This part includes one worm gear for a stand mixer. It measures approximately 1.5-inches in diameter and is sourced directly from the manufacturer. The worm gear is responsible for turning the planeta...
In Stock
Order within the next 3 hrs and your part ships today!
Sometimes referred to as a retaining clip, the retaining ring is used to hold the drum support roller onto the shaft in your dryer. The clip may need to be replaced if you find that your dryer is nois...
In Stock
Order within the next 3 hrs and your part ships today!
This genuine OEM part is a motor brush for your stand mixer. The brush is sold individually, however, there are two motor brushes on your mixer, and we recommend replacing both at the same time, as th...
In Stock
Order within the next 3 hrs and your part ships today!
This wire whip attaches to your stand mixer and is used for whipping food products. It is made of metal wire and is one of several attachments that you can add to your mixer. If you attempt to start y...
In Stock
Order within the next 3 hrs and your part ships today!
This flat beater is used on stand mixers. It is dishwasher safe, however, should only be washed in the upper rack. The Flat Beater is used to mix batters and light doughs. Should the coating become da...
In Stock
Order within the next 3 hrs and your part ships today!
Order within the next 3 hrs and your part ships today!
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched. Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
John
January 27, 2024
My “professional chef” brother decided to deep clean my mixer. It worked quite well when he started but after cleaning it doesn’t work. I found out later he removed the brushes for some reason and upon putting them back in the mixer does not work. I retried the procedure in putting them in with the missing corner fit, small spring plus long spring with brush attached, the cap all assembled per the instructions I found. Still doesn’t work. Removed the back of the motor housing, no burnt wires, no burnt smells, upon checking all the connections with tester, power is present. So, theoretically the mixer should work….. what am I missing? Any help would be greatly appreciated and will get my brother out of the dog house. Thanks,
For model number KSM5
Hi John, thank you for contacting us. Based on the description, the issue is with the motor brushes. We would recommend checking the springs if they are properly aligned with the brush that pushes against the motor rotor itself. The brushes need to be cleaned with electrical contact cleaner and not with soap. If the brushes are aligned properly and still the issue persists, then you may need to replace the motor brush, part number FIX11753983, to fix the issue. We hope this solves your problem!
Pulled the Knob off of the new Lever then pressed it on the old Lever. I had to order the whole lever because it was the part nearest the knob in the illustrated parts break-down. I RECOMMEND THAT THE KNOB BE ADDED TO THE ILLUSTRATED PARTS BREAK-DOWN.
I removed screws in a sequence that I felt wouldn't further damage the mixer until I had it completely unassembled. When I found the broken worm gear, I went online to find a part. I found an exploded view, but the part numbering was old, and the salesperson couldn't tell me what the worm gear and bracket assembly consisted of, as I only
... Read morewanted the worm gear. After trying to drive the pin out of the assembly, and failing, I decided to back online and see if anyone else had a photo of the assembly. Luckily (and wisely) PartSelect,com did and that answered any questions I had. The price was better, too. Reassembly of the mixer was a cinch with the exploded view. It's working like new, and we're hoping for another 35 years of service from it! Thanks.
My girlfriends' stand mixer failed when the accessory drive cap fell into the mixing bowl and jambed the beater, spliting the worm gear. The teeth on this gear are made of nylon and are molded to an aluminum center. This part is designed to fail in situations like this, saving the more expensive transmission parts. Following a repair manu
... Read moreal I found online, I first removed the rear cover and pulled out the cord strain relief out from the base. Next I removed the drip cup from around the base of the planetary drive. I then used a pin punch to drive out the pin holding the planetary to the center shaft and removed the planetary. The unit was then inverted and I removed 4 screws holding the bottom cover to the gear case, and the 5 screws from around the planetary drive. The bottom cover was then lifted off. Three screws holding the worm gear bracket in place were then removed and the worm gear assembly lifted out. A small pin holds the worm gear to the shaft. I drove this out with a small pin punch and the shaft and worm gear were then removed. There is also a thrust washer on this shaft, and it's location is important. Make a note for re-assembly. The new gear was installed and the entire process reversed for re-assembly. A successful repair completed! My girlfriend would have replaced this $200 appliance, but I was able to repair it for less than $30 including shipping.