Gibson Dryer Parts

Start With Your Model Number

Need help finding your model number?
Find Parts Fast
Guaranteed Fit
Repair Videos
Fix.com search
Gibson Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular Gibson Dryer Parts

M Series Ignition Coil Kit – Part Number: 5303931775
M Series Ignition Coil Kit
$27.28
In Stock
Fix Number
FIX470049
Manufacturer Part Number
5303931775
This coil ignition kit is used in dryers to open the gas valve when the dryer is on. This kit includes two coils. One is a two-wire secondary coil and the other is a three-wire booster coil. If your dryer does not heat or you notice heating inconsistencies, then the gas valve may be damaged and it is best to replace it to solve this problem. To repair, first release the two retaining clips that hold the top panel in place, then remove two screws that retain the front panel of the dryer cabinet. Next, pull the front panel forward and remember to disconnect the door switch. After accessing the gas coils, start removing the wires and unscrew the bracket that holds the coils. Remember to remove both the dual and main coil without removing the spacer. For more information on the kit and repair instructions, refer to diagram for a list of the parts.
Fixes these symptoms

Installation Instructions

Miguel from Hialeah, FL
Not heating, Not Drying
I opened the dryer with instructions from Youtube, and look for the parts that I thought had the problem: Flame sensor and Ignition Coil Kit. Put dryer back together and turned on, it works like a champ, :-) I requested a repairman from Sears and he told me to just buy a new one, because the part needed cost $459.00, but for some reason it made no sense to me, so I went to this site and put the model number of my dryer and the problem, and they suggested that I replace the flame sensor. Miguel Read more...
Watch the install video
Drum Glide - White – Part Number: 137513300
Drum Glide - White
$27.83
In Stock
Fix Number
FIX5574052
Manufacturer Part Number
137513300
Appliance requires 2 .Sold individually.
Fixes these symptoms

Installation Instructions

Aron from Morley, MI
The seal went bad from my shirt buttons
Just like the video.. ( thanks ). I will buy from you again.... Read more...
Watch the install video
Blower Housing with Blower Wheel – Part Number: 131775600
Blower Housing with Blower Wheel
$107.13
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX418726
Manufacturer Part Number
131775600
If your dryer’s taking forever to dry clothes or making strange noises, the blower wheel might be the problem. This white plastic part helps push air through the drum and out the exhaust. It fits Kenmore 471 series dryers and some models from Frigidaire, Crosley, Gibson, and White Westinghouse. It’s a genuine replacement part, and before you start the repair, make sure to unplug your dryer and check that it matches your model.
Fixes these symptoms

Installation Instructions

lawrence from greensburg, KY
NOISY
was very easy. but have had a lot of them apart. remove top .take panel off back to reach the belt. remove the frount. remove the drum, removed vent hose. remove the old blower. and then put everything back just like it come apart. it's not bad.just take's time. Read more...
Watch the install video
High Limit Thermostat – Part Number: 3204267
High Limit Thermostat
$55.18
In Stock
Fix Number
FIX446428
Manufacturer Part Number
3204267
The two-terminal high limit thermostat has a limit of 260 degrees Fahrenheit and acts as a safety mechanism that keeps the dryer from overheating. The thermostat will cut out when the internal dryer temperature reaches 260 and then cuts back in when the temperature drops by 70 degrees Fahrenheit. If your dryer is not heating, you may need to replace the thermostat. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting your repair.
Fixes these symptoms

Installation Instructions

James from Palm Coast, FL
No Heat and error on front panel after about 2 minutes after running
removed 2 rear screws, removed top panel. Removed 2 top screws and 2 internal screws, disconnected electrical connections and removed front panel. removed drum guide. Disconnected drive belt, removed drum. removed 4 screws from rear, removed the heating element assembly. Cleaned the entire bottom section of the dryer. Installed new heating element assembly, installed thermal limiter and control thermistor, reassembled the dryer. Dryer has been working great! Read more...
Watch the install video
Front Lower Drum Seal – Part Number: 5303283286
Front Lower Drum Seal
$46.81
Special Order
Fix Number
FIX460194
Manufacturer Part Number
5303283286
This part helps to keep the dryer running as quietly as possible.
Fixes these symptoms

Installation Instructions

michael from Cave City, KY
browning clothes .zipper on jackets were tore off
after watching video and reading the review, whole job was simple Read more...
Watch the install video
Thermal Limiter - Limit 220 – Part Number: 134120900
Thermal Limiter - Limit 220
$13.07
In Stock
Fix Number
FIX419402
Manufacturer Part Number
134120900
This thermal fuse limiter is used in dryers to monitor the temperature and make sure it does not overheat. The thermal fuse has a limit of 220 degrees Fahrenheit before the heating element and power are cut off. If your thermal fuse has blown or is damaged then your dryer will not start, can over heat, or take too long to dry. It is important to replace the fuse to solve the above problems. For this repair, you will need a Philips screwdriver, putty knife, and a needle nose plier. As a safety precaution, remember to unplug dryer from power source to avoid electrocution when installing this part. Refer to the manual provided by the manufacturer for further instructions.
Fixes these symptoms

Installation Instructions

Jimmy from Mullins, SC
No heat
Watched the provided video and followed the written diagrams for my model dryer. Read more...
Watch the install video
Lower Front Felt Seal with Adhesive – Part Number: 5303937183
Lower Front Felt Seal with Adhesive
$32.12
In Stock
Fix Number
FIX832645
Manufacturer Part Number
5303937183
Fixes these symptoms

Installation Instructions

Aron from Morley, MI
The seal went bad from my shirt buttons
Just like the video.. ( thanks ). I will buy from you again.... Read more...
Watch the install video
Rear Drum Bearing Kit – Part Number: 5303281153
Rear Drum Bearing Kit
$42.85
In Stock
★★★★★
★★★★★
3 Reviews
Fix Number
FIX459829
Manufacturer Part Number
5303281153
This ball-and-socket style bearing kit is used in your dryer to support the rear of the drum as it tumbles through the dry cycle. The bearing attaches on the inside of the rear panel of the dryer cabinet. Over time, the bearing or the bushing can wear out, and the ball support can become damaged. If these things happen, your dryer may not tumble, or it will be noisy while operating. If this is the case, you may need to replace these parts. This genuine OEM parts kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high-temperature lubricant, and the installation screws. Completing this repair requires taking the entire drum out of your dryer along with handling greasy parts, so have a rag handy for cleanup. Please ensure that you disconnect the power supply to your appliance before beginning this repair.
Fixes these symptoms
  • Drum Not Spinning
  • Marks left on clothes
  • Noisy
  • See more...

Installation Instructions

Fred from San Antonio, TX
High pitched squeel while running dryer, replaced rear bearing, drive belt and front slider.
Followed the steps outlined in the video. Read more...
Watch the install video
Heating Element Assembly – Part Number: 131553900
Heating Element Assembly
$129.75
In Stock
Fix Number
FIX418120
Manufacturer Part Number
131553900
If your dryer has little to no heat, there may be an issue with your heating element assembly. The heater element is a genuine OEM part that is found at the back of the dryer. The heating element comes with a felt strip and insulators already attached. This part is used to provide heat in order to dry your laundry. It does this when the coil of nickel and chrome alloy wires resist the controlled electric current, and as a result the wires get hot. If you need to replace the heating element, please be sure to disconnect the power supply to your dryer before beginning this repair.
Fixes these symptoms

Installation Instructions

Jimmy from Mullins, SC
No heat
Watched the provided video and followed the written diagrams for my model dryer. Read more...
Watch the install video
Door Catch – Part Number: 131658800
Door Catch
$55.18
In Stock
Fix Number
FIX418433
Manufacturer Part Number
131658800
This door catch is an authentic OEM replacement part for your dryer. This part holds the door strike and ensures that the door stays closed while your dryer is running. This prevents hot air or laundry from escaping from the dryer. If your dryer will not start or the door will not stay closed, you may need to replace the door catch. Please be sure to disconnect the power supply to your dryer before beginning this repair.
Fixes these symptoms

Installation Instructions

Steve from Little Falls, MN
Broken door catch
Grab it with a pliers, jerk it out of the hole. Insert the new one. Easy Peasy, lemon squezy. Read more...

Gibson Dryer Appliance Types

Related Gibson Dryer Parts

Popular Gibson Dryer Models

View More
+