Tiller Parts

Nut Lock

$6.15

Fix Number: FIX16381792
Manufacturer Part Number: 596040501

This is a Manufacturer Approved replacement nut for lawn and garden equipment. This item is Metal an is Sold Individually. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt.

Clevis Pin

$5.93

Fix Number: FIX9009427
Manufacturer Part Number: 532132673

This is a genuine component which is specially designed for use with Poulan, Husqvarna, Weed Eater and Jonsered tillers. It is supplied directly from the original equipment manufacturer. This item provides a high-quality replacement for a missing or a faulty hardware that was installed on a new unit. The clevis pin is installed in order to protect your tiller. If the auger gets jammed or clogged, the pin is designed to snap at a certain point of pressure, so it will not damage any other part of the unit. Please make sure to refer to the appropriate diagrams of your model for the correct application of this part. Keep in mind this high-quality clevis pin is made of durable metal and is sold individually. Replacing it is a simple task that should only require pliers to remove the old and secure the new.

Vent Tube

$6.15

Fix Number: FIX16535460
Manufacturer Part Number: V471001201

The purpose of the vent tube is to allow air in to the fuel tank so that a vacuum is not created when the fuel is being fed through the fuel line. Most of the time the Vent line is connected to a fuel line grommet that is installed on the fuel tank. The fuel return line and the fuel line are also connected to the fuel line grommet. The other way a fuel tank is vented in other engines is by use of a fuel cap with a air vent built into it.

Watch the install video

Tiller Forward Drive Belt

$22.17

Fix Number: FIX10035467
Manufacturer Part Number: 954-04090

Genuine Manufacturer Sourced replacement part used on Walk-Behind Push Mowers. This is the Belt which connects to the Transmission and allows mower to mower forward. This part is made out of Rubber and it is Sold Individually. Clean the pulleys off before installing the new belt to ensure top performance and longevity with your new belt. Inspect belts periodically and replace them when worn to maintain peak performance.

Ext. Control Cable, Forward (1

$44.40

Fix Number: FIX16723234
Manufacturer Part Number: A203120

This forward control cable, compatible with various tiller models, enables forward movement when pulled by the user, engaging the forward gear. Measuring 1440mm (approximately 57 inches) in length, this control cable is equipped with a protective sheath to guard against external damage. It is an OEM part and is sold independently, without any additional securing hardware or parts. If your tiller control cable displays extensive wear, fraying, corrosion, or fails to engage the tiller correctly, it is essential to replace it promptly for optimal tiller functionality. To replace the control cable, you will need a wrench and/or screwdriver. Begin by turning off the tiller and locating the control cable near the handle. Disengage it by unscrewing and disconnecting it from the handle. Follow the cable to the engine transmission, typically held on a clip, and disconnect it. Install the new cable to the tiller handle and the engine transmission, ensuring it engages the transmission when pulled from the handle, and then test for functionality.

Fixes these symptoms

Drive system does not work
See more...

Installation Instructions

Terry from LEXINGTON, OK

The metal keepers broke at the top of both cables.

Took cover off behind engine, used pliers to unhook springs off back of transmission, used pliers to slide keepers in forward and backward levers. Read more...

SPARK PLUG 4 CYCL

$4.45

Fix Number: FIX19298356
Manufacturer Part Number: 794-00082

Nut-flglk 5/16-18

$6.15

Fix Number: FIX9092936
Manufacturer Part Number: 712-04063

This nut is fit for lawn and garden equipment and is used to resist loosening when properly threaded onto a bolt. The nut is sold individually. The diameter of the nut is 5/16 inches and the thread size is 18. Refer to the manual provided by the manufacturer for repair instructions.

Installation Instructions

Ronald from SPEARFISH, SD

Replace sheave plate and side skid shoes on snowblower.

Remove eight bolts and two skid shoes and bottom sheave plate. Replace in reverse order.
Most important, get the correct OEM parts from FIX.com. Refer to product parts list in model instruction manual.
Do that first and you too can see how easy this repair is and save big bucks charged by retail repair shop! Read more...

Watch the install video

Belt-v Rev Drv 3

$21.01

Fix Number: FIX10035469
Manufacturer Part Number: 954-04091

This is a Genuine OEM Sourced replacement part used on Walk-Behind Push Mowers and RotoTillers. This is the Belt which connects to the Transmission and allows mower to drive reverse. This part is made out of Rubber and it is Sold Individually. Clean the pulleys off before installing the new belt to ensure top performance and longevity with your new belt. Inspect belts periodically and replace them when worn to maintain peak performance. To replace this belt you would need a Wrench and a Screwdriver.

Lawn Mower Ground Drive Belt

$27.77

Fix Number: FIX9172714
Manufacturer Part Number: 954-04032B

This is a drive belt and it is used on various outdoor lawn equipment. This part is made of rubber and is sold individually. It measures to be 35.80 inches by 0.5 inches. This part drives the transmission, which propels the wheels on your machine. Pro tip, clean off the pulleys before installing this part for a longer lifespan. We recommend inspecting your belt periodically as they wear out quickly, depending on usage.

Fuel Filter

$7.32

Fix Number: FIX9908731
Manufacturer Part Number: 17672-Z0H-003

This is a genuinely sourced fuel filter for a small engine, sold individually. This is an in-tank fuel filter that serves to filter out debris that could potentially be delivered to the engine. Over time it will get clogged, and this will prevent fuel from getting to the engine, hindering its performance. The fuel filter should be inspected once a year or every one-hundred hours. To inspect or replace the fuel filter, start by ensuring the oil filter cap is securely in place. Take off the fuel tank cap, drain the fuel, pull out the old fuel filter through the fuel filler neck (hooking the black fuel tube with wire/paper clip). If the fuel filter is excessively dirty, it will need to be replaced.

Popular Tiller Parts

Installation Instructions

Installation Instructions

Tiller Brands

Related Tiller Parts

Popular Tiller Models

Tiller Parts

Start With Your Model Number

Popular Tiller Parts

Installation Instructions

Installation Instructions

Tiller Brands

Related Tiller Parts

Popular Tiller Models