M Series Ignition Coil Kit

$ 28.23

Fix Number: FIX470049

Manufacturer #: 5303931775

Manufactured by: Frigidaire

Product Description

This coil ignition kit is used in dryers to open the gas valve when the dryer is on. This kit includes two coils. One is a two-wire secondary coil and the other is a three-wire booster coil. If your dryer does not heat or you notice heating inconsistencies, then the gas valve may be damaged and it is best to replace it to solve this problem. To repair, first release the two retaining clips that hold the top panel in place, then remove two screws that retain the front panel of the dryer cabinet. Next, pull the front panel forward and remember to disconnect the door switch. After accessing the gas coils, start removing the wires and unscrew the bracket that holds the coils. Remember to remove both the dual and main coil without removing the spacer. For more information on the kit and repair instructions, refer to diagram for a list of the parts.
Works with the following brands

Frigidaire, Kenmore, Gibson, Westinghouse
Works with the following products
Dryer, Washer Dryer Combo
Fixes the following symptoms

No heat or not enough heat, Takes too long to dry
Part Number Cross Reference

Part# 5303931775 replaces these:

AP2150379, 3449, 5303931775, 08015679, 08015680, 3201243, 3201244, 3281142, 3281143, 5300622602, 5303307291, 5303307292, 5308015680, 8015679, 8015680, F140570-300, F140570-400, G140570-300, G140570-400, Q000622601 ... Show more , Q000622602, Q622601, Q622602, WQ622601, WQ622602 Show less

0 Installation Instruction

Model Compatibility

Product Description Installation Instructions Model Compatibility

Product Description

This coil ignition kit is used in dryers to open the gas valve when the dryer is on. This kit includes two coils. One is a two-wire secondary coil and the other is a three-wire booster coil. If your dryer does not heat or you notice heating inconsistencies, then the gas valve may be damaged and it is best to replace it to solve this problem. To repair, first release the two retaining clips that hold the top panel in place, then remove two screws that retain the front panel of the dryer cabinet. Next, pull the front panel forward and remember to disconnect the door switch. After accessing the gas coils, start removing the wires and unscrew the bracket that holds the coils. Remember to remove both the dual and main coil without removing the spacer. For more information on the kit and repair instructions, refer to diagram for a list of the parts.

Works with the following brands:

Frigidaire, Kenmore, Gibson, Westinghouse
Works with the following products:
Dryer, Washer Dryer Combo
Fixes the following symptoms:

No heat or not enough heat, Takes too long to dry
Part# 5303931775 replaces these:

AP2150379, 3449, 5303931775, 08015679, 08015680, 3201243 ... Show more , 3201244, 3281142, 3281143, 5300622602, 5303307291, 5303307292, 5308015680, 8015679, 8015680, F140570-300, F140570-400, G140570-300, G140570-400, Q000622601, Q000622602, Q622601, Q622602, WQ622601, WQ622602 Show less

Installation Instructions Provided by Fix customers like you.

Average Repair Rating: 3.9 / 5.0, 11 reviews.

< Prev
1
2
3
Next >

Sort by:

Customer:

Miguel from Hialeah, FL
Parts Used:
5303931775, 5303281135
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

Not heating, Not Drying

I opened the dryer with instructions from Youtube, and look for the parts that I thought had the problem: Flame sensor and Ignition Coil Kit. Put dryer back together and turned on, it works like a champ, :-) I requested a repairman from Sears and he told me to just buy a new one, because the part needed cost $459.00, but for some reason it made no sense to me, so I went to this site and put the model number of my dryer and the problem, and they suggested that I replace the flame sensor. Miguel

2 of 2 people found this instruction helpful.