Roper Dryer Parts

Roper Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular Roper Dryer Parts

$16.60
  In Stock
Multi Rib Belt - 92-1/4"
★★★★★
★★★★★
(16)
Fix Number FIX346995
Manufacturer Part Number 341241
This multi rib belt is an OEM replacement part for a dryer. It attaches to the drum, idler pulley, and motor pulley, and is responsible for spinning the drum. Over time, the belt can become frayed, brittle, and inflexible. If you can hear the motor running, but the drum does not turn, it is likely that the belt is broken. Other symptoms of a broken multi rib belt include unusual noises, failing to start, no heat, a burning smell, and an unresponsive touchpad. Depending on the model, you will find the belt by looking behind the front panel or under the main top of the dryer. This belt is 1/4-inches wide, has a length of 92-1/4-inches, and has four ridges and three groves on the belt. Each belt is sold separately.
Fixes these symptoms
  • Heat stays on after drum has stopped
  • No heat or not enough heat
  • Noisy
  • See more...
Installation Instructions
carolyn from phila, PA
not spinning
follow the vidio Read more...
$20.88
  In Stock
Dryer Thermal Fuse
★★★★★
★★★★★
(15)
Fix Number FIX11741460
Manufacturer Part Number WP3392519
The dryer thermal fuse, also sometimes referred to as the thermal cut off or temperature fuse, is a 2 by 1/2-inch, white, plastic safety mechanism that halts the flow of electricity to the motor circuit when a dryer overheats. If the fuse is missing or broken, your dryer will not start. A thermal fuse fails when the exhaust temperature exceeds the fuse rating, that is when the temperature rises above the temperature that the fuse is intended to manage. This can be caused by the heating element shorting, a regulating thermostat or thermistor failure, or with a partially restricted exhaust vent. The fuse attaches to the blower wheel housing. It must be replaced when there is no longer continuity between the terminals. This is a one-time fuse, meaning it cannot be re-set. The replacement part features two 3/16-inch terminals. While performing this repair, we recommend checking to make sure all vents are cleared and vacuumed. This OEM part is sold individually.
Fixes these symptoms
  • Heat stays on after drum has stopped
  • No heat or not enough heat
  • Shuts off too soon
  • See more...
Installation Instructions
gary from apex, NC
dryer not heating
Checked the heating element and found a break in the heating coil. Decided to change the thermal fuse and the the cycling thermostat because of the age of the dryer. Read more...
$6.32
  In Stock
Door Catch Kit
★★★★★
★★★★★
(10)
Fix Number FIX334230
Manufacturer Part Number 279570
This kit includes two door strikes, and three door catches, to service doors that have one or two catches. The strike is mounted on the body of the dryer, while the catch is mounted on the dryer door. These two parts work together to keep the dryer door shut while in operation. If your appliances lid will not close, or it will not start, it may be time to replace the door catch. If this part is malfunctioning, it should be replaced immediately, as it is not safe to run a dryer with the door not properly closed. This kit also comes with a set of instructions to help with the repair.
Fixes these symptoms
  • Door won’t close
  • Lid or door won’t close
  • No heat or not enough heat
  • See more...
Installation Instructions
jeffrey from Brookhaven, PA
Dryer would run, but not heat
Needed it running quick, so no diagnostics. Ordered one of everything that could fix problem (plus a new door catch). Tipped it onto it's back & popped the bottom cover off. Element, thermal cutoff, thermistor, and fuse. were right in front and held by 2 screws each (don't drop them, don't ask). A little bit tight inside, but no big issue. vacuumed the inside, replaced everything (it was the Heating Element, by the way), slapped the cover on, and put it back in its spot. works like it was new. Yes, I unplugged it first. Remember! Safety Third! Read more...
$30.72
  In Stock
M Series New Style Coil Kit
★★★★★
★★★★★
(1)
Fix Number FIX334310
Manufacturer Part Number 279834
This OEM kit comes with two ignition coils (one three-terminal boost/hold coil, and one two-terminal secondary coil). Usually only one of them burns out, but you should replace them as a set as both have to be operational for the gas valve to open. The primary purpose of the part is to open the gas valve and allow the gas to enter the burner. This is a safety mechanism to make sure that there is never an unsafe buildup of gas inside the appliance. You will find the coils attached to the dryer gas valve. This is not an uncommon repair; it can fail due to normal material fatigue over time. To test your current parts, watch the burner, and if the igniter glows for a while and then shuts off without the gas is igniting, it usually means one of these coils is bad.
Fixes these symptoms
  • No heat or not enough heat
  • Noisy
  • Shuts off too soon
  • See more...
Installation Instructions
Dennis from ALISO VIEJO, CA
Dryer ran but did not dry clothing.
Best site I have ever used for repairs. First a list of what parts were needed was provided right from the start, no guessing. I followed all of the video's provided for installation instructions and and that was it. Very easy to make repairs and almost rebuilt my dated dryer to like new condition. Appliance was in very good physical condition just needed new components to bring it back. Highly recommend this site to anyone who can turn a wrench. Read more...
$34.04
  In Stock
Dryer Cycling Thermostat
★★★★★
★★★★★
(8)
Fix Number FIX11741405
Manufacturer Part Number WP3387134
This thermostat is an OEM replacement part for a dryer. It is sold individually. It measures approximately 2-inches by 1.5-inches, is black and silver, and constructed of plastic and metal material. You will find this part attached to the blower wheel housing. Cycling thermostats continually cycle the heating element off and on to maintain a constant inner temperature inside the dryer. This particular cycling thermostat will turn the heating element off once the temperature reaches 155F and cycles back on once the internal temperature drops by 25F. Do not forget to unplug the power to the dryer before you begin this repair. Keep in mind that you will need to pull the dryer out from the wall because this repair will need to be done from the back of the appliance with the back panel removed.
Fixes these symptoms
  • Heat stays on after drum has stopped
  • No heat or not enough heat
  • Shuts off too soon
  • See more...
Installation Instructions
gary from apex, NC
dryer not heating
Checked the heating element and found a break in the heating coil. Decided to change the thermal fuse and the the cycling thermostat because of the age of the dryer. Read more...
$22.12
  In Stock
Rear Drum Support Roller Kit
★★★★★
★★★★★
(3)
Fix Number FIX347627
Manufacturer Part Number 349241T
This is a rear drum support roller kit for your dryer. The 2 rollers come with 4 tri-rings, and 1 palnut. We recommend that you replace both rollers at once. This kit stabilizes the drum cylinder, while letting the drum rotate on the support rollers. If you are having problems with your appliance during tumble mode, or if it is too noisy, you will need this kit. To complete this repair you will need a putty knife, Philips screwdriver and a 5/16 nut driver.
Fixes these symptoms
  • Marks left on clothes
  • Noisy
  • Takes too long to dry
  • See more...
Installation Instructions
Tyrik from KENNESAW, GA
The roller support wheels were worn down and needed replacing.
Step 1: removed power source.
Step 2: removed screws from lent catcher.
Step 3: removed top lid.
Step 4: removed front panel.
Step 5: removed drum.
Step 6: removed plastic washers.
Step 7: removed old wheels.
Step 8: installed new wheels.
Reversed steps to put everything back.
Read more...
$61.74
  In Stock
Heating Element - 240V 5400W
★★★★★
★★★★★
(8)
Fix Number FIX334313
Manufacturer Part Number 279838
Sourced directly from the manufacturer, this heating element is an OEM approved replacement part for a variety of dryers and is sold individually. It measures approximately 10.5 inches long, 7.5 inches wide and 2 inches deep. The heating element is the primary source of heat used to dry the clothes in your dryer. This heating element is strung with a coiled wire made of a nickel and chrome alloy. It may need to be replaced if your dryer does not produce heat, if it produces too much heat, or if it will not turn on. If your dryer does not heat, first check for a blown thermal fuse on the blower housing before replacing the heating element. In most cases, the heating element will have a break in the element, making it defective. For this repair you will need a quarter inch nut driver and a pair of needle nose pliers. Start this repair by disconnecting the power and then remove the dryer vent. This repair is done from the back of the appliance with the back panel removed. With the panel removed, this will give you access to the heater element. Your next step is to remove the high-limit thermostat from the housing and remove the two wires from the heater terminals. Now remove the screws securing the element to the housing and slide the element out. Installation of the new part is done in the reverse order.
Fixes these symptoms
  • Heat stays on after drum has stopped
  • No heat or not enough heat
  • Shuts off too soon
  • See more...
Installation Instructions
gary from apex, NC
dryer not heating
Checked the heating element and found a break in the heating coil. Decided to change the thermal fuse and the the cycling thermostat because of the age of the dryer. Read more...
$13.44
  In Stock
Roller Support Tri-Ring
Fix Number FIX11755850
Manufacturer Part Number WPW10512946
This small but mighty OEM piece is called a tri-ring and is used to support the drum roller shaft and the idler pulley shaft in your dryer. It helps to provide a tight seal between components by evenly distributing pressure. The part is triangular in shape, and less than an inch in size. Overtime it can become brittle or compressed, which can lead to a noisy tumbling cycle, or your dryer not tumbling at all. The tri-ring itself is simple to replace, simply slip off the damaged one and slip on the new. However, to access the drum roller or idler pulley, you will need to remove the front panel and drum of your dryer. This may require tools like a Phillips screwdriver, a quarter inch nut driver, putty knife, a small flat blade screwdriver, and a pair of needle nose pliers depending on your model. Ensure that the power is disconnected before beginning your repair.
Fixes these symptoms
Installation Instructions
JAMES from GREENSBURG, PA
Loud squeaking and squealing
Lint Filter - Removed old lint filter and inserted new lint filter. This is the first time I tried to fix a dryer. A handyman I am not. I found two very useful YouTube videos using basically my model of Kenmore (11067851600). Disassembly/Assembly - here is a difference between Kenmore 29" wide dryers and 27" wide dryers. Mine is 27". My effort was not a smooth as these videos. The bottom front panel's right most clip was quite troublesome. The moisture sensor wire required needle nose pliers to be disconnected and reconnected. The open door sensor was not easy to disconnect. Although with a few special magic words it came apart. The upper front panel was held in place with two T20 Torx screws. I had only had a T15 driver, therefore a trip to Home Depot was required. The first two tri rings were not easily removed, however, on third tri ring it became easier and not damaged. Replacement of tri rings was not troublesome. Support rollers snapped in place easily. However, I did thoroughly clean the housing. It was quite grimy. Actually, while I had the dryer open I cleaned everything including the heating element and electric motor. It now operates quietly. It took me a little over two hours because I am not handy and must take care not to make matters worse plus I thoroughly cleaned everything include scuff marks where the drum rubs. Anyone else probably should have it completed 30-60 minutes easily. Read more...
$40.60
  In Stock
Igniter Kit
★★★★★
★★★★★
(1)
Fix Number FIX334180
Manufacturer Part Number 279311
This is a genuine OEM replacement igniter kit for your gas-heated clothes dryer. The silicon carbide igniter is used to light the gas that creates the heat in order to dry your clothes. If your dryer is not heating, takes a long time to dry clothes, or has low heat you may want to consider replacing your igniter. This kit can be used to replace both round and flat igniters, and comes with a 3-inch flat igniter, bracket, 4-inch wire lead, and the plug. Before beginning this repair, please ensure that the power and gas is disconnected from the range. As the igniter is located within the burner assembly, you will need a variety of tools to complete the installation. These tools include a putty knife, a small flat blade screwdriver, a 5/16 nut driver, and a 5/16 socket with a ratchet. This part should be handled with care, as the igniter is very fragile.
Fixes these symptoms
  • No heat or not enough heat
  • Takes too long to dry
  • Will Not Start
  • See more...
Installation Instructions
Joe from Red Bank, NJ
The coil kit was malfunctioning. Difficult to fully diagnosis as the problem.
The coil kit showed the correct numbers and it worked intermittently. However, when replaced everything worked OK. I also replaced the igniter, however, I do not believed it was a problem. However, I left in the new igniter. Read more...
$18.32
  In Stock
Idler Pulley Assembly
★★★★★
★★★★★
(1)
Fix Number FIX11743765
Manufacturer Part Number WP691366
The idler pulley is found in your dryer and provides tension to the belt in order to rotate the drum. If your clothes are taking a long time to dry, the machine is noisy while operating, or the dryer will not start or tumble, there may be an issue with the idler pulley assembly. To replace this part, you will need to lift the top and remove the front panel of the dryer. You will want to take note of how the drum belt is positioned so it can be put back in place once the new idler pulley is in place. While you have the appliance opened up and accessible, you may want to consider replacing the drum belt at this time.
Fixes these symptoms
  • Noisy
  • Takes too long to dry
  • Will Not Start
  • See more...
Installation Instructions
carolyn from phila, PA
not spinning
follow the vidio Read more...

Appliance Type

Related Pages

Popular Roper Dryer Models