Amana Dishwasher Parts

Start With Your Model Number

Need help finding your model number?
Find Parts Fast
Guaranteed Fit
Repair Videos
Fix.com search
Amana Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular Amana Dishwasher Parts

Watch the install video
Dishwasher Door Seal – Part Number: W11177741
Dishwasher Door Seal
$56.05
In Stock
Fix Number
FIX12348515
Manufacturer Part Number
W11177741
Prevent leaks and maintain optimal cleaning performance with this durable dishwasher door seal. It creates a secure barrier to keep water contained during wash cycles, ensuring reliable operation. Replace by removing the old seal and fitting the new one snugly around the door frame.
Fixes these symptoms

Installation Instructions

A W from MENDOTA, IL
Started leaking under the door. The rubber door gasket appeared to be breaking down, very soft.
I soaked the new door gasket in warm soapy water while I removed the old gasket. This is the rubber seal inside the washer that closes off the sides and top of the door. Gently pulling on the old gasket removed it, then the new one slide right into place. Took about 5 minutes or less. Read more...
Circulation Pump – Part Number: W11612326
Circulation Pump
$76.45
In Stock
Fix Number
FIX16744934
Manufacturer Part Number
W11612326
If your dishwasher isn’t cleaning dishes properly or is making strange noises, the circulation pump might be the issue. This part helps move water through the spray arms during the wash and rinse cycles. A faulty pump can lead to leaks, poor cleaning, or leftover food particles. It’s a genuine replacement part and may need to be replaced if there’s a blockage, motor issue, or physical damage. Be sure to unplug your dishwasher before starting any repairs.
Fixes these symptoms
  • Leaking
  • Not cleaning dishes properly
  • Not draining
  • See more...
Watch the install video
Dishwasher Seal – Part Number: WPW10497235
Dishwasher Seal
$10.45
In Stock
Fix Number
FIX11755651
Manufacturer Part Number
WPW10497235
If your dishwasher has started leaking, there may be an issue with the door seal. This genuine OEM replacement part measures approximately 22 inches long and 2 inches wide. The seal is made of plastic and is found at the bottom of the dishwasher. It is used to provide a seal between the tub and the outer edge of the door to prevent leaking.
Fixes these symptoms

Installation Instructions

A W from MENDOTA, IL
Started leaking under the door. The rubber door gasket appeared to be breaking down, very soft.
I soaked the new door gasket in warm soapy water while I removed the old gasket. This is the rubber seal inside the washer that closes off the sides and top of the door. Gently pulling on the old gasket removed it, then the new one slide right into place. Took about 5 minutes or less. Read more...
Watch the install video
Dishwasher Rack Track Stop – Part Number: WP8565925
Dishwasher Rack Track Stop
$9.40
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX11746591
Manufacturer Part Number
WP8565925
This is a single rack track stop clip used to prevent the upper dish rack from sliding all the way out of the dishwasher. It is made of gray plastic and can wear with time. This is an easy repair that should not take very long to complete. Start by opening the dishwasher door, depress the tabs to remove both the front stop clips and remove the upper dish rack from the appliance. Now, using your small flat head screwdriver, release the retaining tab to remove the rear stop track that you are replacing, and pull the clip up to remove it. Install the new clip by inserting it into the support rail from the top and press it down to secure it in place.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...

Installation Instructions

Richard from Austin, TX
Wheels on original upper rack adjust fell off and end stops would not stay on.
Removed old end stops. Pulled rack out of machine. Carefully removed old adjusters. Snapped in new adjusters. Slid rack back into the runners. Clipped in the new end stops. Done. Read more...
Watch the install video
Dishwasher Heating Element – Part Number: W10703867
Dishwasher Heating Element
$77.95
In Stock
Fix Number
FIX9494999
Manufacturer Part Number
W10703867
The heater element is located in the bottom of the dishwasher. It is used to maintain the temperature of the water during the wash cycle and to dry the dishes afterwards. If your dishes are not coming out properly cleaned or dried, there may be an issue with your heater element. If you need a new part, this is a genuine OEM replacement. In order to complete this repair, you will need to disconnect the power supply to your dishwasher, remove the water inlet valve, and pull the dishwasher out from underneath the cabinet if applicable.
Fixes these symptoms
  • Leaking
  • Not cleaning dishes properly
  • Not drying dishes properly
  • See more...
Dishwasher Lower Spray Arm – Part Number: WPW10491331
Dishwasher Lower Spray Arm
$43.21
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX11755592
Manufacturer Part Number
WPW10491331
This is a lower spray arm for a dishwasher. The lower spray arm allows water to be spread evenly throughout the dishwasher tub with the proper force so dishes come out clean. This spray arm is gray in color and is about 20 inches long. You may need to replace this part if the water is not being distributed.
Fixes these symptoms
  • Leaking
  • Noisy
  • Not cleaning dishes properly
  • See more...
Watch the install video
Dishwasher Drain Pump – Part Number: WPW10348269
Dishwasher Drain Pump
$61.15
In Stock
Fix Number
FIX11753379
Manufacturer Part Number
WPW10348269
If there is still water left in your dishwasher after it has finished running, there may be an issue with your drain pump. The pump is designed to remove water from the tub, and if that is not happening then it could be due to damaged that is causing the motor not to run or a crack causing a leak. If a new pump is required, this is a genuine OEM replacement part. Completing this repair will be easiest if you pull the dishwasher out from under the cabinet. You will need to disconnect both the water and electrical supply to the appliance before starting.
Fixes these symptoms
  • Leaking
  • Noisy
  • Not cleaning dishes properly
  • See more...

Installation Instructions

WILLIAM from MCKEES ROCKS, PA
Dishwasher not draining
This was one of the easiest jobs I ever did first I rremoved the excess water with a Shop-Vac then removed the kick plate two screws then removed the clamp from the drain hose pulled the electrical wiring off the pump removed the pump by turning it counterclockwise put the new pump in turning it clockwise it took less than a half-hour but a little more than 15 minutes Read more...
Watch the install video
Dishwasher Mounting Bracket – Part Number: WP8269145
Dishwasher Mounting Bracket
$14.65
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX11745496
Manufacturer Part Number
WP8269145
The mounting bracket is used to secure the top part of your dishwasher to the underside of your counter or cabinet. If you have solid surface counters (granite, quartz, etc.) you will likely need to side mount your appliance, and this type of bracket is sold separately. It is important to properly secure your dishwasher, as it helps to keep it level, and prevents it from moving, shaking, or tilting forwards. This is an authentic OEM part, made entirely of metal, and approximately 3 inches in length. These mounting brackets are sold individually, however most dishwashers require at least two brackets to secure the appliance to the countertop. It is recommended to check and replace all brackets at the same time, as they tend to wear at the same rate. Attaching the mounting bracket to the top of the dishwasher is simple, and just requires a pair of needle nose pliers to bend the tabs into place. When it comes time to attach your dishwasher to the countertop, please note that you will need screws (sold separately), a screwdriver, and if this is the first time the brackets are being attached, you will also need to use a drill bit to make pilot holes for the screws.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...

Installation Instructions

julie from arroyo grande, CA
Mounting bracket broken. Upper rack wheel broken.
Upper Rack Wheel Assembly - This is a little time consuming (maybe 15 minutes), but easy. You will need to remove the entire upper rack assembly before replacing the wheels. After you remove rack assembly and the dishwasher from under the cabinet (see guidance below for brackets), you will see two hex head sheet metal screws with integral washers on the outside of the dishwasher holding the wheel assembly onto the dishwasher. Use the pliers to remove the screws and the old wheel assembly. Install the new wheel and mount assembly using the old screws since the wheel assembly doesn't come with the mounting screws. Mounting Bracket - Pretty easy. Remove port cover for both left & right mounting screws on inside of dishwasher. Remove the screws (if they haven't already fallen out). Careful - they will drop to the floor. Pull the dishwasher partially out from under the counter. Remove the old bracket(s) and install the new one(s). You will need pliers to bend the tabs over to secure them. For the Kenmore, you need to break off the longer end. Slide the dishwasher back under the counter and align the screw holes with the cabinet. I use masking tape to hold the screw on the screwdriver so it doesn't fall off when inserting into the screw hole in the cabinet. Use the flashlight to help see that the holes are aligned. Tighten the screw and you're done. Read more...
Watch the install video
Dishwasher Door Handle And Latch Assembly with Switch – Part Number: WPW10130695
Dishwasher Door Handle And Latch Assembly with Switch
$43.21
In Stock
★★★★★
★★★★★
22 Reviews
Fix Number
FIX11748729
Manufacturer Part Number
WPW10130695
This kit includes the black plastic handle (white handle is no longer available from the manufacturer), the latch, and two switches. The door handle and latch assembly is a simple on/off mechanism that prohibits the dishwasher from operating when the door is open. Symptoms of a faulty door handle and latch assembly include the door not latching properly, being unable to close the door, leaking during operation, and the dishwasher not starting. It is common for the door latch to break down due to material fatigue and/or continually slamming or opening the door quickly. This part measure roughly 5.5 inches wide, 1.5 inches high and 2.5 inches deep. This OEM kit is sold as a single part.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...

Installation Instructions

David from Martinsville, VA
Handle broke
Put new one in place and tightened screws. Very easy Read more...
Watch the install video
Door Balance Link Kit – Part Number: 8194001
Door Balance Link Kit
$28.79
In Stock
★★★★★
★★★★★
6 Reviews
Fix Number
FIX972325
Manufacturer Part Number
8194001
If your dishwasher door is not opening or closing properly, it may be time to install a new balance kit. This part helps to support the weight of the door as it opens and closes. You should also check on the condition of the door springs as well, as they work with the balance kit and may also need to be replaced when you do this repair. This genuine OEM parts kit includes two door balance links and two door balance mounts with wheels, which will replace both the left and righthand sides. If you do need to replace the springs, please note that these are sold separately and are not part of this kit. Installing the parts is a simple job, however you will need access to both sides of your dishwasher. This will require pulling it out from under your counter or cabinets. You will need a 5/16 nut driver to remove and replace the new balance mounts, and you may need a Philips screwdriver to remove the mounting hardware in order to pull your dishwasher out to work on. This kit can also be known as a door spring cable kit, or the door cable kit.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...

Installation Instructions

Rex from Fuquay-Varina, NC
Broken balance link nylon cord (cable) due to improper installation. Too much tension.
Looked at video and followed instructions. Be sure to set the link assembly at correct angle - follow what you see in video. The assembly should be straight up & down, not at an angle. Setting at angle causes too much tension on the nylon cord (cable) and makes the door hard to open and keeping in one position. Read more...

Amana Dishwasher Appliance Types

Related Amana Dishwasher Parts

Popular Amana Dishwasher Models

View More
+