Models > KUDC10FXSS5

KUDC10FXSS5 KitchenAid Dishwasher

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for KUDC10FXSS5

Viewing 12 of 12

Manuals & Guides for KUDC10FXSS5

Click to download
Keep searches simple, eg. "belt" or "pump".
This OEM gray plastic lower dishrack wheel assembly allows the rack to slide in and out of the dishwasher with ease. It measures roughly 3 by 6 inches. If it breaks or becomes damaged it may make slid...
Special Order
If your dishwasher door is not opening or closing properly, it may be time to install a new balance kit. This part helps to support the weight of the door as it opens and closes. You should also check...
In Stock
Order within the next 10 hrs and your part ships today!
The genuine OEM replacement rack stop clip is for dishwashers. It measures just over an inch and is made of gray plastic. The purpose of this part is to prevent your dishwasher rack from pulling out t...
In Stock
Order within the next 10 hrs and your part ships today!
The mounting bracket is used to secure the top part of your dishwasher to the underside of your counter or cabinet. If you have solid surface counters (granite, quartz, etc.) you will likely need to s...
In Stock
Order within the next 10 hrs and your part ships today!
If your dishwasher is not cleaning your dishes properly, is not draining, or is noisy while operating, there may be an issue with your chopper assembly. The chopper is used to mince up food particles ...
Special Order
If there is still water left in your dishwasher after it has finished running, there may be an issue with your drain pump. The pump is designed to remove water from the tub, and if that is not happeni...
In Stock
Order within the next 10 hrs and your part ships today!
$29.52
This is also called the 3rd-level spinner. This part works like a little spray arm at the top of your dishwasher.
In Stock
Order within the next 10 hrs and your part ships today!
$46.54
This is an authentic OEM replacement drawer track for the upper rack of your dishwasher. Also known as a rack slider bar, it helps to support the top rack and allows it to glide in and out of your dis...
In Stock
Order within the next 10 hrs and your part ships today!
If the upper rack of your dishwasher has become difficult to roll in and out, or it keeps getting jammed, you may need to replace one or more wheels. Over time the plastic can become brittle, or deter...
In Stock
Order within the next 10 hrs and your part ships today!
Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.
In Stock
Order within the next 10 hrs and your part ships today!
$64.71
Sold individually.
In Stock
Order within the next 10 hrs and your part ships today!
Sold individually. Used with the heating element.
In Stock
Order within the next 10 hrs and your part ships today!

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Problems and Symptoms for KUDC10FXSS5

Viewing 10 of 10
Not cleaning dishes properly
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Leaking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Door latch failure
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Not draining
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Noisy
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Door won’t close
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Not drying dishes properly
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will not fill with water
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will not dispense detergent
Fixed by these parts
Fixing Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
  • Customer:
    Scott from Fort Lauderdale, FL
  • Parts Used:
    8194001
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Replaced Hinge Link
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
621 of 651 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Andrew from Alexandria, VA
  • Parts Used:
    WPW10348269
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
dishwasher not draining after wash cycle
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.

First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
470 of 515 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Steve from Inver Grove Heights, MN
  • Parts Used:
    WPW10757217
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Loud grinding noise from water pump
Rather than remove the pump assembly - as an earlier post had done - I pulled the entire dishwasher out and laid it down on the floor. This allowed easy, direct access to the motor (that was the hard, messy part). From this point it was easy. Unplug the wiring, remove the retaining bolt, rotate the motor off the mounting brackets and pull it out. Then put the new one in. That was the easy part (about 15 minutes). The entire job took 2-and-a-half hours, most of which was taken in disconnecting, cleaning up and reconnecting the dishwasher. It's much quieter now.
218 of 239 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!