Whirlpool Parts
Start With Your Model Number
Find Parts Fast
Guaranteed Fit
Repair Videos
Need help finding your model number?

Popular Whirlpool Parts
$7.51
In Stock
Light Bulb - 40W
Fix Number FIX884734
Manufacturer Part Number 8009
This is a genuine OEM 40-Watt replacement light bulb that is compatible with various types of appliances. It has a frosted glass bulb with a standard metal socket base, making it easy to screw and unscrew by hand to replace. It is designed to tolerate extreme temperatures, which is why it is commonly used to light the inside of refrigerators and ovens. Depending on the appliance and location of the bulb, disconnecting the power is recommended. This bulb is sold individually.
Installation Instructions
Helen from Quincy, MA
lightbulb in refrigerator went out
Removed plastic shield on top of refrigerator. Removed old bulb.. Replaced new bulb. Reinstalled plastic shield. Voila!
Read more...
$19.15
In Stock
Dryer Thermal Fuse
Fix Number FIX11741460
Manufacturer Part Number WP3392519
The dryer thermal fuse, also sometimes referred to as the thermal cut off or temperature fuse, is a 2 by 1/2-inch, white, plastic safety mechanism that halts the flow of electricity to the motor circuit when a dryer overheats. If the fuse is missing or broken, your dryer will not start. A thermal fuse fails when the exhaust temperature exceeds the fuse rating, that is when the temperature rises above the temperature that the fuse is intended to manage. This can be caused by the heating element shorting, a regulating thermostat or thermistor failure, or with a partially restricted exhaust vent. The fuse attaches to the blower wheel housing. It must be replaced when there is no longer continuity between the terminals. This is a one-time fuse, meaning it cannot be re-set. The replacement part features two 3/16-inch terminals. While performing this repair, we recommend checking to make sure all vents are cleared and vacuumed. This OEM part is sold individually.
Fixes these symptoms
- Heat stays on after drum has stopped
- Not Heating
- Too hot
- See more...
Installation Instructions
gary from apex, NC
dryer not heating
Checked the heating element and found a break in the heating coil. Decided to change the thermal fuse and the the cycling thermostat because of the age of the dryer.
Read more...
$16.77
In Stock
Multi Rib Belt - 92-1/4"
Fix Number FIX346995
Manufacturer Part Number 341241
This multi rib belt is an OEM replacement part for a dryer. It attaches to the drum, idler pulley, and motor pulley, and is responsible for spinning the drum. Over time, the belt can become frayed, brittle, and inflexible. If you can hear the motor running, but the drum does not turn, it is likely that the belt is broken. Other symptoms of a broken multi rib belt include unusual noises, failing to start, no heat, a burning smell, and an unresponsive touchpad. Depending on the model, you will find the belt by looking behind the front panel or under the main top of the dryer. This belt is 1/4-inches wide, has a length of 92-1/4-inches, and has four ridges and three groves on the belt. Each belt is sold separately.
Fixes these symptoms
- Drum Not Spinning
- Heat stays on after drum has stopped
- Noisy
- See more...
$2.63
In Stock
Door Catch Kit
Fix Number FIX334230
Manufacturer Part Number 279570
This kit includes two door strikes, and three door catches, to service doors that have one or two catches. The strike is mounted on the body of the dryer, while the catch is mounted on the dryer door. These two parts work together to keep the dryer door shut while in operation. If your appliances lid will not close, or it will not start, it may be time to replace the door catch. If this part is malfunctioning, it should be replaced immediately, as it is not safe to run a dryer with the door not properly closed. This kit also comes with a set of instructions to help with the repair.
Fixes these symptoms
- Door Pops Open
- Door won’t close
- Lid or door won’t close
- See more...
Installation Instructions
jeffrey from Brookhaven, PA
Dryer would run, but not heat
Needed it running quick, so no diagnostics. Ordered one of everything that could fix problem (plus a new door catch). Tipped it onto it's back & popped the bottom cover off. Element, thermal cutoff, thermistor, and fuse. were right in front and held by 2 screws each (don't drop them, don't ask). A little bit tight inside, but no big issue. vacuumed the inside, replaced everything (it was the Heating Element, by the way), slapped the cover on, and put it back in its spot. works like it was new. Yes, I unplugged it first. Remember! Safety Third!
Read more...
$8.65
In Stock
Light Bulb - 40W
Fix Number FIX2376034
Manufacturer Part Number 8206232A
To access the exterior lightbulb, the bottom panel of the microwave will need to be removed. It is secured in place with screws, so will require a Philips screwdriver to remove it. Screw the new light bulb directly into the light socket. If this is the first time you have replaced this light bulb, the old light bulb might be held in place with silicone. This silicone will need to be cut off using either a utility knife or dental floss before removing the light bulb. Once this silicone and old bulb has been removed, the replacement bulb can be screwed in its place.
Installation Instructions
Mark from North East, PA
Bulb burnt out
Removed the screw holding the bulb cover replaced the bulb. Reinstalled the cover and screw. Remove dirty grease filter replaced with new grease filter.
Read more...
$13.09
In Stock
Roller Support Tri-Ring
Fix Number FIX11755850
Manufacturer Part Number WPW10512946
This small but mighty OEM piece is called a tri-ring and is used to support the drum roller shaft and the idler pulley shaft in your dryer. It helps to provide a tight seal between components by evenly distributing pressure. The part is triangular in shape, and less than an inch in size. Overtime it can become brittle or compressed, which can lead to a noisy tumbling cycle, or your dryer not tumbling at all. The tri-ring itself is simple to replace, simply slip off the damaged one and slip on the new. However, to access the drum roller or idler pulley, you will need to remove the front panel and drum of your dryer. This may require tools like a Phillips screwdriver, a quarter inch nut driver, putty knife, a small flat blade screwdriver, and a pair of needle nose pliers depending on your model. Ensure that the power is disconnected before beginning your repair.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
JAMES from GREENSBURG, PA
Loud squeaking and squealing
Lint Filter - Removed old lint filter and inserted new lint filter. This is the first time I tried to fix a dryer. A handyman I am not. I found two very useful YouTube videos using basically my model of Kenmore (11067851600). Disassembly/Assembly - here is a difference between Kenmore 29" wide dryers and 27" wide dryers. Mine is 27". My effort was not a smooth as these videos. The bottom front panel's right most clip was quite troublesome. The moisture sensor wire required needle nose pliers to be disconnected and reconnected. The open door sensor was not easy to disconnect. Although with a few special magic words it came apart. The upper front panel was held in place with two T20 Torx screws. I had only had a T15 driver, therefore a trip to Home Depot was required. The first two tri rings were not easily removed, however, on third tri ring it became easier and not damaged. Replacement of tri rings was not troublesome. Support rollers snapped in place easily. However, I did thoroughly clean the housing. It was quite grimy. Actually, while I had the dryer open I cleaned everything including the heating element and electric motor. It now operates quietly. It took me a little over two hours because I am not handy and must take care not to make matters worse plus I thoroughly cleaned everything include scuff marks where the drum rubs. Anyone else probably should have it completed 30-60 minutes easily.
Read more...
$30.86
In Stock
Refrigerator Door Switch
Fix Number FIX12728638
Manufacturer Part Number W11384469
Door switch turns the light off when you close the door.
Fixes these symptoms
- Light not working
- See more...
Installation Instructions
Marilyn from Dublin, OH
Light switch no longer worked
Turn off and unplug your refrigerator. I used the screwdriver on the left side of the part (where the plug is) and used the putty knife at the same time on the right side to push the spring lock portion of the part in. The part snapped out. I unplugged the left contact from the plug and put it on the new part, then I unplugged the right contact and put it on the new part. I did this so the wires would not go up into the refrigerator and be hard to find. I put the left side of the new part where the plug and contacts are in first then I snapped the right side in place. I plugged the refrigerator back in and it worked perfectly. Just take your time and gently remove and reconnect the new part. The store where I bought my refrigerator wanted $69.95 for a service call plus an hourly charge and part charge. Count on this site for your parts and do it yourself. I ordered the part on Monday, it was delivered on Tuesday around noon and I made the repair that afternoon.
Read more...
$10.46
In Stock
Lower Door Closing Cam
Fix Number FIX11739042
Manufacturer Part Number WP2182179
The lower door closing cam raises the door to keep it from touching the refrigerator liner when the door is closed. It fits both the left and right side of the refrigerator door. The most common reasons for replacing this part are the fridge door slips down when opened, the door does not open smoothly, or does not close by itself. This original part is made of durable black plastic, is approximately 1.1 inches by 1.5 inches, and is sold individually. To effectively install this part, you will need a 5/16 nut driver and a small flat blade screwdriver. Before you begin, disconnect the power and the water supply. We suggest lubricating this part before installing. To make the repair, remove the top hinge cover, then the top hinge support. Lift the door from the bottom support and remove the old door cams. Replace the cams and put the door back on the lower hinge support. Replace the top hinge support and that completes the repair.
Fixes these symptoms
- Clicking sound
- Door Sweating
- Door won’t open or close
- See more...
Installation Instructions
Curtis from Highland, UT
The door would not stay closed, the closing cams were completely worn out.
This is a very simple repair, by far the hardest part was emptying all of the condiments out of the door. After that was done I removed the top hinge cover and then the hinge. I lifted the door off of the refrigerator and set it on a card table so that it was off the ground. I took the worn cams off of the door and the refrigerator cabinet (one screw for each of them). I screwed the new cams into position and lubricated them with petroleum jelly. Then I put the door back in position and reattached the top hinge. It works perfectly again.
Read more...
$67.26
In Stock
Refrigerator Crisper Drawer with Humidity Control
Fix Number FIX11739119
Manufacturer Part Number WP2188656
This is a genuine OEM replacement crisper drawer for refrigerators. It is sold as an individual part. The crisper drawer with humidity control allows you to adjust the humidity within the crisper, which can help preserve the quality of your produce. It attaches to the inner part of the refrigerator to the bottom of the crisper shelf. If your crisper drawer is missing, cracked, damaged, or discolored, it needs to be replaced. It is made of durable clear plastic with a white handle and is sold individually. No tools are needed for installation, simply slide the new crisper drawer into the tracks.
Fixes these symptoms
- Clicking sound
- Door Sweating
- Door won’t open or close
- See more...
Installation Instructions
Ollie from Sayville, NC
Replace Crisper Drawer with Humidity Control
Pull refrigerator from wall to be able to open the door wide enough to slide old Crisper out and slide new one in. Push refrigerator back in place!
Read more...
$4.28
In Stock
Agitator Directional Cogs
Fix Number FIX388034
Manufacturer Part Number 80040
Commonly referred to as dog ears, these agitator directional cogs are manufacturer approved replacement parts that come in a package of 4 and are usually used with direct drive washing machines. We recommend replacing all 4 directional cogs at the same time. The agitator directional cogs reach across the gear teeth in one direction and dig into the gear teeth in the other direction to create the needed agitation. This thrusting motion is what tumbles your clothes during the wash cycle. When the teeth on the outer edge are damaged, the cogs will not engage with the upper agitator, making it impossible to agitate as it should. If your machine makes unusual noises, shakes/moves while operating, or will not spin or drain properly, it may be time to replace them. To access this part, simply remove the softener dispenser and then the agitator cap. You will find them attached to the agitator. Each cog is approximately 1 inch long and made of a durable plastic.
Fixes these symptoms
- Does not dispense fabric softener or detergent
- Marks left on clothes
- Not cleaning dishes properly
- See more...
Installation Instructions
John from La Mesa, CA
Upper agitator stopped working
Followed the simple instructions on youtube, searching for "kenmore upper agitator doesn't work." There are a number of videos there. Find the notch on agitator cover and pry off the cover using a flat screw driver. Remove the nut in the center of the agitator using the 7/16 socket with extension. Remove upper agitator (mine came off easily but some may require removing the entire agitator, then pulling off the upper agitator). Remove assembly from inside and replace the dogs. Reassemble.
Read more...
Appliance Type
- Whirlpool Cooktop Parts
- Whirlpool Dishwasher Parts
- Whirlpool Dryer Parts
- Whirlpool Food Waste Disposer Parts
- Whirlpool Freezer Parts
- Whirlpool Laundry Accessories Parts
- Whirlpool Microwave Parts
- Whirlpool Microwave Oven Combo Parts
- Whirlpool Range Parts
- Whirlpool Range Hood Parts
- Whirlpool Refrigerator Parts
- Whirlpool Trash Compactor Parts
- Whirlpool Wall Oven Parts
- Whirlpool Washer Parts
- Whirlpool Washer Dryer Combo Parts
- Whirlpool Grill Parts
- Whirlpool Air Conditioner Parts
- Whirlpool Air Purifier Parts
- Whirlpool Dehumidifier Parts
- Whirlpool Cabinet Parts
- Whirlpool Workbench Parts
- Whirlpool Ice Maker Parts
- Whirlpool Miscellaneous Parts
- Whirlpool Food Processor Parts
- Whirlpool Mixer Parts
- Whirlpool Warming Drawer Parts
Popular Whirlpool Models
- WRS325FDAM04 REFRIGERATOR
- WRS325FDAM02
- WDT750SAHZ0 DISHWASHER
- WDTA50SAHZ0 DISHWASHER
- WRF535SMBM00 REFRIGERATOR
- WRX735SDBM00
- WED4815EW1 ELECTRIC DRYER
- GHW9150PW0 Residential
- WDT970SAHZ0 DISHWASHER
- GHW9100LW1 Residential, Direct Drive
- GEW9250PW1 Residential
- WRS571CIHZ01
- WRS322FDAM04 REFRIGERATOR
- ED2KVEXVQ01 Side-by-side
- ED5KVEXVB00 Side-by-side
- WFW9151YW00 Residential
- WRS588FIHZ00
- WDT780SAEM1 DISHWASHER
- WRS571CIDM01 REFRIGERATOR
- WFW9150WW01 Residential, Automatic