Dryer Wheels and Rollers

Maintenance Kit

★★★★★

★★★★★

10 Reviews

This is an authentic drum support roller kit for 29-inch-wide dryers. It includes 1 belt, 2 roller wheels and an idler pulley. The parts in this kit allow the dryer to tumble properly by supporting the drum cylinder. The idler pulley provides the tension needed for a multi-ribbed belt. The belt attaches to the drum, idler pulley, and motor pulley. If these parts are damaged, it could cause loud noises such as squeaking and squealing while the drum is turning. These are normal wear parts and are best replaced as a kit to ensure optimal performance.

Drum Support Roller Kit

★★★★★

★★★★★

9 Reviews

This OEM drum support roller kit contains the parts needed to replace one roller on your dryer. This kit includes one drum roller and two bearings. Most dryers use two drum rollers, and it is recommended to change both at once for optimal performance. The drum support roller holds the drum in position while it spins on the support wheels. It rotates on the roller shaft located on the rear bulkhead. It may need to be replaced if your dryer is noisy, will not tumble, leaves marks on clothes, or will not start. This part is prone to wear and tear, and if broken will need to be replaced. This part measures roughly 3 inches in diameter and is made of plastic, metal, and rubber. Each kit is sold individually (two would be needed to replace both drum support rollers, which is recommended).

Dryer Drum Support Roller This drum support roller kit contains the parts needed to replace one roller on your dryer and is an OEM approved replacement part. This kit includes one drum roller and two bearings. Tri-rings are sold separately. The drum support roller holds the drum in position while it spins on the support wheels. Most dryers use two drum rollers, and it is recommended to change both at once to ensure proper drum rotation and even wear. A common symptom of a worn drum support roller is an unusually noisy dryer. This repair has been rated by customers as medium difficulty, and generally takes 30-60 minutes to complete. For your safety, you must disconnect the power, gas, and vent lines before you begin. For this repair you may need a nut driver, pliers, a screwdriver, and a wrench.

Idler Pulley

★★★★★

★★★★★

2 Reviews

Often referred to as a dryer belt tension pulley wheel, this idler pulley is an OEM approved replacement part for a variety of dryer models. The idler pulley puts tension on the drive belt, and if the idler pulley fails to put the proper amount of tension on the belt, the dryer will not spin. It is located on the dryer drum, around the tension pulley. If your appliance is noisy during operation, will not tumble, or will not start, you may need to replace this part. It is made of durable plastic and has a diameter of roughly 2-inches. This part also includes the hardware needed for replacement. Most of our customers found this repair to be medium difficulty, and required a Philips screwdriver, 1/4-inch nut driver, putty knife, small flat blade screwdriver, and needle nose pliers to get the job done.

Rear Drum Support Roller Kit

★★★★★

★★★★★

3 Reviews

This is a rear drum support roller kit for your dryer. The 2 rollers come with 4 tri-rings, and 1 palnut. We recommend that you replace both rollers at once. This kit stabilizes the drum cylinder, while letting the drum rotate on the support rollers. If you are having problems with your appliance during tumble mode, or if it is too noisy, you will need this kit. To complete this repair you will need a putty knife, Philips screwdriver and a 5/16 nut driver.

Blower Wheel with Clamp

★★★★★

★★★★★

3 Reviews

The blower wheel is responsible for blowing heat into the dryer drum, and out of the exhaust vent. If you notice that your dryer is taking too long to dry or is make unusually loud noises, it may be time to replace the blower wheel. This genuine OEM replacement part comes with a metallic clamp that holds the wheel in place. This part attaches to the drive motor shaft and can be accessed by removing the front panel of the dryer. Be sure to disconnect the power supply before beginning this repair.

Drum Support Roller

★★★★★

★★★★★

1 Review

If your dryer is not tumbling, takes a long time to dry, or is noisy while tumbling, it may be time to replace the drum support rollers. These hold the drum in place while it rotates, so if they have become worn it can make for a lot of noise while the machine is operating. This genuine OEM part is sold individually, however your dryer will have two support rollers. As they tend to wear at the same rate, we suggest replacing both at the same time. The tools needed to complete this repair include a putty knife, 5/16 nut driver, and a pair of pliers. Completing this repair requires removing the drum from the dryer to access the support rollers. Be sure to disconnect power to the appliance before beginning this repair.

Idler Pulley Wheel A dryer's idler pulley wheel serves to help the belt to rotate the drum.

Blower Housing with Blower Wheel

★★★★★

★★★★★

1 Review

***Please Note: This part is a substituted part by the manufacturer. It may appear different, but should still work with your appliance.

Drum Support Shaft - Rear Shaft with Right Hand Threads Shaft for dryer drum support roller. Rear shaft with left hand threads. Part is updated so nuts may need to be replaced as well on older dryers.