Parts
$2.70
In Stock
Door Catch Kit
Fix Number FIX334230
Manufacturer Part Number 279570
This kit includes two door strikes, and three door catches, to service doors that have one or two catches. The strike is mounted on the body of the dryer, while the catch is mounted on the dryer door. These two parts work together to keep the dryer door shut while in operation. If your appliances lid will not close, or it will not start, it may be time to replace the door catch. If this part is malfunctioning, it should be replaced immediately, as it is not safe to run a dryer with the door not properly closed. This kit also comes with a set of instructions to help with the repair.
Fixes these symptoms
- Door Pops Open
- Door won’t close
- Lid or door won’t close
- See more...
Installation Instructions
jeffrey from Brookhaven, PA
Dryer would run, but not heat
Needed it running quick, so no diagnostics. Ordered one of everything that could fix problem (plus a new door catch). Tipped it onto it's back & popped the bottom cover off. Element, thermal cutoff, thermistor, and fuse. were right in front and held by 2 screws each (don't drop them, don't ask). A little bit tight inside, but no big issue. vacuumed the inside, replaced everything (it was the Heating Element, by the way), slapped the cover on, and put it back in its spot. works like it was new. Yes, I unplugged it first. Remember! Safety Third!
Read more...
$18.58
In Stock
Drum Bearing Slide - White
Fix Number FIX755842
Manufacturer Part Number WE1M504
This single drum bearing slide attaches to the outer-most side of the bearing. This part is also sometimes referred to as a drum slide, drum glide, or drum pad. It provides support to the front of the drum as it rotates. They are approximately 3-inches long, 1 inch wide and made from a durable white plastic. If your appliance starts making unusual sounds, is not drying clothes properly, or leaves marks on clothes, it may be time to replace this part. The dryer has 2 slides, which we recommend replacing at the same time, as they tend to wear out at the same rate. You will need to order 2 of this part to replace both drum bearing slides, since it is sold individually. Before you begin this repair, be sure to disconnect the power to the dryer.
Fixes these symptoms
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
Donald L. from Belmont, MA
Dark marks on clothing; clothing sticking between drum and front panel
Others with the same problem of dark marks on clothing suggested replacing the white and the grey drum slides that slip into the front drum bearing unit. When I open up the dryer, I did find that both the white and grey drum slides on one side of the front drum bearing piece had completely worn away, and some of the drum bearing piece was also worn away. I had decided in advance to order both white slides, both grey slides, a new felt seal, and the front drum bearing piece. Possibly I could have reused the old front drum bearing, but the replacement was cheap enough. Three bits of advice: 1) if you replace the felt seal, make sure you get it tucked behind the clips on the door panel; 2) if you replace the front drum bearing piece, once you have the dryer put back together, reach up and pull the plastic drum bearing toward you to be sure it is fully snapped into place; 3) after you replace the slides or felt, the drum will make mild rubbing noises as it turns, so run the dryer with no heat for about 30 minutes to seat the parts.
Read more...
$17.19
In Stock
Multi Rib Belt - 92-1/4"
Fix Number FIX346995
Manufacturer Part Number 341241
This multi rib belt is an OEM replacement part for a dryer. It attaches to the drum, idler pulley, and motor pulley, and is responsible for spinning the drum. Over time, the belt can become frayed, brittle, and inflexible. If you can hear the motor running, but the drum does not turn, it is likely that the belt is broken. Other symptoms of a broken multi rib belt include unusual noises, failing to start, no heat, a burning smell, and an unresponsive touchpad. Depending on the model, you will find the belt by looking behind the front panel or under the main top of the dryer. This belt is 1/4-inches wide, has a length of 92-1/4-inches, and has four ridges and three groves on the belt. Each belt is sold separately.
Fixes these symptoms
- Drum Not Spinning
- Heat stays on after drum has stopped
- Noisy
- See more...
$31.29
In Stock
BELT DRIVE
Fix Number FIX16542496
Manufacturer Part Number WE03X29897
This 89.5-inch drive belt is for dryers. It has a 4-rib design on the inside for a better grip. If comparing the size of your current belt to the new one, keep in mind that a small amount of stretching and contortion will occur over time, and this belt will fit despite small inaccuracies. You will find this part wrapped all the way around the dryer drum, around a tension pulley, and around the drive motor pulley. This allows the parts to work together to spin the drum as the motor rotates. A common symptom of a broken drive belt is a drum that will not turn. This part is prone to wear and tear over time and will likely stretch or become brittle, leading to complete breakage of the part. The drum cannot spin without a drive belt, so it needs to be replaced immediately. For this repair, we recommend wearing work gloves to protect your hands from sharp edges, disconnect the power, remove the main panel, and access the motor drive to secure the new belt in place.
Fixes these symptoms
- Drum Not Spinning
- Noisy
- See more...
Installation Instructions
Nae from BRENTWOOD, TN
The dry was making a whining sound. Very loud.
I followed all the video on the website with all the parts I had purchased. Very easy. Just make sure you unplug the dryer first. Thank you,
Read more...
$14.29
In Stock
Drum Bearing Slide - Green
Fix Number FIX6447706
Manufacturer Part Number WE1M1067
This single drum bearing slide is an OEM approved replacement part for dryers. It can also be known as a bearing drum slide, pad, or glide. The slides attach to the inner most slots on the front bearing. As the dryer rotates, the drum bearing slides help to support the front of the drum. If your appliance becomes noisy, is not drying properly, or leaves marks on clothes, it may be time to replace it. If you are replacing one slide, we recommend replacing the other slide at the same time, as they deteriorate at a similar rate. You will need to order 2 of these parts as there are 2 in each dryer. It is approximately 2.6-inches deep, 0.06-inches in height, and 0.5-inches wide. This part is denoted as being green in the title, however users and technicians have noted it is actually gray in color.
Fixes these symptoms
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
Donald L. from Belmont, MA
Dark marks on clothing; clothing sticking between drum and front panel
Others with the same problem of dark marks on clothing suggested replacing the white and the grey drum slides that slip into the front drum bearing unit. When I open up the dryer, I did find that both the white and grey drum slides on one side of the front drum bearing piece had completely worn away, and some of the drum bearing piece was also worn away. I had decided in advance to order both white slides, both grey slides, a new felt seal, and the front drum bearing piece. Possibly I could have reused the old front drum bearing, but the replacement was cheap enough. Three bits of advice: 1) if you replace the felt seal, make sure you get it tucked behind the clips on the door panel; 2) if you replace the front drum bearing piece, once you have the dryer put back together, reach up and pull the plastic drum bearing toward you to be sure it is fully snapped into place; 3) after you replace the slides or felt, the drum will make mild rubbing noises as it turns, so run the dryer with no heat for about 30 minutes to seat the parts.
Read more...
$19.63
In Stock
Dryer Thermal Fuse
Fix Number FIX11741460
Manufacturer Part Number WP3392519
The dryer thermal fuse, also sometimes referred to as the thermal cut off or temperature fuse, is a 2 by 1/2-inch, white, plastic safety mechanism that halts the flow of electricity to the motor circuit when a dryer overheats. If the fuse is missing or broken, your dryer will not start. A thermal fuse fails when the exhaust temperature exceeds the fuse rating, that is when the temperature rises above the temperature that the fuse is intended to manage. This can be caused by the heating element shorting, a regulating thermostat or thermistor failure, or with a partially restricted exhaust vent. The fuse attaches to the blower wheel housing. It must be replaced when there is no longer continuity between the terminals. This is a one-time fuse, meaning it cannot be re-set. The replacement part features two 3/16-inch terminals. While performing this repair, we recommend checking to make sure all vents are cleared and vacuumed. This OEM part is sold individually.
Fixes these symptoms
- Heat stays on after drum has stopped
- Not Heating
- Too hot
- See more...
Installation Instructions
gary from apex, NC
dryer not heating
Checked the heating element and found a break in the heating coil. Decided to change the thermal fuse and the the cycling thermostat because of the age of the dryer.
Read more...
$13.42
In Stock
Roller Support Tri-Ring
Fix Number FIX11755850
Manufacturer Part Number WPW10512946
This small but mighty OEM piece is called a tri-ring and is used to support the drum roller shaft and the idler pulley shaft in your dryer. It helps to provide a tight seal between components by evenly distributing pressure. The part is triangular in shape, and less than an inch in size. Overtime it can become brittle or compressed, which can lead to a noisy tumbling cycle, or your dryer not tumbling at all. The tri-ring itself is simple to replace, simply slip off the damaged one and slip on the new. However, to access the drum roller or idler pulley, you will need to remove the front panel and drum of your dryer. This may require tools like a Phillips screwdriver, a quarter inch nut driver, putty knife, a small flat blade screwdriver, and a pair of needle nose pliers depending on your model. Ensure that the power is disconnected before beginning your repair.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
JAMES from GREENSBURG, PA
Loud squeaking and squealing
Lint Filter - Removed old lint filter and inserted new lint filter. This is the first time I tried to fix a dryer. A handyman I am not. I found two very useful YouTube videos using basically my model of Kenmore (11067851600). Disassembly/Assembly - here is a difference between Kenmore 29" wide dryers and 27" wide dryers. Mine is 27". My effort was not a smooth as these videos. The bottom front panel's right most clip was quite troublesome. The moisture sensor wire required needle nose pliers to be disconnected and reconnected. The open door sensor was not easy to disconnect. Although with a few special magic words it came apart. The upper front panel was held in place with two T20 Torx screws. I had only had a T15 driver, therefore a trip to Home Depot was required. The first two tri rings were not easily removed, however, on third tri ring it became easier and not damaged. Replacement of tri rings was not troublesome. Support rollers snapped in place easily. However, I did thoroughly clean the housing. It was quite grimy. Actually, while I had the dryer open I cleaned everything including the heating element and electric motor. It now operates quietly. It took me a little over two hours because I am not handy and must take care not to make matters worse plus I thoroughly cleaned everything include scuff marks where the drum rubs. Anyone else probably should have it completed 30-60 minutes easily.
Read more...
$14.37
In Stock
Rear Drum Support Roller Kit
Step 2: removed screws from lent catcher.
Step 3: removed top lid.
Step 4: removed front panel.
Step 5: removed drum.
Step 6: removed plastic washers.
Step 7: removed old wheels.
Step 8: installed new wheels.
Reversed steps to put everything back. Read more...
Fix Number FIX347627
Manufacturer Part Number 349241T
This is a rear drum support roller kit for your dryer. The 2 rollers come with 4 tri-rings, and 1 palnut. We recommend that you replace both rollers at once. This kit stabilizes the drum cylinder, while letting the drum rotate on the support rollers. If you are having problems with your appliance during tumble mode, or if it is too noisy, you will need this kit. To complete this repair you will need a putty knife, Philips screwdriver and a 5/16 nut driver.
Fixes these symptoms
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
Tyrik from KENNESAW, GA
The roller support wheels were worn down and needed replacing.
Step 1: removed power source.Step 2: removed screws from lent catcher.
Step 3: removed top lid.
Step 4: removed front panel.
Step 5: removed drum.
Step 6: removed plastic washers.
Step 7: removed old wheels.
Step 8: installed new wheels.
Reversed steps to put everything back. Read more...
$124.64
In Stock
Drive Motor with Pulley
Fix Number FIX334304
Manufacturer Part Number 279827
This motor fits most Whirlpool incorporated dryer brands before 1996. NOTE: Pulley is NOT available separately.
Fixes these symptoms
- Noisy
- Will Not Start
- Won't Start
- See more...
Installation Instructions
Mike from NORRISTOWN, PA
Motor would overheat and shut off in the middle of the cycle.
Replaced the drive motor using the installation video listed with the part. The instructions were accurate and very easy to follow.
Read more...
$17.64
In Stock
Idler Pulley Assembly
Fix Number FIX11743765
Manufacturer Part Number WP691366
The idler pulley is found in your dryer and provides tension to the belt in order to rotate the drum. If your clothes are taking a long time to dry, the machine is noisy while operating, or the dryer will not start or tumble, there may be an issue with the idler pulley assembly. To replace this part, you will need to lift the top and remove the front panel of the dryer. You will want to take note of how the drum belt is positioned so it can be put back in place once the new idler pulley is in place. While you have the appliance opened up and accessible, you may want to consider replacing the drum belt at this time.
Fixes these symptoms
- Noisy
- See more...
Brands
- Admiral Dryer Parts
- Amana Dryer Parts
- Bosch Dryer Parts
- Crosley Dryer Parts
- Electrolux Dryer Parts
- Estate Dryer Parts
- Frigidaire Dryer Parts
- General Electric Dryer Parts
- Gibson Dryer Parts
- Haier Dryer Parts
- Hoover Dryer Parts
- Hotpoint Dryer Parts
- Inglis Dryer Parts
- International Dryer Parts
- Jenn-Air Dryer Parts
- Kelvinator Dryer Parts
- Kenmore Dryer Parts
- KitchenAid Dryer Parts
- LG Dryer Parts
- Magic Chef Dryer Parts
- Maytag Dryer Parts
- Norge Dryer Parts
- Roper Dryer Parts
- Samsung Dryer Parts
- Speed Queen Dryer Parts
- Tappan Dryer Parts
- Uni Dryer Parts
- Westinghouse Dryer Parts
- Whirlpool Dryer Parts
Related Pages
- Dryer Bearings
- Dryer Belts
- Dryer Brackets and Flanges
- Dryer Caps and Lids
- Dryer Circuit Boards and Touch Pads
- Dryer Doors
- Dryer Drawers and Glides
- Dryer Drums and Tubs
- Dryer Ducts and Vents
- Dryer Elements and Burners
- Dryer Fans and Blowers
- Dryer Filters
- Dryer Fuses
- Dryer Handles
- Dryer Handles and Latches
- Dryer Hardware
- Dryer Hinges
- Dryer Hoses and Tubes
- Dryer Igniters
- Dryer Knobs
- Dryer Latches
- Dryer Legs and Feet
- Dryer Lights and Bulbs
- Dryer Motors
- Dryer Panels
- Dryer Pulleys
- Dryer Pumps
- Dryer Racks
- Dryer Seals and Gaskets
- Dryer Sensors
- Dryer Springs and Shock Absorbers
- Dryer Switches
- Dryer Thermostats
- Dryer Timers
- Dryer Trays and Shelves
- Dryer Trim
- Dryer Valves
- Dryer Wheels and Rollers
- Dryer Wire Plugs and Connectors
Popular Dryer Models
- MDE5500AYW Residential
- DBVH512EF0WW Electric
- HTDX100EM8WW ELECTRIC DRYER
- WED4815EW1 ELECTRIC DRYER
- GTDP180ED0WW
- PYE2300AYW Residential
- GLER341AS2 Residential
- GTDP490ED0WS
- DCVH515EF0WW Electric
- GTD42EASJ2WW DRYER
- GTD33EASK0WW ELECTRIC DRYER
- MEDC215EW1 ELECTRIC DRYER
- MEDX655DW1 ELECTRIC DRYER
- GEW9250PW1 Residential
- NED4655EW1 ELECTRIC DRYER
- MDG5500AWW Residential
- GLEQ2152ES0 Residential
- DBXR463ED2WW Electric
- FEQ332ES0 Residential
- WED9200SQ0 Residential