Whirlpool Mixer Parts
Start With Your Model Number
Find Parts Fast
Guaranteed Fit
Repair Videos
Need help finding your model number?
Popular Whirlpool Mixer Parts
$20.99
In Stock
Worm Gear
Fix Number FIX11748374
Manufacturer Part Number WPW10112253
This part includes one worm gear for a stand mixer. It measures approximately 1.5-inches in diameter and is sourced directly from the manufacturer. The worm gear is responsible for turning the planetary where the accessories attach. A few common reasons for replacing this part include, unusual sounds (grinding) or if it will not start.
Fixes these symptoms
- Touchpad does not respond
- See more...
Installation Instructions
Melody from Silverton, CO
stripped the worm gear, fixed bushings
I opened the mixer and determined that the worm gear had failed, as designed, to save the other gears. There was also oil separated from the grease and it needed replaced. The Transmission case gasket was damaged and must have been from the time it was built. I removed the grease with putty knife and kept I on a plastic plate until the parts came in (to determine the amount needed when I replaced it.) I used the punch to remove the two pins needed with light tap from hammer. I left the mixer in pieces on the counter until the parts arrived. I replaced the gear and all other parts and placed fresh grease in the mixer. I had to adjust the beater, too. I had removed one of the bushings by mistake. When mixer was back together it would not start. IT TOOK SOME TIME BUT I FOUND ANOTHER WEB SITE THAT EXPLAINED HOW TO REPLACE THE BUSHING. TAKE A FLASHLIGHT AND LOOK INTO THE SQUARE BRUSH HOLDER. THERE IS A DETANT IN THE HOLDER. THE SHAVED SIDE OF THE BRUSH NEEDS TO SLIP PAST THE DETENT TO BE ABLE TO TOUCH THE AMATURE. Once that was done, it worked great. Very smooth with new gear and grease.
Read more...
$8.16
In Stock
Retaining Ring
Fix Number FIX11746909
Manufacturer Part Number WP9703438
Sometimes referred to as a retaining clip, the retaining ring is used to hold the drum support roller onto the shaft in your dryer. The clip may need to be replaced if you find that your dryer is noisy while tumbling or will not tumble at all. The retaining clip can also be used with stand mixers, to hold the pinion gear to the agitator shaft. This genuine OEM part is made entirely out of metal and measures approximately half an inch in diameter.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Brian from Novi, MI
Squeaking noises while running dryer
Followed the Video Directions from website. All went as planed. The dryer is running like new now.
Read more...
$8.32
In Stock
Motor Brush
Fix Number FIX11753983
Manufacturer Part Number WPW10380496
This genuine OEM part is a motor brush for your stand mixer. The brush is sold individually, however, there are two motor brushes on your mixer, and we recommend replacing both at the same time, as they tend to wear out at the same rate. A sign that you may need to replace the brushes is if your mixer is running slowly. A flat blade screwdriver is needed to remove the brush cover in order to replace this part.
Fixes these symptoms
- Touchpad does not respond
- See more...
Installation Instructions
James from Windsor, NY
Internal Worm Gear to Electric Motor Stripped
After looking at your sites great exploded views I was able to disassemble the motor assembly. Replaced the brushes and damaged gear assembly . Reassembled Worked great.Wife's china made mixer had diecast internal parts that shattered after her attempt to mix cookie dough. Now with this USA made Kitchen Aid Mixer she can mix concrete with coke bottles and never work hard. Thank You for you great site and delivery ethic. Only wish my Hitachi ex50urg excavator had a parts exploded views as you do. Also Worm gear and bracket had improvements to redirect lube grease to keep improved gear material well lubricated.
Read more...
$26.98
In Stock
Flat Beater
Fix Number FIX11757063
Manufacturer Part Number WPW10672617
This flat beater is a genuine OEM part for your stand mixer. If your beater has become worn out or is missing, this is the replacement you need. The beater is white in color and has a powder coated finish. We recommend hand washing this part, as the coating can wear faster if you are using the dishwasher. No tools are required, simply swap out the beater like you would with any of the mixer attachments.
Fixes these symptoms
- Touchpad does not respond
- See more...
Installation Instructions
Jeptha from CHANUTE, KS
$34.32
In Stock
Worm Gear and Bracket
Fix Number FIX11740516
Manufacturer Part Number WP240309-2
Used for Kitchenaid Mixers.
Fixes these symptoms
- Touchpad does not respond
- See more...
Installation Instructions
James from Windsor, NY
Internal Worm Gear to Electric Motor Stripped
After looking at your sites great exploded views I was able to disassemble the motor assembly. Replaced the brushes and damaged gear assembly . Reassembled Worked great.Wife's china made mixer had diecast internal parts that shattered after her attempt to mix cookie dough. Now with this USA made Kitchen Aid Mixer she can mix concrete with coke bottles and never work hard. Thank You for you great site and delivery ethic. Only wish my Hitachi ex50urg excavator had a parts exploded views as you do. Also Worm gear and bracket had improvements to redirect lube grease to keep improved gear material well lubricated.
Read more...
$22.91
In Stock
Speed Control Plate
Fix Number FIX11748567
Manufacturer Part Number WPW10119326
Used in Mixers.
Installation Instructions
scott from stuart, VA
speed control went bad( either off or fast)
ordered the speed control board from this site and put it in the hardest part was getting the top of the blender off since it was never removed before. also beware there is a thin spring attached to the bottom of the board if not careful you could loose it and then you have to take more of the blender apart.
Read more...
$31.74
In Stock
Wire Whip Mixer
Fix Number FIX11746928
Manufacturer Part Number WP9704329
This wire whip is for stand mixers.
Wire whip attaches to the beater shaft and incorporates air into cream, eggs and frostings.
Follow the instructions in the owner's manual for using and installing this part.
Fixes these symptoms
- Touchpad does not respond
- See more...
Installation Instructions
Gehrounda from Durant, OK
Been using a paddle, didn't have a wire whip.
I had put off ordering one because I just knew it was not going to fit and didn't want the hassle of returning it. If I had only known how easy it was too order and that it would've fit I could have been using it years ago.Took me all of 1 minute by time I opened the box, washed it and put it on. You really should have a shorter time than 15 minutes on your survey. Wondered why other customers put 15 minutes installing the whip. Now I know. Glad I went ahead and ordered one. Thank you for a job well done. Will definitely be ordering from you again if need be.
Read more...
$9.03
In Stock
Retaining Pin
Fix Number FIX11746974
Manufacturer Part Number WP9707223
This part works in conjunction with the worm and bevel gear.
Installation Instructions
Bob from NORTH AUGUSTA, SC
The mixer would not spin.
Took the cover off of the transmission and replaced gears, pin and gasket and added new grease.
Read more...
$8.99
In Stock
Foot
Fix Number FIX11747035
Manufacturer Part Number WP9709707
Sold individually.
Fixes these symptoms
- Touchpad does not respond
- See more...
Installation Instructions
James from Shelby Twp, MI
Powers on monentarily at lowest speed. No other speeds work.
Primary problem was a bad speed control plate (SCP). I removed the rear cap exposing the speed control plate and pressed the adjustment screw while I changed speeds. It started working but saw sparking on the SCP contacts. Decided to first change out the worm gear & grease. 3 oz container of grease is avialable from Amazon. Don't buy the 1# pkg. You'll end up tossing most of it out. Contrary to other posts you must use food-safe grease, in case a leak develops, which was the case here. New control plate arrived damaged but the site replaced it promptly. Plate is labeled with wire colors but hard to read in dim light. Suggest drawing a diagram of the wire colors & placement before disconnecting. Also spent extra time adjusting the 3 screws on the plate so the mixer operated smoothly at all speeds. Rubber foot was much smaller & taller than the others and caused the mixer to rock slightly. Trimmed off the top and it worked fine.
Read more...
$20.48
In Stock
Transmission Case Gasket
Fix Number FIX11742306
Manufacturer Part Number WP4162324
This part is used with Kitchenaid Mixers.
Installation Instructions
Melody from Silverton, CO
stripped the worm gear, fixed bushings
I opened the mixer and determined that the worm gear had failed, as designed, to save the other gears. There was also oil separated from the grease and it needed replaced. The Transmission case gasket was damaged and must have been from the time it was built. I removed the grease with putty knife and kept I on a plastic plate until the parts came in (to determine the amount needed when I replaced it.) I used the punch to remove the two pins needed with light tap from hammer. I left the mixer in pieces on the counter until the parts arrived. I replaced the gear and all other parts and placed fresh grease in the mixer. I had to adjust the beater, too. I had removed one of the bushings by mistake. When mixer was back together it would not start. IT TOOK SOME TIME BUT I FOUND ANOTHER WEB SITE THAT EXPLAINED HOW TO REPLACE THE BUSHING. TAKE A FLASHLIGHT AND LOOK INTO THE SQUARE BRUSH HOLDER. THERE IS A DETANT IN THE HOLDER. THE SHAVED SIDE OF THE BRUSH NEEDS TO SLIP PAST THE DETENT TO BE ABLE TO TOUCH THE AMATURE. Once that was done, it worked great. Very smooth with new gear and grease.
Read more...
Appliance Type
Related Pages
- Whirlpool Mixer Attachments and Accessories
- Whirlpool Mixer Hardware
- Whirlpool Mixer Motors
- Whirlpool Mixer Transmissions and Clutches
- Whirlpool Mixer Wheels and Rollers