KitchenAid Dishwasher Parts

KitchenAid Appliance Parts
Shop By Appliance Type

Popular KitchenAid Dishwasher Parts

$44.43
  In Stock
Dishwasher Lower Dishrack Wheel Assembly - Gray
★★★★★
★★★★★
(10)
Fix Number FIX11722152
Manufacturer Part Number W10195416V
This OEM gray plastic lower dishrack wheel assembly allows the rack to slide in and out of the dishwasher with ease. It measures roughly 3 by 6 inches. If it breaks or becomes damaged it may make sliding in and out feel difficult. This is a normal wear and tear item and will need to be replaced when this happens. It attaches directly to the dishrack and is a quick and easy repair. There are 4 dishrack wheel assemblies in total on your appliance, so this is a good time to inspect all 4, as this part is sold individually. To repair, open the dishwasher door and pull out the lower dishrack. Next, push the tab from both sides and it should pop out. To install the new wheel assembly, place it on the rack and make sure the caps overlap the wire from the inside before you clip it in place by pushing the wheel.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...
Installation Instructions
Anthony from Helena, MT
Wheels and hubs have melted and broken frequently
Easy to install. Snap right on to lower basket. Read more...
$31.82
  In Stock
Door Balance Link Kit
★★★★★
★★★★★
(5)
Fix Number FIX972325
Manufacturer Part Number 8194001
If your dishwasher door is not opening or closing properly, it may be time to install a new balance kit. This part helps to support the weight of the door as it opens and closes. You should also check on the condition of the door springs as well, as they work with the balance kit and may also need to be replaced when you do this repair. This genuine OEM parts kit includes two door balance links and two door balance mounts with wheels, which will replace both the left and righthand sides. If you do need to replace the springs, please note that these are sold separately and are not part of this kit. Installing the parts is a simple job, however you will need access to both sides of your dishwasher. This will require pulling it out from under your counter or cabinets. You will need a 5/16 nut driver to remove and replace the new balance mounts, and you may need a Philips screwdriver to remove the mounting hardware in order to pull your dishwasher out to work on. This kit can also be known as a door spring cable kit, or the door cable kit.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...
Installation Instructions
Rex from Fuquay-Varina, NC
Broken balance link nylon cord (cable) due to improper installation. Too much tension.
Looked at video and followed instructions. Be sure to set the link assembly at correct angle - follow what you see in video. The assembly should be straight up & down, not at an angle. Setting at angle causes too much tension on the nylon cord (cable) and makes the door hard to open and keeping in one position. Read more...
$13.68
  In Stock
Mounting Bracket
★★★★★
★★★★★
(1)
Fix Number FIX11745496
Manufacturer Part Number WP8269145
The mounting bracket is used to secure the top part of your dishwasher to the?underside?of your counter or cabinet. If you?have solid surface counters (granite, quartz, etc.) you?will?likely?need?to side mount your appliance, and this type of bracket is sold separately.?It is important to properly secure your dishwasher, as it helps to keep it level, and prevents it from moving, shaking, or tilting forwards.?This is an?authentic?OEM part, made entirely?of metal, and?approximately 3?inches in length.?These mounting brackets are sold individually, however most dishwashers?require?at least two brackets to secure the appliance to the countertop. It is recommended to check and replace all brackets at the same time, as they tend to wear at the same rate. ?Attaching the mounting bracket to the top of the dishwasher is simple, and just requires a pair of?needle nose?pliers?to bend the tabs into place. When it comes time to attach your?dishwasher?to the countertop, please note that you will?need?screws?(sold separately), a screwdriver, and if this is the first time the brackets are being?attached, you will also need to use a?drill bit?to?make pilot holes for the screws.??
Fixes these symptoms
Installation Instructions
julie from arroyo grande, CA
Mounting bracket broken. Upper rack wheel broken.
Upper Rack Wheel Assembly - This is a little time consuming (maybe 15 minutes), but easy. You will need to remove the entire upper rack assembly before replacing the wheels. After you remove rack assembly and the dishwasher from under the cabinet (see guidance below for brackets), you will see two hex head sheet metal screws with integral washers on the outside of the dishwasher holding the wheel assembly onto the dishwasher. Use the pliers to remove the screws and the old wheel assembly. Install the new wheel and mount assembly using the old screws since the wheel assembly doesn't come with the mounting screws. Mounting Bracket - Pretty easy. Remove port cover for both left & right mounting screws on inside of dishwasher. Remove the screws (if they haven't already fallen out). Careful - they will drop to the floor. Pull the dishwasher partially out from under the counter. Remove the old bracket(s) and install the new one(s). You will need pliers to bend the tabs over to secure them. For the Kenmore, you need to break off the longer end. Slide the dishwasher back under the counter and align the screw holes with the cabinet. I use masking tape to hold the screw on the screwdriver so it doesn't fall off when inserting into the screw hole in the cabinet. Use the flashlight to help see that the holes are aligned. Tighten the screw and you're done. Read more...
$32.54
  In Stock
Dishwasher Upper Rack Adjuster
★★★★★
★★★★★
(4)
Fix Number FIX11756150
Manufacturer Part Number WPW10546503
This dishrack adjuster attaches to the side of the top dishrack and fits both the left and ride side. If you are looking to replace both sides, you will need to order 2 of this part, as they are sold separately. It connects to the track, making it possible to move the rack in and out as well as raise up and down to accommodate different size items. If this part breaks, it may make it difficult for the rack to slide in and out with ease, in which case it will need to be replaced, as this can lead to further issues. For this repair, remove the upper rack from the dishwasher, detach the adjuster housing cover and then detach the front and rear adjuster support straps from the tines. Pry off the stop clip to detach the old adjuster. Align the new adjuster on the rack and snap the stop clip in place to secure it. Place the front and rear support straps back on. Position the adjuster housing and place the cover back on to secure. Place the rack back into the dishwasher.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...
$8.85
  In Stock
Tine Pivot
★★★★★
★★★★★
(2)
Fix Number FIX11748190
Manufacturer Part Number WPW10082853
Having adjustable?tines?in your dishwasher can be?very useful?to ensure your dishes are secure?during the wash cycle. The Tine Pivot?clip?helps to keep those moveable?tine?rows?in?place on your dish rack.??If you notice your dishes?are not?cleaning properly, it may be that your Tine Pivots are broken or?damaged and?should be replaced.?This part, also called a?tine?row pivot, is about 3 inches in length, made of plastic, and is found on the top rack of your dishwasher. Replacing the part?is an easy job, with no tools?required.?Ensure you have removed all dishes from the top rack before you begin this repair.?Release and lift out the damaged clip, line up the new one along the tines,?and snap into place.?With the new Tine Pivot in place, your?tine?rows should stay held in place, ensuring your dishes get cleaned properly.?This is a genuine OEM?part and?is sold individually.??
Fixes these symptoms
Installation Instructions
Susan from Paola, KS
Tine Pivot broke off, fell in bottom of dishwasher & part of it melted from heat of dishwasher; could not be used, had to be replaced
Snapped new one in place Read more...
$8.85
  In Stock
Rack Track Stop
Fix Number FIX11746591
Manufacturer Part Number WP8565925
This is a single rack track stop clip used to prevent the upper dish rack from sliding all the way out of the dishwasher. It is made of gray plastic and can wear with time. This is an easy repair that should not take very long to complete. Start by opening the dishwasher door, depress the tabs to remove both the front stop clips and remove the upper dish rack from the appliance. Now, using your small flat head screwdriver, release the retaining tab to remove the rear stop track that you are replacing, and pull the clip up to remove it. Install the new clip by inserting it into the support rail from the top and press it down to secure it in place.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Not cleaning dishes properly
  • See more...
Installation Instructions
Richard from Austin, TX
Wheels on original upper rack adjust fell off and end stops would not stay on.
Removed old end stops. Pulled rack out of machine. Carefully removed old adjusters. Snapped in new adjusters. Slid rack back into the runners. Clipped in the new end stops. Done. Read more...
$87.70
  In Stock
Dishwasher Drain Pump
Fix Number FIX11753379
Manufacturer Part Number WPW10348269
Fixes these symptoms
  • Leaking
  • Noisy
  • Not cleaning dishes properly
  • See more...
Installation Instructions
WILLIAM from MCKEES ROCKS, PA
Dishwasher not draining
This was one of the easiest jobs I ever did first I rremoved the excess water with a Shop-Vac then removed the kick plate two screws then removed the clamp from the drain hose pulled the electrical wiring off the pump removed the pump by turning it counterclockwise put the new pump in turning it clockwise it took less than a half-hour but a little more than 15 minutes Read more...
$39.21
  In Stock
Dishwasher Dish Rack Adjuster Kit - Left and Right Side
★★★★★
★★★★★
(39)
Fix Number FIX10064063
Manufacturer Part Number W10712394
This rack adjuster kit is connected to the dishrack and allows you to adjust the height of the upper rack of your dishwasher up and down to give more space. The kit is constructed of gray plastic and metal, and measures approximately 12 inches wide and 6.5 inches tall. This kit includes 2 adjuster arms, 2 adjuster actuators, 2 gray adjuster covers, 2 gray adjuster housings, and 4 screws. The rack adjuster can break from material fatigue or prolonged high temperature exposure, compromising the integrity of the materials. The most common indicators of a faulty rack adjuster include leaking, door latch failure, the door not closing, dishes not cleaning properly, and failure to start the wash cycle. This kit includes the parts to replace the left and right-side rack adjusters and has been upgraded to a more durable metal design. Replacing this part requires beginner repair experience, basic hand tools, and some disassembly of the dishwasher. Do not forget to unplug the dishwasher or shut off the water supply to the appliance underneath the sink before you begin.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...
Installation Instructions
Richard from New Hyde Park, NY
Rack wheels broken
Hardest part was figuring out that the rack adjuster kit fixed the problem. The new part is completely redesigned to correct problem of plastic part that causes the wheel failure. New part made of chrome should last a long time. Installation was easy. parts snap together and diagrams are easy to follow. took 1/2 hr. Read more...
$8.85
  In Stock
Rack Stop Clip
★★★★★
★★★★★
(2)
Fix Number FIX11750071
Manufacturer Part Number WPW10195622
The genuine OEM replacement rack stop clip is for dishwashers. It measures just over an inch and is made of gray plastic. The purpose of this part is to prevent your dishwasher rack from pulling out too far and falling out of the dishwasher. If you have difficulties closing your door, your rack continuously falling off, or a door latch failure, you may need to replace this part. They are sold individually and can be used on the right or left side of the upper dish rack. It is recommended to replace both sides at the same time, meaning you will need to order 2 of this part. For this easy repair, start by pulling out the rack, then use your screwdriver to reach behind the rack stops and push on the clips. This should allow you to remove the stops from the track. Next, slide the track back over the rollers and snap the new track stop in place.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Not cleaning dishes properly
  • See more...
Installation Instructions
JAMES from Waterloo, IA
The plastic clips were broken and old
I took out the old clips with a flat screwdriver and popped the new ones in. It took a min to see how to put them together and YOU HAVE TO PUT THE RAIL IN THE DISHWASHER FIRST! It is very tempting to just put the new part in but then you will have a hard time straddling the wheels inside the rail. Once you see how they fit and position them it is pretty easy to put them in once the rail is inside the washer and in place. These are the only ones I have ever had to replace. I suggest that you keep idiots that pull the top rack out too hard away from it so you do not have to spend 17 plus dollars on some plastic pieces to make your stuff work again. In my case I have co-workers that use it so I just put the part number on the magnet they gave me and the name of what it is called so that next time I will not have to be the one doing it. I could have went to the local parts place but they insisted I needed the exact model number and I had the one from the door but they said it was wrong. I was able somehow to use that number to pull pictures and this part from Google search so the hell with the local people I shopped here instead! The actual model # was in fact on the dishwasher where the door closes by the seal on the left side facing the front of it. It is only on there once while there are at least 2 stickers with the other number I pulled from the door in at least 2 languages. You tell me which is more needed..... yeah I did not need the model number as long as I had the sticker one. Ha Ha local losers at Dey Appliance can suck it! They always act like customers are interrupting them when you call or go in. Not anymore! Read more...
$8.44
  In Stock
Touch-Up Paint - White
Fix Number FIX385132
Manufacturer Part Number 72017
18ml
Installation Instructions
Al from Cape Coral, FL
No heat when trying to dry clothes .
Followed instructions on your videos. Everything went as planned and the dryer works like new.... Read more...

Appliance Type

Popular KitchenAid Dishwasher Models