Frigidaire Dryer Parts

Start With Your Model Number

Need help finding your model number?
Find Parts Fast
Guaranteed Fit
Repair Videos
Fix.com search
Frigidaire Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular Frigidaire Dryer Parts

Lint Filter – Part Number: 134793600
Lint Filter
$75.36
In Stock
Fix Number
FIX2349312
Manufacturer Part Number
134793600
This gray lint filter is used to collect lint and debris as it passes through the dryer vent. It is recommended to clean the lint filter before every load to clear the air flow through the lint filter. If your dryer takes too long to dry or the lint filter becomes damaged, you may need to replace the filter. This lint filter measures 14” wide and 11” high. This is a genuine OEM part.
Lint Filter Assembly – Part Number: 5304529766
Lint Filter Assembly
$81.11
Special Order
Fix Number
FIX16620745
Manufacturer Part Number
5304529766
This lint filter helps keep your Frigidaire dryer running smoothly by catching lint and debris during each cycle. If your old screen is damaged or clogged, swapping it out is a quick fix—just slide the new one into place. It fits many electric and gas models, and you might need to check your manual to see if the grille should be replaced too.
Belt – Part Number: 134719300
Belt
$57.30
In Stock
Fix Number
FIX2349294
Manufacturer Part Number
134719300
Fixes these symptoms
Watch the install video
Heating Element Assembly – Part Number: 131553900
Heating Element Assembly
$129.75
In Stock
Fix Number
FIX418120
Manufacturer Part Number
131553900
If your dryer has little to no heat, there may be an issue with your heating element assembly. The heater element is a genuine OEM part that is found at the back of the dryer. The heating element comes with a felt strip and insulators already attached. This part is used to provide heat in order to dry your laundry. It does this when the coil of nickel and chrome alloy wires resist the controlled electric current, and as a result the wires get hot. If you need to replace the heating element, please be sure to disconnect the power supply to your dryer before beginning this repair.
Fixes these symptoms

Installation Instructions

Jimmy from Mullins, SC
No heat
Watched the provided video and followed the written diagrams for my model dryer. Read more...
Dryer Heater Element – Part Number: 134792700
Dryer Heater Element
$116.11
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX2349309
Manufacturer Part Number
134792700
This 3-coil 5500 watts heating element with housing is used to produce heat to dry the clothes in your dryer. The heating element is strung with a coiled wired. The wire receives, but resists a controlled electric current causing the wire to heat up to dry your clothes. If there is no heat or it is taking too long to dry, you may need to replace the heating element. Check for a blown thermal fuse or thermal cut off. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.
Fixes these symptoms

Installation Instructions

ralph from EAST HAVEN, CT
dryer was shutting off in 4 minutes code e 64
watched u tube how to repaire code e64

took 15 minutes

you can do it Read more...
Watch the install video
Rear Drum Bearing Kit – Part Number: 5303281153
Rear Drum Bearing Kit
$42.85
In Stock
★★★★★
★★★★★
3 Reviews
Fix Number
FIX459829
Manufacturer Part Number
5303281153
This ball-and-socket style bearing kit is used in your dryer to support the rear of the drum as it tumbles through the dry cycle. The bearing attaches on the inside of the rear panel of the dryer cabinet. Over time, the bearing or the bushing can wear out, and the ball support can become damaged. If these things happen, your dryer may not tumble, or it will be noisy while operating. If this is the case, you may need to replace these parts. This genuine OEM parts kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high-temperature lubricant, and the installation screws. Completing this repair requires taking the entire drum out of your dryer along with handling greasy parts, so have a rag handy for cleanup. Please ensure that you disconnect the power supply to your appliance before beginning this repair.
Fixes these symptoms
  • Drum Not Spinning
  • Marks left on clothes
  • Noisy
  • See more...

Installation Instructions

Fred from San Antonio, TX
High pitched squeel while running dryer, replaced rear bearing, drive belt and front slider.
Followed the steps outlined in the video. Read more...
Watch the install video
Drum Glide - White – Part Number: 137513300
Drum Glide - White
$27.83
In Stock
Fix Number
FIX5574052
Manufacturer Part Number
137513300
Appliance requires 2 .Sold individually.
Fixes these symptoms

Installation Instructions

Robert from Derry, NH
Squeezing, clothes getting stuck.
This is a stacking washer & dryer. The best advice I read was to remove the door. It made the front panel much easier to remove. Removing the upper and lower felt was very easy. I used a sharp chisel to do this. Clothes clips worked great to hold the felts in place while the glue dried. The glides, yes you need 2 of them, just snapped out and back in with no problem. I also ended up replacing the drum bearing which was the cause of the squeezing. You will need a second set of hands to hold the bracket on the back side as the screws go on from the inside. I used an extra dab of grease to hold the grounding ball in place when I installed the bearing as well. Read more...
Watch the install video
Drum Support Bearing – Part Number: 131825900
Drum Support Bearing
$10.88
In Stock
Fix Number
FIX418807
Manufacturer Part Number
131825900
The drum support bearing is an authentic OEM replacement part for your dryer. The bearing is used to support the drum and allow it to rotate smoothly and quietly. If your dryer is excessively noisy while tumbling, will not start, will not tumble, or if it is leaving marks on your laundry, you may need to replace the drum support bearing. The bearing is found on the inside of the rear panel of the dryer cabinet, and you will need to remove the drum in order to complete this repair. Please be sure to disconnect the power supply to your dryer before you begin.
Fixes these symptoms

Installation Instructions

michael from Cave City, KY
browning clothes .zipper on jackets were tore off
after watching video and reading the review, whole job was simple Read more...
Watch the install video
Thermal Limiter - Limit 220 – Part Number: 134120900
Thermal Limiter - Limit 220
$13.07
In Stock
Fix Number
FIX419402
Manufacturer Part Number
134120900
This thermal fuse limiter is used in dryers to monitor the temperature and make sure it does not overheat. The thermal fuse has a limit of 220 degrees Fahrenheit before the heating element and power are cut off. If your thermal fuse has blown or is damaged then your dryer will not start, can over heat, or take too long to dry. It is important to replace the fuse to solve the above problems. For this repair, you will need a Philips screwdriver, putty knife, and a needle nose plier. As a safety precaution, remember to unplug dryer from power source to avoid electrocution when installing this part. Refer to the manual provided by the manufacturer for further instructions.
Fixes these symptoms

Installation Instructions

Jimmy from Mullins, SC
No heat
Watched the provided video and followed the written diagrams for my model dryer. Read more...
Watch the install video
High Limit Thermostat – Part Number: 3204267
High Limit Thermostat
$55.18
In Stock
Fix Number
FIX446428
Manufacturer Part Number
3204267
The two-terminal high limit thermostat has a limit of 260 degrees Fahrenheit and acts as a safety mechanism that keeps the dryer from overheating. The thermostat will cut out when the internal dryer temperature reaches 260 and then cuts back in when the temperature drops by 70 degrees Fahrenheit. If your dryer is not heating, you may need to replace the thermostat. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting your repair.
Fixes these symptoms

Installation Instructions

James from Palm Coast, FL
No Heat and error on front panel after about 2 minutes after running
removed 2 rear screws, removed top panel. Removed 2 top screws and 2 internal screws, disconnected electrical connections and removed front panel. removed drum guide. Disconnected drive belt, removed drum. removed 4 screws from rear, removed the heating element assembly. Cleaned the entire bottom section of the dryer. Installed new heating element assembly, installed thermal limiter and control thermistor, reassembled the dryer. Dryer has been working great! Read more...

Frigidaire Dryer Appliance Types

Related Frigidaire Dryer Parts

Popular Frigidaire Dryer Models

View More
+