Mixer Parts

Shop By Brand

Popular Mixer Parts

$12.58
  In Stock
Worm Gear
★★★★★
★★★★★
(7)
Fix Number FIX11748374
Manufacturer Part Number WPW10112253
This worm gear is an inch and a half in diameter. It is used for some of Whirlpool's brands of mixers.
Fixes these symptoms
Installation Instructions
Melody from Silverton, CO
stripped the worm gear, fixed bushings
I opened the mixer and determined that the worm gear had failed, as designed, to save the other gears. There was also oil separated from the grease and it needed replaced. The Transmission case gasket was damaged and must have been from the time it was built. I removed the grease with putty knife and kept I on a plastic plate until the parts came in (to determine the amount needed when I replaced it.) I used the punch to remove the two pins needed with light tap from hammer. I left the mixer in pieces on the counter until the parts arrived. I replaced the gear and all other parts and placed fresh grease in the mixer. I had to adjust the beater, too. I had removed one of the bushings by mistake. When mixer was back together it would not start. IT TOOK SOME TIME BUT I FOUND ANOTHER WEB SITE THAT EXPLAINED HOW TO REPLACE THE BUSHING. TAKE A FLASHLIGHT AND LOOK INTO THE SQUARE BRUSH HOLDER. THERE IS A DETANT IN THE HOLDER. THE SHAVED SIDE OF THE BRUSH NEEDS TO SLIP PAST THE DETENT TO BE ABLE TO TOUCH THE AMATURE. Once that was done, it worked great. Very smooth with new gear and grease. Read more...
$4.54
  In Stock
Retaining Ring
Fix Number FIX11746909
Manufacturer Part Number WP9703438
This is a retaining ring, also known as a roller retainer clip, and it is for various home appliances. This part is 1/2 an inch in diameter, and made entirely of metal. The retaining ring connects the support roller to the shaft in your dryer. If your dryer is noisy, or taking too long to dry, you may need a new retaining ring. Note that this part can also be used in a refrigerator/freezer, and a washer/dryer combo.
Fixes these symptoms
  • No heat or not enough heat
  • Noisy
  • Takes too long to dry
  • See more...
Installation Instructions
Brian from Novi, MI
Squeaking noises while running dryer
Followed the Video Directions from website. All went as planed. The dryer is running like new now. Read more...
$11.88
  In Stock
Motor Brush
Fix Number FIX11753983
Manufacturer Part Number WPW10380496
Used on Stand Mixers. Sold Individually.
Fixes these symptoms
Installation Instructions
James from Windsor, NY
Internal Worm Gear to Electric Motor Stripped
After looking at your sites great exploded views I was able to disassemble the motor assembly. Replaced the brushes and damaged gear assembly . Reassembled Worked great.Wife's china made mixer had diecast internal parts that shattered after her attempt to mix cookie dough. Now with this USA made Kitchen Aid Mixer she can mix concrete with coke bottles and never work hard. Thank You for you great site and delivery ethic. Only wish my Hitachi ex50urg excavator had a parts exploded views as you do. Also Worm gear and bracket had improvements to redirect lube grease to keep improved gear material well lubricated. Read more...
$15.84
  In Stock
Worm Follower Gear
★★★★★
★★★★★
(1)
Fix Number FIX12070620
Manufacturer Part Number W11086780
This is a manufacturer-approved gear, used in stand mixers.
Fixes these symptoms
Installation Instructions
carol from whittaker, MI
mixer skipped while turning
followed instructional video the hardest part was removing the snap ring! once that was removed it was a piece of cake! Read more...
$17.70
  In Stock
Hub Gear
★★★★★
★★★★★
(3)
Fix Number FIX12348886
Manufacturer Part Number W11192795
Includes both the attachment and beveled gear. This worm follower gear is for stand mixers. Worm follower gear meshes with the worm gear, causing the rotation of the planetary assembly where the accessories attached. Unplug the mixer before installing this part. Wear work gloves to protect your hands.
Fixes these symptoms
Installation Instructions
carol from whittaker, MI
mixer skipped while turning
followed instructional video the hardest part was removing the snap ring! once that was removed it was a piece of cake! Read more...
$20.19
  In Stock
Flat Beater
★★★★★
★★★★★
(1)
Fix Number FIX11757063
Manufacturer Part Number WPW10672617
This has a powder coated finish.
Fixes these symptoms
Installation Instructions
Jeptha from CHANUTE, KS
Covering had worn off the beater
Snap it in place, less than a minute Read more...
$4.67
  In Stock
Retaining Pin
★★★★★
★★★★★
(1)
Fix Number FIX11746974
Manufacturer Part Number WP9707223
This part works in conjunction with the worm and bevel gear.
Installation Instructions
Bob from NORTH AUGUSTA, SC
The mixer would not spin.
Took the cover off of the transmission and replaced gears, pin and gasket and added new grease. Read more...
$14.50
  In Stock
Speed Control Plate
★★★★★
★★★★★
(1)
Fix Number FIX11748567
Manufacturer Part Number WPW10119326
Used in Mixers.
Installation Instructions
scott from stuart, VA
speed control went bad( either off or fast)
ordered the speed control board from this site and put it in the hardest part was getting the top of the blender off since it was never removed before. also beware there is a thin spring attached to the bottom of the board if not careful you could loose it and then you have to take more of the blender apart. Read more...
$29.30
  In Stock
Worm Gear and Bracket
★★★★★
★★★★★
(4)
Fix Number FIX11740516
Manufacturer Part Number WP240309-2
Used for Kitchenaid Mixers.
Fixes these symptoms
Installation Instructions
James from Windsor, NY
Internal Worm Gear to Electric Motor Stripped
After looking at your sites great exploded views I was able to disassemble the motor assembly. Replaced the brushes and damaged gear assembly . Reassembled Worked great.Wife's china made mixer had diecast internal parts that shattered after her attempt to mix cookie dough. Now with this USA made Kitchen Aid Mixer she can mix concrete with coke bottles and never work hard. Thank You for you great site and delivery ethic. Only wish my Hitachi ex50urg excavator had a parts exploded views as you do. Also Worm gear and bracket had improvements to redirect lube grease to keep improved gear material well lubricated. Read more...
$36.76
  In Stock
Wire Whip Mixer
★★★★★
★★★★★
(1)
Fix Number FIX11746928
Manufacturer Part Number WP9704329
This wire whip is for stand mixers. Wire whip attaches to the beater shaft and incorporates air into cream, eggs and frostings. Follow the instructions in the owner's manual for using and installing this part.
Fixes these symptoms
Installation Instructions
Gehrounda from Durant, OK
Been using a paddle, didn't have a wire whip.
I had put off ordering one because I just knew it was not going to fit and didn't want the hassle of returning it. If I had only known how easy it was too order and that it would've fit I could have been using it years ago.Took me all of 1 minute by time I opened the box, washed it and put it on. You really should have a shorter time than 15 minutes on your survey. Wondered why other customers put 15 minutes installing the whip. Now I know. Glad I went ahead and ordered one. Thank you for a job well done. Will definitely be ordering from you again if need be. Read more...

Brands

Popular Mixer Models