Roper Parts

★★★★★

★★★★★

1 Review

Fix Number

FIX11750107

Manufacturer Part Number

WPW10196405

This chrome drip bowl is an OEM approved replacement part sourced directly from the manufacturer. Drip bowls are a part for your cooktop, positioned underneath the burner to catch spills. This drip bowl fits under 8-inch burner elements and has a diameter of approximately 10-inches. It is common for the manufacturer to switch up designs, so it may not match your current part, however searching using the correct model number will ensure proper fit and function. Drips bowls are prone to wear and tear and can be a fire hazard if not replaced when needed. It is also a quick, easy, and cheap way to give your appliance a fresh new look. Each drip bowl is sold individually, so if you are interested in replacing your other drips bowls, they need to be ordered separately. This is also an opportune time to inspect the terminals for corrosion or damage, and the condition of the burner. No tools are required for installation, simply line up the hole on the bowl with the terminal block and drop it into place. Give your new drip bowl a regular cleaning with warm water and soap to help it last as long as possible.

★★★★★

★★★★★

3 Reviews

Fix Number

FIX11739091

Manufacturer Part Number

WP2187172

This door bin is sold individually. Its dimensions are 18 inches wide, 4.5 inches high, by 7 inches deep.

★★★★★

★★★★★

10 Reviews

Fix Number

FIX334313

Manufacturer Part Number

279838

Sourced directly from the manufacturer, this heating element is an OEM approved replacement part for a variety of dryers and is sold individually. It measures approximately 10.5 inches long, 7.5 inches wide and 2 inches deep. The heating element is the primary source of heat used to dry the clothes in your dryer. This heating element is strung with a coiled wire made of a nickel and chrome alloy. It may need to be replaced if your dryer does not produce heat, if it produces too much heat, or if it will not turn on. If your dryer does not heat, first check for a blown thermal fuse on the blower housing before replacing the heating element. In most cases, the heating element will have a break in the element, making it defective. For this repair you will need a quarter inch nut driver and a pair of needle nose pliers. Start this repair by disconnecting the power and then remove the dryer vent. This repair is done from the back of the appliance with the back panel removed. With the panel removed, this will give you access to the heater element. Your next step is to remove the high-limit thermostat from the housing and remove the two wires from the heater terminals. Now remove the screws securing the element to the housing and slide the element out. Installation of the new part is done in the reverse order.

★★★★★

★★★★★

10 Reviews

Fix Number

FIX373087

Manufacturer Part Number

4392065

This is an authentic drum support roller kit for 29-inch-wide dryers. It includes 1 belt, 2 roller wheels and an idler pulley. The parts in this kit allow the dryer to tumble properly by supporting the drum cylinder. The idler pulley provides the tension needed for a multi-ribbed belt. The belt attaches to the drum, idler pulley, and motor pulley. If these parts are damaged, it could cause loud noises such as squeaking and squealing while the drum is turning. These are normal wear parts and are best replaced as a kit to ensure optimal performance.

★★★★★

★★★★★

11 Reviews

Fix Number

FIX11741701

Manufacturer Part Number

WP3406107

This OEM dryer door switch is an on/off mechanism that detects when the door is open to prevent the dryer from operating. If your dryer will turn on but will not start or continues working while the door is open, you may have a faulty door switch. This part features the switch and three wires, is white in color, and measures 6.5 inches long. This switch replaces the two-wire switch that is on many models. You will find this part attached to the inside of the top end of the front panel. One end attaches to the wiring harness and the other goes through the panel to make contact with the door when the door is closed. This is a regular wear part due to such frequent use or continuous harsh handling. Depending on how the switch broke, it might make it impossible to start or stop your drying cycle. You can test the function of this part by pushing on the black tab that sticks out of the front panel to make contact with the dryer door. If there is no resistance in the tab and it does not make a clicking sound, it likely needs to be replaced.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX11746591

Manufacturer Part Number

WP8565925

This is a single rack track stop clip used to prevent the upper dish rack from sliding all the way out of the dishwasher. It is made of gray plastic and can wear with time. This is an easy repair that should not take very long to complete. Start by opening the dishwasher door, depress the tabs to remove both the front stop clips and remove the upper dish rack from the appliance. Now, using your small flat head screwdriver, release the retaining tab to remove the rear stop track that you are replacing, and pull the clip up to remove it. Install the new clip by inserting it into the support rail from the top and press it down to secure it in place.

★★★★★

★★★★★

8 Reviews

Fix Number

FIX11741405

Manufacturer Part Number

WP3387134

This thermostat is an OEM replacement part for a dryer. It is sold individually. It measures approximately 2-inches by 1.5-inches, is black and silver, and constructed of plastic and metal material. You will find this part attached to the blower wheel housing. Cycling thermostats continually cycle the heating element off and on to maintain a constant inner temperature inside the dryer. This particular cycling thermostat will turn the heating element off once the temperature reaches 155F and cycles back on once the internal temperature drops by 25F. Do not forget to unplug the power to the dryer before you begin this repair. Keep in mind that you will need to pull the dryer out from the wall because this repair will need to be done from the back of the appliance with the back panel removed.

★★★★★

★★★★★

3 Reviews

Fix Number

FIX2376034

Manufacturer Part Number

8206232A

To access the exterior lightbulb, the bottom panel of the microwave will need to be removed. It is secured in place with screws, so will require a Philips screwdriver to remove it. Screw the new light bulb directly into the light socket. If this is the first time you have replaced this light bulb, the old light bulb might be held in place with silicone. This silicone will need to be cut off using either a utility knife or dental floss before removing the light bulb. Once this silicone and old bulb has been removed, the replacement bulb can be screwed in its place.

★★★★★

★★★★★

11 Reviews

Fix Number

FIX11739119

Manufacturer Part Number

WP2188656

This is a genuine OEM replacement crisper drawer for refrigerators. It is sold as an individual part. The crisper drawer with humidity control allows you to adjust the humidity within the crisper, which can help preserve the quality of your produce. It attaches to the inner part of the refrigerator to the bottom of the crisper shelf. If your crisper drawer is missing, cracked, damaged, or discolored, it needs to be replaced. It is made of durable clear plastic with a white handle and is sold individually. No tools are needed for installation, simply slide the new crisper drawer into the tracks.

★★★★★

★★★★★

20 Reviews

Fix Number

FIX346995

Manufacturer Part Number

341241

This multi rib belt is an OEM replacement part for a dryer. It attaches to the drum, idler pulley, and motor pulley, and is responsible for spinning the drum. Over time, the belt can become frayed, brittle, and inflexible. If you can hear the motor running, but the drum does not turn, it is likely that the belt is broken. Other symptoms of a broken multi rib belt include unusual noises, failing to start, no heat, a burning smell, and an unresponsive touchpad. Depending on the model, you will find the belt by looking behind the front panel or under the main top of the dryer. This belt is 1/4-inches wide, has a length of 92-1/4-inches, and has four ridges and three groves on the belt. Each belt is sold separately.