OEM Murray Parts & Accessories

Bearing

$6.21

Fix Number: FIX9006914
Manufacturer Part Number: 532009040

This is a premium-quality OEM front wheel flange bearing (sometimes called bushing) commonly used in riding lawn mowers. They are used to keep the wheel held in place securely. It is sold individually but two are needed for each front wheel. It is recommended that they be replaced at the same time. Install this part with the flat side facing the grease zerk in the rear side of the wheel.

Bow Tie Cotter Pin

$3.99

Fix Number: FIX9096195
Manufacturer Part Number: 714-04040

This bow tie cotter pin fits snow blowers, as well as other gardening tools. The pin helps secure the auger to the shaft on a snow blower. Due to constant wear, this is a commonly replaced part. Tip: Extra pins are recommended. *Please note: this part is sold individually. For installation instructions, refer to the diagram provided by the manufacturer.

Lawn Tractor Mandrel Assembly

$48.56

★★★★★

1 Review

Fix Number: FIX12087499
Manufacturer Part Number: 587819701

Installation Instructions

Terrence from LORENA, TX

Blade mandrel replacement

1. Remove mower deck.
2. Remove mower blade from defective mandrel.
3. Clean caked up grass from underside of mower deck.
4. Remove belt pulley from top of defective mandrel.
5. Remove four bolts fastening defective mandrel to deck. Note: bolts will most likely shear - make sure you have new ones.
6. Install new mandrel to deck using four new self-tapping bolts.
7. Reinstall mower blade to new mandrel assembly.
8. Reinstall belt pulley to new mandrel assembly.
9. Reinstall mower deck to tractor. Read more...

Cap Axle Black 1 50 x 1 00

$3.99

Fix Number: FIX9007667
Manufacturer Part Number: 532104757

This is an OEM axle cap for lawn tractors and is sold individually. It stops debris from getting into the wheel hub and axle. This axle cap is prone to wear and tear and should be replaced when it is goes missing or appears damaged. No tools are necessary for this easy repair, simply locate the cap axle on the rim of the wheel and remove.

Ring Klip Number T5304-75

$3.99

Fix Number: FIX9143890
Manufacturer Part Number: 812000029

This manufacturer-approved ring clip is found in various lawn and garden equipment models. A ring clip is used as a fastener that secures components or assemblies onto a shaft or housing (such as part of a mower wheel or steering assembly). When it is installed, the part that is visible acts as a shoulder, holding the specific component or assembly together. This very small metal ring clip (approximately 1-inch by 1-inch) is sold individually.

Element- Air Cleaner

$7.06

★★★★★

2 Reviews

Fix Number: FIX9903219
Manufacturer Part Number: 17211-ZL8-023

To ensure your engine is protected, it is vital that the air filter is inspected regularly and replaced according to the manufacturer recommendations. This filter helps to prevent dirt and dust from making its way into the carburetor and damaging the engine. If the engine is not functioning as it should, this should be one of the first parts you check. To inspect the filter, you will need to remove the air cleaner cover, and lift the filter out of place to remove.

Installation Instructions

michael from pikeville, KY

none

i watched how i took off the old parts... Read more...

Plug-Spark

$4.99

Fix Number: FIX9140427
Manufacturer Part Number: 796112S

This is a spark plug and it is found in various lawn equipment. If your engine is not starting or running poorly, you may need to replace the spark plug. This part is a RJ9LM. Meaning, it is a resistor type with a 14mm shell design, 3/8-inch reach, and 13/16-inch hex. The heat range is 9 for automotive, small engine, and ordnance applications. The LM indicates 14mm (special for lawn mowers). Before making this installation make sure to drain fuel from the tank and remove the old spark plug.

Fixes these symptoms

Will Not Start
See more...

Nut, Flange Lock, 5/16-18, Grf

$3.99

Fix Number: FIX9092936
Manufacturer Part Number: 712-04063

This nut is fit for lawn and garden equipment and is used to resist loosening when properly threaded onto a bolt. The nut is sold individually. The diameter of the nut is 5/16 inches and the thread size is 18. Refer to the manual provided by the manufacturer for repair instructions.

Installation Instructions

Ronald from SPEARFISH, SD

Replace sheave plate and side skid shoes on snowblower.

Remove eight bolts and two skid shoes and bottom sheave plate. Replace in reverse order.
Most important, get the correct OEM parts from FIX.com. Refer to product parts list in model instruction manual.
Do that first and you too can see how easy this repair is and save big bucks charged by retail repair shop! Read more...