Models
>
KG25H1XER5
KG25H1XER5 Whirlpool Mixer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for KG25H1XER5
Viewing 3 of 3
Keep searches simple, eg. "belt" or "pump".
$18.30
This is a genuine OEM worm following gear for your stand-up mixer. The gear is made of metal and is attached to the planetary shaft. This is an important part of the appliance as it helps to drive the...
In Stock
$7.88
Sometimes referred to as a retaining clip, the retaining ring is used to hold the drum support roller onto the shaft in your dryer. The clip may need to be replaced if you find that your dryer is nois...
In Stock
$22.09
This hub gear is a genuine OEM replacement part for your stand mixer. This kit includes both the beveled gear and attachment and is also referred to as a worm follower gear. This gear assists with the...
In Stock
$6.54
This is a genuine OEM Torx screw that measures 7-18 and 3/4-inch. The screw is sold individually and can be used in a variety of appliances. The star shaped head allows the screw to have more torque a...
In Stock
In Stock
$27.35
This wire whip attaches to your stand mixer and is used for whipping food products. It is made of metal wire and is one of several attachments that you can add to your mixer. If you attempt to start y...
In Stock
$60.08
NOTE: This part has been upgraded from plastic to metal housing. Gasket is no longer available separately.
***Used with Stand Mixers.
In Stock
$23.40
This part is used with the stand mixers attachments, as well as to hold the end cap to the front of the mixer.
In Stock
$27.59
This flat beater is used on stand mixers. It is dishwasher safe, however, should only be washed in the upper rack. The Flat Beater is used to mix batters and light doughs. Should the coating become da...
In Stock
This assembly includes the black knob. Used with Stand Mixers.
In Stock
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for KG25H1XER5
Viewing 5 of 5Noisy
Fixed by these parts
How to fix it
Touchpad does not respond
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Gas igniter glows, but will not light
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barry from Rowland Heights, CA
- Parts Used:
- W11086780
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
wouldnt turn beaters
removed metal strap around motor housing then remove the 4 screws holding top motor cover on, then removed the 4 screws that hold gear cover in place, remove long gear that is driven by the motor gear, then with ring pliers remove ring off long drive shaft and lift off worm gears. once all gears are removed --removed all the old grease (
... Read more
do this to get all the metal shavings out from the failed gear) repace the grease in the gear housing and reassemble in reverse order
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Lake Mills, WI
- Parts Used:
- WPW10170081, WPW10170080, WP9709231, W11086780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Mixer Made Very Bad Grinding Noise, And Would Skip While Making Bread Dough
1, Removed trim piece (1 screw) 2, removed cover (4 screws) 3, removed speed switch assembly (2 screws) 4, removed gear cover (4 screws) 5, removed and examined 2 worm gears for wear. Gear cover was badly cracked, don"t know if it was caused by a previous repair or by heat, as old cover is plastic. Received new parts and installed them
... Read more
, 2 bearings, 2 worm gears, 1 new cover of diecast metal and a new gasket. All repairs made with a #2 phillips screw driver. My wife then made bread, and it preformed flawlessly.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Villa Rica, GA
- Parts Used:
- WP9706648
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Mixer speed was uncontrollable
Removed screw from back of mixer cover band and then removed the 4 side screws, lifted top off of mixer and removed screws from circuit board control switch, removing wires one at a time so as to install correctly. replaced screws in circuit board/control. Restored top of mixer replaced screws and the put cover band back on mixer.walla do
... Read more
ne
Read less
Was this instruction helpful to you?
Thank you for voting!