Inglis Dryer Parts

Inglis Appliance Parts
Shop By Appliance Type

Popular Inglis Dryer Parts

$16.60
  In Stock
Multi Rib Belt - 92-1/4"
★★★★★
★★★★★
(14)
Fix Number FIX346995
Manufacturer Part Number 341241
This multi rib belt is an OEM replacement part for a dryer. It attaches to the drum, idler pulley, and motor pulley, and is responsible for spinning the drum. Over time, the belt can become frayed, brittle, and inflexible. If you can hear the motor running, but the drum does not turn, it is likely that the belt is broken. Other symptoms of a broken multi rib belt include unusual noises, failing to start, no heat, a burning smell, and an unresponsive touchpad. Depending on the model, you will find the belt by looking behind the front panel or under the main top of the dryer. This belt is 1/4-inches wide, has a length of 92-1/4-inches, and has four ridges and three groves on the belt. Each belt is sold separately.
Fixes these symptoms
  • Heat stays on after drum has stopped
  • No heat or not enough heat
  • Noisy
  • See more...
Installation Instructions
carolyn from phila, PA
not spinning
follow the vidio Read more...
$20.14
  In Stock
Dryer Thermal Fuse
★★★★★
★★★★★
(13)
Fix Number FIX11741460
Manufacturer Part Number WP3392519
The dryer thermal fuse, also sometimes referred to as the thermal cut off or temperature fuse, is a 2 by 1/2-inch, white, plastic safety mechanism that halts the flow of electricity to the motor circuit when a dryer overheats. If the fuse is missing or broken, your dryer will not start. A thermal fuse fails when the exhaust temperature exceeds the fuse rating, that is when the temperature rises above the temperature that the fuse is intended to manage. This can be caused by the heating element shorting, a regulating thermostat or thermistor failure, or with a partially restricted exhaust vent. The fuse attaches to the blower wheel housing. It must be replaced when there is no longer continuity between the terminals. This is a one-time fuse, meaning it cannot be re-set. The replacement part features two 3/16-inch terminals. While performing this repair, we recommend checking to make sure all vents are cleared and vacuumed. This OEM part is sold individually.
Fixes these symptoms
  • Heat stays on after drum has stopped
  • No heat or not enough heat
  • Shuts off too soon
  • See more...
Installation Instructions
gary from apex, NC
dryer not heating
Checked the heating element and found a break in the heating coil. Decided to change the thermal fuse and the the cycling thermostat because of the age of the dryer. Read more...
$27.19
  In Stock
Dryer Cycling Thermostat
★★★★★
★★★★★
(6)
Fix Number FIX11741405
Manufacturer Part Number WP3387134
This thermostat is an OEM replacement part for a dryer. It is sold individually. It measures approximately 2-inches by 1.5-inches, is black and silver, and constructed of plastic and metal material. You will find this part attached to the blower wheel housing. Cycling thermostats continually cycle the heating element off and on to maintain a constant inner temperature inside the dryer. This particular cycling thermostat will turn the heating element off once the temperature reaches 155F and cycles back on once the internal temperature drops by 25F. Do not forget to unplug the power to the dryer before you begin this repair. Keep in mind that you will need to pull the dryer out from the wall because this repair will need to be done from the back of the appliance with the back panel removed.
Fixes these symptoms
  • No heat or not enough heat
  • Shuts off too soon
  • Takes too long to dry
  • See more...
Installation Instructions
gary from apex, NC
dryer not heating
Checked the heating element and found a break in the heating coil. Decided to change the thermal fuse and the the cycling thermostat because of the age of the dryer. Read more...
$6.32
  In Stock
Door Catch Kit
★★★★★
★★★★★
(9)
Fix Number FIX334230
Manufacturer Part Number 279570
This kit includes two door strikes, and three door catches, to service doors that have one or two catches. The strike is mounted on the body of the dryer, while the catch is mounted on the dryer door. These two parts work together to keep the dryer door shut while in operation. If your appliances lid will not close, or it will not start, it may be time to replace the door catch. If this part is malfunctioning, it should be replaced immediately, as it is not safe to run a dryer with the door not properly closed. This kit also comes with a set of instructions to help with the repair.
Fixes these symptoms
  • Door won’t close
  • Lid or door won’t close
  • No heat or not enough heat
  • See more...
Installation Instructions
jeffrey from Brookhaven, PA
Dryer would run, but not heat
Needed it running quick, so no diagnostics. Ordered one of everything that could fix problem (plus a new door catch). Tipped it onto it's back & popped the bottom cover off. Element, thermal cutoff, thermistor, and fuse. were right in front and held by 2 screws each (don't drop them, don't ask). A little bit tight inside, but no big issue. vacuumed the inside, replaced everything (it was the Heating Element, by the way), slapped the cover on, and put it back in its spot. works like it was new. Yes, I unplugged it first. Remember! Safety Third! Read more...
$48.62
  In Stock
Maintenance Kit
★★★★★
★★★★★
(7)
Fix Number FIX373087
Manufacturer Part Number 4392065
This is an authentic drum support roller kit for 29-inch-wide dryers. It includes 1 belt, 2 roller wheels and an idler pulley. The parts in this kit allow the dryer to tumble properly by supporting the drum cylinder. The idler pulley provides the tension needed for a multi-ribbed belt. The belt attaches to the drum, idler pulley, and motor pulley. If these parts are damaged, it could cause loud noises such as squeaking and squealing while the drum is turning. These are normal wear parts and are best replaced as a kit to ensure optimal performance.
Fixes these symptoms
  • Marks left on clothes
  • No heat or not enough heat
  • Noisy
  • See more...
Installation Instructions
Steve from South Lake Tahoe, CA
Defective heater element dryer still runs.
Expect to spend a lot of time on your knees. Unplug appliance. Remove dryer hose. remove back cover 4-6 7mm bolts. Unplug dryer heater element connections 2 blade or pin connectors. Unbolt element cover and remove old element. Label wires. Hopefully the replacement connections match if not go to hardware store. Crimp or better solder on new connectors. Install element in housing and reattach. Clean out all old dirt and lint. check old belt for wear and re-grease drum roller shafts. re-install back cover, hose and plug in. enjoy you just saved $600 Read more...
$19.44
  In Stock
Rear Drum Support Roller Kit
★★★★★
★★★★★
(3)
Fix Number FIX347627
Manufacturer Part Number 349241T
This is a rear drum support roller kit for your dryer. The 2 rollers come with 4 tri-rings, and 1 palnut. We recommend that you replace both rollers at once. This kit stabilizes the drum cylinder, while letting the drum rotate on the support rollers. If you are having problems with your appliance during tumble mode, or if it is too noisy, you will need this kit. To complete this repair you will need a putty knife, Philips screwdriver and a 5/16 nut driver.
Fixes these symptoms
  • Marks left on clothes
  • Noisy
  • Will Not Start
  • See more...
Installation Instructions
Tyrik from KENNESAW, GA
The roller support wheels were worn down and needed replacing.
Step 1: removed power source.
Step 2: removed screws from lent catcher.
Step 3: removed top lid.
Step 4: removed front panel.
Step 5: removed drum.
Step 6: removed plastic washers.
Step 7: removed old wheels.
Step 8: installed new wheels.
Reversed steps to put everything back.
Read more...
$7.48
  In Stock
Leveling Foot
Fix Number FIX1609293
Manufacturer Part Number 49621
Sold individually.
Fixes these symptoms
Installation Instructions
michael from Tampa, FL
Dryer had a very loud squealing sound
Remove 2 screws in the lint catcher push in on the clips in the front corners with a slim screwdriver to flip the top up then remove the two 5/16th bolts on either side to release the front of the dryer lifting slightly to remove the front then tilt dryer back so your not on the floor. Then remove the tension spring remove the bolt 3/8 remove the idler pully bracket then reverse to put back together after aligning the belt Read more...
$27.10
  In Stock
Dryer Door Switch
★★★★★
★★★★★
(10)
Fix Number FIX11741701
Manufacturer Part Number WP3406107
This OEM dryer door switch is an on/off mechanism that detects when the door is open to prevent the dryer from operating. If your dryer will turn on but will not start or continues working while the door is open, you may have a faulty door switch. This part features the switch and three wires, is white in color, and measures 6.5 inches long. This switch replaces the two-wire switch that is on many models. You will find this part attached to the inside of the top end of the front panel. One end attaches to the wiring harness and the other goes through the panel to make contact with the door when the door is closed. This is a regular wear part due to such frequent use or continuous harsh handling. Depending on how the switch broke, it might make it impossible to start or stop your drying cycle. You can test the function of this part by pushing on the black tab that sticks out of the front panel to make contact with the dryer door. If there is no resistance in the tab and it does not make a clicking sound, it likely needs to be replaced.
Fixes these symptoms
  • Door won’t close
  • No heat or not enough heat
  • Shuts off too soon
  • See more...
Installation Instructions
David from Delmar, DE
dryer door switch didn't work
Very easy, whirlpool replaced the 2 wire switch with a 3 wire switch. After calling this site, and Whirlpool about the new 3 wire harness, they said it would work fine, which it did. Read more...
$28.24
  In Stock
M Series New Style Coil Kit
★★★★★
★★★★★
(1)
Fix Number FIX334310
Manufacturer Part Number 279834
This OEM kit comes with two ignition coils (one three-terminal boost/hold coil, and one two-terminal secondary coil). Usually only one of them burns out, but you should replace them as a set as both have to be operational for the gas valve to open. The primary purpose of the part is to open the gas valve and allow the gas to enter the burner. This is a safety mechanism to make sure that there is never an unsafe buildup of gas inside the appliance. You will find the coils attached to the dryer gas valve. This is not an uncommon repair; it can fail due to normal material fatigue over time. To test your current parts, watch the burner, and if the igniter glows for a while and then shuts off without the gas is igniting, it usually means one of these coils is bad.
Fixes these symptoms
  • No heat or not enough heat
  • Noisy
  • Shuts off too soon
  • See more...
Installation Instructions
John from Warrington, PA
Dryer did not stay hot
To avoid the mistake I made, make sure you pop the small, square white plug towards the bottom left on the front of the dryer. This gives you a view into the heater so you can see if the igniter and other components are working. In our case, the heater would ignite and stay on for 5 minutes and then go out. As noted on this site, 50% of the time it is the gas coils so we tested them and they tested fine cold. However, testing all of the other electrical components and they tested out as well so we purchased the coil kit (again 50%). Following one of the many videos on the site, it was quite simple to get to the coils. Unplug and turn off the gas at the wall. Unscrew the two screws in the lint trap and pop up the lid with small flat screwdriver as there is a catch on each side under the lip in the front. With the top lid up, pull up and out on the front panel, the drum will stay in place but dip as you remove the front panel holding the drum in place. Reach under and to the right to remove the belt around the drum so you can remove the drum. The coils are right in front and are easily removed with a phillips screwdriver to remove the cap holding the coils. The coils are keyed and just slide out and into place. Replace the cap and reverse the steps. However, while you have the dryer apart, it is a good idea to remove all of the extra lint as we also did the same removing the back panel and the lint trap apparatus. We had quite the collection of lint and stuff in the blower that could never be removed without taking this apart so I highly suggest you take a look. It is about 10 phillips screws holding everything in place. With the coils in place, the dryer starts hot and stays hot. Repaired in under an hour and under $25 thanks to this site! Read more...
$61.70
  In Stock
Heating Element - 240V 5400W
★★★★★
★★★★★
(6)
Fix Number FIX334313
Manufacturer Part Number 279838
Sourced directly from the manufacturer, this heating element is an OEM approved replacement part for a variety of dryers and is sold individually. It measures approximately 10.5 inches long, 7.5 inches wide and 2 inches deep. The heating element is the primary source of heat used to dry the clothes in your dryer. This heating element is strung with a coiled wire made of a nickel and chrome alloy. It may need to be replaced if your dryer does not produce heat, if it produces too much heat, or if it will not turn on. If your dryer does not heat, first check for a blown thermal fuse on the blower housing before replacing the heating element. In most cases, the heating element will have a break in the element, making it defective. For this repair you will need a quarter inch nut driver and a pair of needle nose pliers. Start this repair by disconnecting the power and then remove the dryer vent. This repair is done from the back of the appliance with the back panel removed. With the panel removed, this will give you access to the heater element. Your next step is to remove the high-limit thermostat from the housing and remove the two wires from the heater terminals. Now remove the screws securing the element to the housing and slide the element out. Installation of the new part is done in the reverse order.
Fixes these symptoms
  • Heat stays on after drum has stopped
  • No heat or not enough heat
  • Shuts off too soon
  • See more...
Installation Instructions
gary from apex, NC
dryer not heating
Checked the heating element and found a break in the heating coil. Decided to change the thermal fuse and the the cycling thermostat because of the age of the dryer. Read more...

Appliance Type

Popular Inglis Dryer Models