This black rubber gasket is a genuine OEM replacement part for your dishwasher door. The gasket helps to provide a tight seal between the door and the tub, preventing water from leaking while the appliance is in use. Over time gaskets can become stretched out or brittle, and it should be replaced before a major leak happens. This kit also comes with a new latch strike plate for the door latch, which provides tension to ensure a tight seal.
Works with the following brands:
Whirlpool, Kenmore, Maytag, Amana
Works with the following products:
Dishwasher
Fixes the following symptoms:
Leaking, Not cleaning dishes properly, Door latch failure, Door won’t close
Part# W10542314 replaces these:
AP5650274, 2409202, W10542314, 8268888, W10284090, W10300589
...
Show more, W10350162, W10542314VP Show less
Works with the following brands:
Whirlpool, Kenmore, Maytag, Amana
Works with the following products
Dishwasher
Fixes the following symptoms
Leaking, Not cleaning dishes properly, Door latch failure, Door won’t close
Replacing your Dishwasher Door Gasket with Strike - Black
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched. Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Greg
October 12, 2021
Leaking from bottom of door - actually a substantial flow
For model number DU930PWSQ0
Hello Greg, Thank you for the question. We suggest waiting for the full cycle to complete and open the door. Check to see if the water is above the Element. If the water is above the element it is over filling and it will cause a leak. Make sure the Float is moving freely and the Float switch is tab can be activated once the float rises. We hope this helps!
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
Affresh dishwasher Cleaner is specially formulated to help remove limescale and mineral build-up that can be unsightly and could affect your dishwasher's performance. Each tablet is designed to clean inside your machine ...
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
It was news to me but a dishwasher needs to be cleaned periodically at least once per year. I watched a You tube video to get the basiscs for this dishwasher. The first step is to remove the upper racks. the two plastic end clips on the sling rails must be removed. 2. Remove the lower rack. 3. The third step is the water spinner. T
... Read morehis is done by holding the retaining nut with a pair of pliers and rotating the water spinner counterclockwise 4. Remove the water distribution system that conveys water to the upper rack by twisting it approx. 30 degrees clcckwise and lifting the bottom hub over the spinner assemby hub. This system is connected to the back and top of the dishwasher with retaing spring clips . 5 Next, remove the filter in the bottom of the dishwasher by using t20 star bit to remove 4 screws. 6. Use a smaller T bit to rove two scews holdin a flat retaining plate and the cover for the chopper assembly. 7. Remove chopper assem. housing by rpivoting housing up to the right . A screwdriver is needed. Clean all parts including dissassembly of the filter, the upper water distribution system etc. If you clean well and put it all back together, your dishwasher will clean again.
Small leak from dishwasher door - gasket falling apart near hinges
Removed old gasket. Checked for any dirt in the gasket slot. Folded gasket in half to find middle. Started at top and worked gasket into slot evenly from top to bottom with fingers. I then found that the door would not close completely and pop open. I carefully pushed the gasket further into the slot with a popsicle stick. The door
... Read morewould still pop open. I trimmed about 3/4" from each end of the gasket near each hinge and got the door to stay closed. It has worked well ever since. No leaks. I did not replace the latch. The existing metal latch was fine.
Easy install without the need for hand tools. You simply (1) remove the old gasket by pulling it off from the door frame, noting how it fit. (2) Clean the groove of any buildup of soap residue before installing the new gasket. (3) with your fingers, firmly press the gasket into the groove -- starting at the bottom and work your way around
... Read more the door's perimeter. (4) Test for leaks
Two things were wrong. one, there was a screw loose, and two, the gasket had a worn hole in it. The original gasket pulls off easily and the new one was installed in less than two minutes. The strike is metal so did not have to install the new one. There is a proper way to install the gasket based upon it's design so look at that carefu
... Read morelly before installation.
I removed the old gasket by pulling it out. I then cleaned off all the surfaces surrounding the area and made sure the groove was free of debris. I gently inserted the new gasket making sure I had it facing in towards the washing area and started both ends first, then worked my way to the top. Then once I saw it was in place and covering
... Read moreall the area I pressed firmly to secure it in the groove. I then ran a test on the unit to insure no leaking. My strike plate was metal and I did not replace it.
Ordered the part, read a few reviews, watched video, completed repair. Advise watching the video since people who reviewed mentioned "Cutting off excess". video repairman did a great job. I am 67 year old female and had no problem and used no tools.
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.