Dishwasher Parts

Popular Dishwasher Parts

★★★★★
★★★★★
10 Reviews
Fix Number
FIX10065979
Manufacturer Part Number
W10712395
This OEM dishwasher upper rack adjuster kit includes the left and ride side adjusters and all the parts needed to repair the upper rack. These parts have changed from plastic to metal, so even though it looks different than the original part, it is made to be perfectly compatible. This part is located on the dishwasher rack and is connected to the track, allowing it to move in and out smoothly. If this part is damaged, it may make it difficult to move the rack in and out or it might hang down awkwardly, indicating a repair is needed.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...

Installation Instructions

gregory from cooperstown, NY
New parts are not identical to original
I was expecting original equipment parts, so initially opening the box I was surprised and thought that I would be sending them back. The new parts were, however, correct, and actually of better quality than the original. More steel and less plastic. Dimensions were the same but connections were very different. Instructions were included with photos instead of diagrams. I do prefer well drawn "exploded" diagrams, based on years of experience putting tools and machinery together. The first rack adjuster took 10 minutes and a little head scratching, but the second one took about two minutes. Add about three minutes to remove the old adjusters and the entire job took 15 minutes. I would advise the manufacturer to provide a detailed diagram instead of photos. Read more...
★★★★★
★★★★★
12 Reviews
Fix Number
FIX3406971
Manufacturer Part Number
W10195416
This OEM gray plastic lower dishrack wheel assembly allows the rack to slide in and out of the dishwasher with ease. It measures roughly 3 by 6 inches. If it breaks or becomes damaged it may make sliding in and out feel difficult. This is a normal wear and tear item and will need to be replaced when this happens. It attaches directly to the dishrack and is a quick and easy repair. There are 4 dishrack wheel assemblies in total on your appliance, so this is a good time to inspect all 4, as this part is sold individually. To repair, open the dishwasher door and pull out the lower dishrack. Next, push the tab from both sides and it should pop out. To install the new wheel assembly, place it on the rack and make sure the caps overlap the wire from the inside before you clip it in place by pushing the wheel.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...

Installation Instructions

Anthony from Helena, MT
Wheels and hubs have melted and broken frequently
Easy to install. Snap right on to lower basket. Read more...
Lower Spray Arm
$35.34
In Stock
★★★★★
★★★★★
4 Reviews
Fix Number
FIX12585623
Manufacturer Part Number
5304517203
This is a single lower spray arm found in dishwashers to spray water and detergent vigorously over the dishes. This spray arm is made of plastic, so can warp or crack with time. The holes in the spray arm can get clogged with debris, so it should be cleaned every so often. If it is beyond cleaning or damaged, it will need to be replaced. If the holes are clogged, this can sometimes mean there is a problem with the filter system, so it is a good idea to inspect this as well. For this repair, start by turning off the water supply to the dishwasher. Pull the lower rack out of the dishwasher and out of the way. Remove the lower wash arm. Using a flathead screwdriver, push the small locking tabs located on each side at the bottom of the spray arm. You should now be able to easily pull the spray arm out of the dishwasher. Align the new lower wash arm and push it down to secure it in place. Make sure it can spin freely and is not making contact with the heating element. Place the lower dishrack back into the appliance and close the door.
Fixes these symptoms

Installation Instructions

Leesa from Clarksburg, WV
Took lower stray arm off because of draining issues, put back together and arm melted after starting.
The reviews before mine helped A LOT!! First of all, It has everything to do with making sure that when the arm is installed that it is turned until it clicks/locks in. This is why my arm melted when I put it back together the first time. I read the reviews before I purchased and that was really the only way I knew how to repair the piece. It does not come with instructions. Read more...
Rack Track Stop
$7.70
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX11746591
Manufacturer Part Number
WP8565925
This is a single rack track stop clip used to prevent the upper dish rack from sliding all the way out of the dishwasher. It is made of gray plastic and can wear with time. This is an easy repair that should not take very long to complete. Start by opening the dishwasher door, depress the tabs to remove both the front stop clips and remove the upper dish rack from the appliance. Now, using your small flat head screwdriver, release the retaining tab to remove the rear stop track that you are replacing, and pull the clip up to remove it. Install the new clip by inserting it into the support rail from the top and press it down to secure it in place.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Noisy
  • See more...

Installation Instructions

Richard from Austin, TX
Wheels on original upper rack adjust fell off and end stops would not stay on.
Removed old end stops. Pulled rack out of machine. Carefully removed old adjusters. Snapped in new adjusters. Slid rack back into the runners. Clipped in the new end stops. Done. Read more...
Dishwasher Upper Rack Adjuster
$43.81
In Stock
★★★★★
★★★★★
4 Reviews
Fix Number
FIX11756150
Manufacturer Part Number
WPW10546503
This dishrack adjuster attaches to the side of the top dishrack and fits both the left and ride side. If you are looking to replace both sides, you will need to order 2 of this part, as they are sold separately. It connects to the track, making it possible to move the rack in and out as well as raise up and down to accommodate different size items. If this part breaks, it may make it difficult for the rack to slide in and out with ease, in which case it will need to be replaced, as this can lead to further issues. For this repair, remove the upper rack from the dishwasher, detach the adjuster housing cover and then detach the front and rear adjuster support straps from the tines. Pry off the stop clip to detach the old adjuster. Align the new adjuster on the rack and snap the stop clip in place to secure it. Place the front and rear support straps back on. Position the adjuster housing and place the cover back on to secure. Place the rack back into the dishwasher.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...
★★★★★
★★★★★
3 Reviews
Fix Number
FIX9495545
Manufacturer Part Number
809006501
This dishwasher door gasket is attached to the bottom of the door, creating a strong seal between the tub and the outer edge of the door. This seal is prone to wear and tear due to its constant exposure to water, detergent, and food particles. If the gasket appears cracked, broken, or you notice a leak coming from the door, it will need to be replaced immediately. This gasket measures approximately 23 inches long. For this simple repair, no tools are necessary. Open the dishwasher door and remove the bottom rack. The gasket is located right along the bottom of the door, molded inside the channel. It is held in place in the groove across the bottom. Remove the old gasket by pulling it out with your hands. Take your new silicone gasket and line it up so the notch fits into the groove and slide it in place until it is secure. Reinstall the lower dishrack. We recommend leaving the door closed for a few hours to ensure the gasket is sealed tightly.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...

Installation Instructions

Everette from Hardyville, VA
Dishwasher leaking around bottom of door
Watched the video, easy replacement. Read more...
Lower Dishrack Wheel Assembly
$36.70
In Stock
★★★★★
★★★★★
6 Reviews
Fix Number
FIX11750057
Manufacturer Part Number
WPW10195417
This gray plastic lower dishrack roller is a part for your dishwasher. It attaches to the bottom of the lower dishrack, allowing it to move in and out smoothly. If the lower dishrack stops moving in and out easily or preventing you from being able to shut the dishwasher door, inspect the dishrack roller for damage. The assembly includes 2 rollers and the bracket that attaches to the dishrack (parts are not sold separately). This assembly is sold individually, so you will need 4 assemblies to replace them all in your appliance. For this easy repair, start by removing the lower dishrack from the appliance and set it on the counter. Use a screwdriver to pry off the old roller assembly from the lower tabs. Align the new part on the dishrack by snapping it in place.
Fixes these symptoms

Installation Instructions

JEROME from MAPLE GROVE, MN
Wheel fell off the wheel assembly.
Step 1: Snapped the old wheel assembly off.
Step 2: Snapped the new wheel assembly on.
Read more...
Fix Number
FIX8260227
Manufacturer Part Number
154827601
The door gasket provides a watertight seal between the tub and the door, to keep water from leaking out of your dishwasher. If your dishwasher is leaking you may need to replace the door gasket. This gray door gasket is made of rubber and measures approximately 73 inches. For this repair, open the dishwasher door and remove the lower dish tray. Use your hands to pull out the old gasket. Clean the channel with a rag. Press the new gasket in place so it sits inside the groove in the door. Keep the door closed tightly for a few hours to ensure a strong seal is made.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...

Installation Instructions

Patrick from Pleasanton, CA
leak from door
I ordered the top 3 parts in terms of probability of solving the problem (water inlet valve, tub gasket, and bottom door gasket). I installed all 3 and it did not solve the door leak. Then I realized that the bottom door gasket had come out (in other words, I had not installed it properly). I reinstalled the bottom door gasket (a critical point is that it has to be *pressed in* firmly -- there should be some resistance), and it worked. Note that the bottom door gasket is a hybrid between a true seal and a splash guard. The notch in the middle is designed to drain water from the door back into the tub. Because of that notch opening, there is sputtering and splashing at various points of the wash cycle. This appears to be by design, and those splashes result in water being absorbed by the insulating foam. Thank you to the previous submission/posting authors, as this is what clued me in. Read more...
LOWER SPRAY ARM
$19.70
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX17137081
Manufacturer Part Number
WD22X33499
Fixes these symptoms
  • Leaking
  • Noisy
  • Not cleaning dishes properly
  • See more...

Installation Instructions

Kevin from SUN CITY WEST, AZ
Rhythmic noise from bottom spray, arm, banging on heat element
Replace bottom spray arm assembly Read more...
LOWER RACK ROLLER
$13.11
In Stock
Fix Number
FIX16217024
Manufacturer Part Number
WD12X26146
The roller helps the lower rack of your dishwasher to smoothly slide in and out of your appliance. A broken or worn roller wheel can make it clunky or difficult to get the rack in and out of the dishwasher, and the part should be replaced. The rollers are sold individually, however there are four in total in your dishwasher. You may want to replace all at the same time to ensure they have even wear. Replacing a broken roller is a simple job and may require the use of a flat blade screwdriver. Remove the entire lower rack from your dishwasher and place it on a suitable work surface. Release the tabs to open the cover on the roller assembly, using the screwdriver if necessary to pry them open. Pull the damaged wheel off the assembly and push the new one into place. Reattached the cover and place the rack back into the bottom of your dishwasher. The lower rack should now easily glide in and out. These rollers are genuine OEM parts that measure approximately 1.5 inches in diameter and are charcoal in color.

Dishwasher Brands

Related Dishwasher Parts

Popular Dishwasher Models