Jenn-Air Dryer Parts

Fix Number

FIX2162266

Manufacturer Part Number

LA-1006

Pad has adhesive backing.

★★★★★

★★★★★

1 Review

Fix Number

FIX11741429

Manufacturer Part Number

WP338906

This genuine OEM part is a radiant flame sensor for your gas dryer. It is used to determine when the temperature of the igniter is hot enough to ignite the gas. Once the igniter is hot enough, it allows the valve to open to release the gas. This acts as a safety mechanism which prevents dangerous levels of gas from building up. If your dryer will not start, is not producing enough heat, not heating up at all, is taking too long to dry laundry, or is shutting off too soon, you may need to replace the radiant flame sensor. Please be sure to disconnect the power and gas supply to your dryer before beginning this repair.

Fix Number

FIX11743369

Manufacturer Part Number

WP660658

This clamp is used to secure the drive motor.

★★★★★

★★★★★

1 Review

Fix Number

FIX11742807

Manufacturer Part Number

WP53-0918

This dryer lint filter is a critical component designed to trap lint and debris from the exhaust air during drying cycles. Positioned within the lint trap housing, it helps maintain proper airflow, reduce drying time, and prevent lint buildup inside the dryer and exhaust duct. A clean and functional lint filter supports efficient drying performance and minimizes the risk of overheating or fire hazards. Common symptoms of a worn or clogged filter include extended drying times, lint on clothing, and incomplete drying. Replacement is straightforward and typically involves sliding the old filter out and inserting the new one into the designated slot. Regular maintenance and timely replacement help ensure safe and effective dryer operation.

★★★★★

★★★★★

3 Reviews

Fix Number

FIX2162282

Manufacturer Part Number

LA-1053

This kit comes with three separate thermal fuses and is usually used with clothes dryers that have a fan mounted on the motor shaft. Included within this kit is the high limit (Limit: 258) the gas high limit (Limit: 240) and the gas and electric high limit thermostat (Limit: 300).

★★★★★

★★★★★

2 Reviews

Fix Number

FIX334310

Manufacturer Part Number

279834

This OEM kit comes with two ignition coils (one three-terminal boost/hold coil, and one two-terminal secondary coil). Usually only one of them burns out, but you should replace them as a set as both have to be operational for the gas valve to open. The primary purpose of the part is to open the gas valve and allow the gas to enter the burner. This is a safety mechanism to make sure that there is never an unsafe buildup of gas inside the appliance. You will find the coils attached to the dryer gas valve. This is not an uncommon repair; it can fail due to normal material fatigue over time. To test your current parts, watch the burner, and if the igniter glows for a while and then shuts off without the gas is igniting, it usually means one of these coils is bad.

★★★★★

★★★★★

20 Reviews

Fix Number

FIX346995

Manufacturer Part Number

341241

This multi rib belt is an OEM replacement part for a dryer. It attaches to the drum, idler pulley, and motor pulley, and is responsible for spinning the drum. Over time, the belt can become frayed, brittle, and inflexible. If you can hear the motor running, but the drum does not turn, it is likely that the belt is broken. Other symptoms of a broken multi rib belt include unusual noises, failing to start, no heat, a burning smell, and an unresponsive touchpad. Depending on the model, you will find the belt by looking behind the front panel or under the main top of the dryer. This belt is 1/4-inches wide, has a length of 92-1/4-inches, and has four ridges and three groves on the belt. Each belt is sold separately.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX2162263

Manufacturer Part Number

LA-1003

This kit comes in two pieces: the catch and the clip.

Fix Number

FIX11740735

Manufacturer Part Number

WP31001747

Depending upon your model, this seal can be used on either the front or rear drum. The hi-temp adhesive is sold separately.

★★★★★

★★★★★

1 Review

Fix Number

FIX2162280

Manufacturer Part Number

LA-1044

Ensure your dryer performs at its best with this 4750-watt, 240-volt heating element kit. It’s responsible for producing the heat needed to dry laundry effectively. Common signs of a failing element include extended drying times or no heat during operation. To replace, unplug the dryer and use a putty knife, quarter-inch nut driver, and needle nose pliers. This part is sold individually and does not come with extra components.