Drum Glide - White
$
40.81
In Stock


Fix Number: FIX5574052
Manufacturer #: 137513300
Manufactured by:
Frigidaire
-
Product Description
Appliance requires 2 .Sold individually.
-
Works with the following brandsFrigidaire, Kenmore, Westinghouse, Crosley
-
Works with the following productsDryer, Washer Dryer Combo
-
Fixes the following symptomsNoisy, Marks left on clothes, Will not tumble
-
Part Number Cross ReferencePart# 137513300 replaces these:AP5650542, 2629362, 137513300, 131963900

Product Description
Appliance requires 2 .Sold individually.
-
Works with the following brands:Frigidaire, Kenmore, Westinghouse, Crosley
-
Works with the following products:Dryer, Washer Dryer Combo
-
Fixes the following symptoms:Noisy, Marks left on clothes, Will not tumble
-
Part# 137513300 replaces these:AP5650542, 2629362, 137513300, 131963900

Installation Instructions Provided by Fix customers like you.
Average Repair Rating: 3.1 / 5.0, 7 reviews.
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
-
Customer:Aron from Morley, MI
-
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
The seal went bad from my shirt buttons
Just like the video.. ( thanks ). I will buy from you again....
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Robert from Derry, NH
-
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers
Squeezing, clothes getting stuck.
This is a stacking washer & dryer. The best advice I read was to remove the door. It made the front panel much easier to remove. Removing the upper and lower felt was very easy. I used a sharp chisel to do this. Clothes clips worked great to hold the felts in place while the glue dried. The glides, yes you need 2 of them, just snapped out and back in with no problem. I also ended up replacing the drum bearing which was the cause of the squeezing. You will need a second set of hands to hold the bracket on the back side as the screws go on from the inside. I used an extra dab of grease to hold the grounding ball in place when I installed the bearing as well.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Jeremy from Harrisburg, PA
-
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
glide broke which ripped off the felt. Led to clothes being ruined
I first removed the top of dryer. Then I unscrewed the 2 mounting screws before undoing the front section . I removed the front section then used a cordless drill w/ the stripping wheel to remove all the remaining felt and glue residue. Finally I finished by the steps of the instruction video.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Thomas from Roaring Spring, PA
-
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
The rear drum bearing back holding bracket fell off and unit is built into wall.
Replacing the rear drum bearing "back of machine bracket" without moving the unit - if it drops off the back. 1. Remove all equipment except for the heating element and housing. 2. Start to remove the bearing cradle and mounting bracket but this is what to do if "you drop the back bracket as I did." 3. After everything is removed from the center back you will see a slop where the metal cradle mounts just below the screw holes and the center hole. 4. Take a piece of thin but strong thread - as nylon - approx. 2' long and just double it. 5. Push the loop end (open ends toward you) through the center hole so you can see it moving through the slot and use any thin instrument to "fish" the loop end through to yourself. 6. Now make sure you have your new kit parts, nut driver, awl, mounting screws, laid out in front of you for easy access. 7. Take the rear mounting bracket (with the 2 holes in it and center tab) and wrap 2 turns of the loop around the center tab while you still have the ends of the thread through the center hole next to you. You can tie one loop if you want - it just makes it harder to take out later but that is ok. 8. Now you are ready to pull the mounting bracket through the slot up to the center hole. It should be now directly centered. 9. Adjust hole and put one screw loosely in while still holding the bracket in place with the thread (keep tight), then tighten the screw tight. 9. Now you are ready to put the cradle, bearing, front mounting bracket (as per video instructions) in place on the open end where the hole is aligned. 10. Tighten the screw snug but still letting you able to move the bracket toward the screw that was holding the back bracket in place. 11. Loosen that screw into place and if needing adjusted - use the awl and finish aligning and installing. 12. Cut the thread and or unloosen and take out. Everything should now be ready for re installation of all other equipment. Wish you the best.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Kenneth from New london, CT
-
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
sqeaky noisy dryer
Start by unplugging dryer safety first , take off top and remove front control panel and wires take pics to be safe ! Next take off front panel it will allow you to move drum out enough to get to rear bearing assembly put in new bearing assembly coat riding surface with grease that comes with dont over do it! Assemble all back in reverse order your done!! You just saved yourself from getting ripped off by the repair man trust me its a very easy repair good luck!!
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Donald from SPRINGVILLE, IN
-
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
squeacky drum
remove control panel,unplug door switch connector,removedryer door assembly,unhook belt from tensioner,lift druum out of drum bearing and remove drum. change therear bearing,using bearing grease to retain the small ball bearing in the back of thedrum bearing during assembly. reverse for reassembly.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Kristen from Wyoming, RI
-
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
My dryer sounded like there were sneakers in it!!!
Well first I would like to say thank you so much for the great instructional videos! the only reason I put that it was a bit difficult was because my dryer and washer are built into an area that has a counter top built over the top so it was tough to get to. I followed the instructions on the video and fixed it all by myself. Parts were delivered in a day and a half awesome !!!!! saved me a lot of money, thanks again !
Was this instruction helpful to you?
Thank you for voting!

This part works with the following models:
Fix Number: FIX5574052
Manufacturer Part Number: 137513300
Manufacturer Part Number: 137513300
Brand
Model Number
Description