Models > KP2671

KP2671 KitchenAid Mixer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for KP2671

Viewing 2 of 2
Keep searches simple, eg. "belt" or "pump".
This is a genuine OEM worm following gear for your stand-up mixer. The gear is made of metal and is attached to the planetary shaft. This is an important part of the appliance as it helps to drive the...
In Stock
Sometimes referred to as a retaining clip, the retaining ring is used to hold the drum support roller onto the shaft in your dryer. The clip may need to be replaced if you find that your dryer is nois...
In Stock
This hub gear is a genuine OEM replacement part for your stand mixer. This kit includes both the beveled gear and attachment and is also referred to as a worm follower gear. This gear assists with the...
In Stock
$48.20
Sold individually.
In Stock
NOTE: This part has been upgraded from plastic to metal housing. Gasket is no longer available separately. ***Used with Stand Mixers.
In Stock
This assembly includes the black knob. Used with Stand Mixers.
In Stock
This part is used with the stand mixers attachments, as well as to hold the end cap to the front of the mixer.
In Stock
Used on Stand Mixers.
In Stock
This Stand Mixer Gear Grease lubricates the moving parts of the stand mixer.
In Stock
This part works in conjunction with the worm and bevel gear.
In Stock
This is a replacement bowl arm lift for your stand mixer. It raises and lowers the mixing arm in the bowl. It is made of white plastic and is sold individually. This part can also be known as the bowl...
In Stock
$34.41
This part is the replacement wire whip for your stand mixer. It is made of metal and is approximately 7 inches from top to bottom, and 5 inches from side to side. The wire whip is an attachment which ...
In Stock

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for KP2671

Viewing 2 of 2
Noisy
Fixed by these parts
Fixing
How to fix it
Touchpad does not respond
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Barry from Rowland Heights, CA
Parts Used:
W11086780
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
wouldnt turn beaters
removed metal strap around motor housing then remove the 4 screws holding top motor cover on, then removed the 4 screws that hold gear cover in place, remove long gear that is driven by the motor gear, then with ring pliers remove ring off long drive shaft and lift off worm gears. once all gears are removed --removed all the old grease ( do this to get all the metal shavings out from the failed gear) repace the grease in the gear housing and reassemble in reverse order
91 of 100 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
WES from BREVARD, NC
Parts Used:
WP9703680, W11192795, W11192795, W11200218
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Plastic gear housing in stand mixer fractured causing gears to crash
Removed four screws to remove main cover. Removed four more screws to remove fractured plastic gear housing cover. Removed retainer ring and slid two gears and dowel off main shaft. Lifted out remaining gear train and bearings, Removed all grease and metal chips from all components. Greased new gears and reassembled. Replaced plasti c gear housing cover with oreviously purchased die cast replacement part. Assembled main cover.
66 of 99 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Villa Rica, GA
Parts Used:
WP9706648
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Mixer speed was uncontrollable
Removed screw from back of mixer cover band and then removed the 4 side screws, lifted top off of mixer and removed screws from circuit board control switch, removing wires one at a time so as to install correctly. replaced screws in circuit board/control. Restored top of mixer replaced screws and the put cover band back on mixer.walla do ne
42 of 50 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!