Admiral Dryer Wheels and Rollers

★★★★★

★★★★★

10 Reviews

Fix Number

FIX373087

Manufacturer Part Number

4392065

This is an authentic drum support roller kit for 29-inch-wide dryers. It includes 1 belt, 2 roller wheels and an idler pulley. The parts in this kit allow the dryer to tumble properly by supporting the drum cylinder. The idler pulley provides the tension needed for a multi-ribbed belt. The belt attaches to the drum, idler pulley, and motor pulley. If these parts are damaged, it could cause loud noises such as squeaking and squealing while the drum is turning. These are normal wear parts and are best replaced as a kit to ensure optimal performance.

★★★★★

★★★★★

3 Reviews

Fix Number

FIX347627

Manufacturer Part Number

349241T

This is a rear drum support roller kit for your dryer. The 2 rollers come with 4 tri-rings, and 1 palnut. We recommend that you replace both rollers at once. This kit stabilizes the drum cylinder, while letting the drum rotate on the support rollers. If you are having problems with your appliance during tumble mode, or if it is too noisy, you will need this kit. To complete this repair you will need a putty knife, Philips screwdriver and a 5/16 nut driver.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX334244

Manufacturer Part Number

279640

Often referred to as a dryer belt tension pulley wheel, this idler pulley is an OEM approved replacement part for a variety of dryer models. The idler pulley puts tension on the drive belt, and if the idler pulley fails to put the proper amount of tension on the belt, the dryer will not spin. It is located on the dryer drum, around the tension pulley. If your appliance is noisy during operation, will not tumble, or will not start, you may need to replace this part. It is made of durable plastic and has a diameter of roughly 2-inches. This part also includes the hardware needed for replacement. Most of our customers found this repair to be medium difficulty, and required a Philips screwdriver, 1/4-inch nut driver, putty knife, small flat blade screwdriver, and needle nose pliers to get the job done.

★★★★★

★★★★★

1 Review

Fix Number

FIX11741913

Manufacturer Part Number

WP37001042

If your dryer is not tumbling, takes a long time to dry, or is noisy while tumbling, it may be time to replace the drum support rollers. These hold the drum in place while it rotates, so if they have become worn it can make for a lot of noise while the machine is operating. This genuine OEM part is sold individually, however your dryer will have two support rollers. As they tend to wear at the same rate, we suggest replacing both at the same time. The tools needed to complete this repair include a putty knife, 5/16 nut driver, and a pair of pliers. Completing this repair requires removing the drum from the dryer to access the support rollers. Be sure to disconnect power to the appliance before beginning this repair.

Fix Number

FIX11753706

Manufacturer Part Number

WPW10359270

Replace the shaft of your left side drum support roller with this part from Whirlpool/Kenmore. This replacement shaft is 2-7/8 inches long. It is meant for use with many of Whirlpool/Kenmore's gas and electric clothes dryers that have been manufactured since 1965. Also known as Drum Roller Shaft.

Fix Number

FIX11753708

Manufacturer Part Number

WPW10359272

Shaft for dryer drum support roller. Rear shaft with left hand threads. Part is updated so nuts may need to be replaced as well on older dryers.

Fix Number

FIX11753705

Manufacturer Part Number

WPW10359269

Replace the shaft of your right side drum support roller with this part. This replacement shaft is 3-3/16 inches long, but does not require a washer or a nut.

Fix Number

FIX11753707

Manufacturer Part Number

WPW10359271

This shaft is for the front with right hand thread. Sold individually.

★★★★★

★★★★★

1 Review

Fix Number

FIX2052494

Manufacturer Part Number

56000

Part may differ in appearance, but functions same as original part.

Fix Number

FIX11742273

Manufacturer Part Number

WP40113601

This drum support roller bracket and shaft assembly is a little over two inches long. It is made of metal.