Inglis Dishwasher Parts
Start With Your Model Number
Find Parts Fast
Guaranteed Fit
Repair Videos
Need help finding your model number?

Popular Inglis Dishwasher Parts
$10.27
In Stock
Rack Track Stop
Fix Number FIX11746591
Manufacturer Part Number WP8565925
This is a single rack track stop clip used to prevent the upper dish rack from sliding all the way out of the dishwasher. It is made of gray plastic and can wear with time. This is an easy repair that should not take very long to complete. Start by opening the dishwasher door, depress the tabs to remove both the front stop clips and remove the upper dish rack from the appliance. Now, using your small flat head screwdriver, release the retaining tab to remove the rear stop track that you are replacing, and pull the clip up to remove it. Install the new clip by inserting it into the support rail from the top and press it down to secure it in place.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Not cleaning dishes properly
- See more...
Installation Instructions
Richard from Austin, TX
Wheels on original upper rack adjust fell off and end stops would not stay on.
Removed old end stops. Pulled rack out of machine. Carefully removed old adjusters. Snapped in new adjusters. Slid rack back into the runners. Clipped in the new end stops. Done.
Read more...
$66.15
In Stock
Dishwasher Heating Element
Fix Number FIX8260087
Manufacturer Part Number W10518394
This is a manufacturer-approved heating element and 2 washers. If the dishes in your dishwasher are not drying or the water in the dishwasher is not getting hot, it may be due to a failed heating element. The heating element is not intended to heat the water that enters the appliance but is designed to maintain the heat of the water that enters. This part is located on the bottom of the appliance. Be sure to disconnect the power to the appliance before you begin this repair. Start this repair by disconnecting the wires from the bottom of the element in the back, remove the plastic nuts holding it in place, remove the element, and repeat these steps in reverse order to install the new part. For this beginner repair, you will need a screwdriver, wrench set, and it should be completed in less than 30 minutes.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not draining
- See more...
Installation Instructions
Jesse from Mandan, ND
not drying or cleaning dishes
Turned off breaker at power source. Turned off water supply valve. Disconnected water supply hose and drain hose. Removed base panel with 1/4'' nut driver. Removed power box cover screw with 1/4'' nut driver, turned off wire nuts connecting power cable and used phillips screw driver to remove ground. Removed 2 phillips screw under front of counter holding dishwasher in place. rolled dishwasher out of cabinet and layed face down on towels. Pulled two wires connected to the element marking position prior. Then removed two heater element nuts with adjustable wrench. Tipped dishwasher up, opened door and lifted out lower rack, underlower rack is heating element and lifted out. Reverse procedure to install.
Read more...
$11.10
In Stock
Rack Adjuster
Fix Number FIX11750255
Manufacturer Part Number WPW10204131
This is a genuine OEM replacement rack adjuster for your dishwasher. If this part is damaged, broken, or missing it may cause issues using the top rack properly. To replace this part, first remove the top rack from your dishwasher, by removing the rack stop clips from the ends of the rails. To release the tabs, you can either use your fingers or a flat blade screwdriver to depress the locking tabs. Once the top rack has been removed and placed on a suitable work surface, the defective rack adjuster can be removed, once again using either your fingers or screwdriver to disengage the tabs. The new rack adjuster can then be snapped into place.
Installation Instructions
Anthony from EASTHAMPTON, MA
Both left and right front rack adjusters fell apart
I briefly watched a YouTube video and looked at the placement of the remaining two rack adjusters. They broken one were easy to take out. New ones were easy to put in. Just remove the top rack completely from the rails. I bought four and replaced all four just to be on the safe side
Read more...
$7.95
In Stock
Rubber Washer
Fix Number FIX11743934
Manufacturer Part Number WP717273
Sold individually. Used with the heating element.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not drying dishes properly
- See more...
Installation Instructions
Mark from Belmont, MI
Heating element failed
1)Turned power off to dishwasher 2) removed toekick cover 3) shut off water 4) disconnected water line to dishwasher 5) removed top screws holding DW in place 6) slid DW out of cavity to access the read bottom 7) removed terminal clips from bottom side of heating element under DW 8) remover special "nuts" that held the heat element in place under DW 9) removed old heat element from inside DW 10) installed rubber wagers on. New heat element 11) installed new heat element from inside DW through holes in back of DW 12) screwed "nuts" back onto the new heat element under DW .... Note .... The new element used different "nuts" than the original .... So I was glad I had ordered new "nuts" just in case and would suggest you do the same 13) attach the electrical connections back on the new heating element 14) slide the DW back under the counter and attach to counter top nosing 15) hooked the water back up and turned it on 16) turned the breaker back on
Read more...
$16.85
In Stock
Mounting Bracket
Fix Number FIX11745496
Manufacturer Part Number WP8269145
The mounting bracket is used to secure the top part of your dishwasher to the underside of your counter or cabinet. If you have solid surface counters (granite, quartz, etc.) you will likely need to side mount your appliance, and this type of bracket is sold separately. It is important to properly secure your dishwasher, as it helps to keep it level, and prevents it from moving, shaking, or tilting forwards. This is an authentic OEM part, made entirely of metal, and approximately 3 inches in length. These mounting brackets are sold individually, however most dishwashers require at least two brackets to secure the appliance to the countertop. It is recommended to check and replace all brackets at the same time, as they tend to wear at the same rate. Attaching the mounting bracket to the top of the dishwasher is simple, and just requires a pair of needle nose pliers to bend the tabs into place. When it comes time to attach your dishwasher to the countertop, please note that you will need screws (sold separately), a screwdriver, and if this is the first time the brackets are being attached, you will also need to use a drill bit to make pilot holes for the screws.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Leaking
- See more...
Installation Instructions
julie from arroyo grande, CA
Mounting bracket broken. Upper rack wheel broken.
Upper Rack Wheel Assembly - This is a little time consuming (maybe 15 minutes), but easy. You will need to remove the entire upper rack assembly before replacing the wheels. After you remove rack assembly and the dishwasher from under the cabinet (see guidance below for brackets), you will see two hex head sheet metal screws with integral washers on the outside of the dishwasher holding the wheel assembly onto the dishwasher. Use the pliers to remove the screws and the old wheel assembly. Install the new wheel and mount assembly using the old screws since the wheel assembly doesn't come with the mounting screws. Mounting Bracket - Pretty easy. Remove port cover for both left & right mounting screws on inside of dishwasher. Remove the screws (if they haven't already fallen out). Careful - they will drop to the floor. Pull the dishwasher partially out from under the counter. Remove the old bracket(s) and install the new one(s). You will need pliers to bend the tabs over to secure them. For the Kenmore, you need to break off the longer end. Slide the dishwasher back under the counter and align the screw holes with the cabinet. I use masking tape to hold the screw on the screwdriver so it doesn't fall off when inserting into the screw hole in the cabinet. Use the flashlight to help see that the holes are aligned. Tighten the screw and you're done.
Read more...
Touch-Up Paint - White
Fix Number FIX385132
Manufacturer Part Number 72017
18ml
Installation Instructions
Al from Cape Coral, FL
No heat when trying to dry clothes .
Followed instructions on your videos. Everything went as planned and the dryer works like new....
Read more...
$10.48
In Stock
Friction Sleeve
Fix Number FIX11745488
Manufacturer Part Number WP8268961
The friction sleeve, sometimes called a friction pad, is made of a flexible black plastic and measures a bit over one inch in length. It is designed to reduce the friction between the hinge and the door on your dishwasher, and helps keep it quiet when the door opens and closes. If the door to your dishwasher drops quickly when unlatched, you may need a new friction sleeve. The sleeve is sold individually however there is one located on both the left and right side of the dishwasher. We recommend replacing them at the same time so that they wear evenly. Replacing this genuine OEM part is an easy repair, but it will require you to pull the dishwasher out from under the counter.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Noisy
- See more...
Installation Instructions
kathleen from Kenner, LA
after unlatching dishwasher door fell open-- no resistence
Pull out dishwasher, removed old sleeves (was split), released spring mechanism, slipped on new sleeves, re attached spring mechanism, reset dishwasher.
Read more...
$68.77
In Stock
Dishwasher Door Gasket - Gray
Fix Number FIX11755809
Manufacturer Part Number WPW10509257
It provides a waterproof seal between the tub and the door.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Francis from Strykersville, NY
Dishwasher leaking at bottom of door
It was real easy to change the door seal after I watch the repair video.Only after i installed the new seal it leaked worse than before.After reading up on the problem iI decided to check the float it had crud in it and the Vent in the door was full of crud and build up. After cleaning them and freeing them up. The dishwasher works great. the seam and water have to have some where to go when the machine is running., if the float is plugged the washer will over fill. and if the vent in the upper door is plugged the water will be pushed out the bottom of the door and because the door had a new seal it made more water come through the bottom of the door because it had a tighter seal. hope this helps some one. this saved me from buying a new machine.
Read more...
$13.70
In Stock
Lower Sprayarm Seal
Fix Number FIX11741334
Manufacturer Part Number WP3376846
This genuine OEM seal fits under the lower spray arm in your dishwasher. It is also known as a bearing ring and is used to create a seal between the spray arm and the sump housing. The part measures approximately 2 inches in diameter, is made of a white plastic, and has been purposely designed with the split in the ring. No tools are required to replace the seal, simply remove the lower rack in the dishwasher and unscrew the nut holding the lower spray arm in place.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Glenn from GLENDALE, AZ
Lower sprayer arm was excessively loose and would sometimes tip so high that it would not allow the lower basket to be pulled forward..
Remove lower basket completely. Loosen plastic butterfly nut, (in my case only needed to use my hand) Remove spray arm, remove old seal, replace spray arm, put the bearing ring in place, install butterfly nut and tighten, (firm hand tight) DONE
Read more...
$91.96
In Stock
Dishwasher Drain Pump
Fix Number FIX11753379
Manufacturer Part Number WPW10348269
If there is still water left in your dishwasher after it has finished running, there may be an issue with your drain pump. The pump is designed to remove water from the tub, and if that is not happening then it could be due to damaged that is causing the motor not to run or a crack causing a leak. If a new pump is required, this is a genuine OEM replacement part. Completing this repair will be easiest if you pull the dishwasher out from under the cabinet. You will need to disconnect both the water and electrical supply to the appliance before starting.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
WILLIAM from MCKEES ROCKS, PA
Dishwasher not draining
This was one of the easiest jobs I ever did first I rremoved the excess water with a Shop-Vac then removed the kick plate two screws then removed the clamp from the drain hose pulled the electrical wiring off the pump removed the pump by turning it counterclockwise put the new pump in turning it clockwise it took less than a half-hour but a little more than 15 minutes
Read more...
Appliance Type
Related Pages
- Inglis Dishwasher Caps and Lids
- Inglis Dishwasher Dishracks
- Inglis Dishwasher Dispensers
- Inglis Dishwasher Hardware
- Inglis Dishwasher Hoses and Tubes
- Inglis Dishwasher Pumps
- Inglis Dishwasher Seals and Gaskets
- Inglis Dishwasher Spray Arms