International Dryer Parts

★★★★★

★★★★★

10 Reviews

Fix Number

FIX1570070

Manufacturer Part Number

12001541

This OEM drum support roller kit contains the parts needed to replace one roller on your dryer. This kit includes one drum roller and two bearings. Most dryers use two drum rollers, and it is recommended to change both at once for optimal performance. The drum support roller holds the drum in position while it spins on the support wheels. It rotates on the roller shaft located on the rear bulkhead. It may need to be replaced if your dryer is noisy, will not tumble, leaves marks on clothes, or will not start. This part is prone to wear and tear, and if broken will need to be replaced. This part measures roughly 3 inches in diameter and is made of plastic, metal, and rubber. Each kit is sold individually (two would be needed to replace both drum support rollers, which is recommended).

★★★★★

★★★★★

3 Reviews

Fix Number

FIX1804752

Manufacturer Part Number

306508

This part is located on the front bulkhead of the dryer and helps the drum to rotate smoothly and quietly. If you notice a screeching or metal-on-metal noise while your appliance is operating, you may need to replace the front glides. This genuine OEM front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. We recommend replacing both sets of glides at the same time, which will require the purchase of two kits. To complete this repair, you will need a Philips screwdriver and a 5/16 nut-driver to remove the front panel and the bulkhead of the dryer, a drill with a 1/8-inch bit to remove the old rivets, and a rivet tool to install the new ones. Please ensure that you disconnect the power supply to your dryer before beginning this repair. While you have the appliance opened, we recommend vacuuming out any lint and debris, and inspecting the felt around the bulkhead and replacing if necessary.

★★★★★

★★★★★

9 Reviews

Fix Number

FIX11757542

Manufacturer Part Number

WPY312959

This is a single OEM dryer drum belt. It measures 100 inches in length, 3/8 of an inch wide and has five ribs and four grooves. Keep in mind that this rubber drum belt will stretch over time, so if you are comparing your current belt to these specified measurements, they may not be exact. For this repair, you will need to disconnect the power, and remove the front panel and drum. You will need a 5/16 nut driver and a stubby Phillips screwdriver. While you are doing this repair, be careful not to let the belt fall into the groove in the drum, causing it to be too loose.

Fix Number

FIX11743031

Manufacturer Part Number

WP6-3129480

The roller shaft is also known as a support roller shaft or a drum roller axle. It is a part in your dryer that the drum rollers spin on, helping your dryer to tumble. If your appliance is noisy while operating, or will not tumble at all, you may need to replace the roller shaft. You may also want to inspect the drum rollers at the same time and replace them if necessary. Replacing the roller shaft will require that you remove the front panel and the drum from the dryer. Please ensure that you disconnect the power supply before beginning this project. The tools you will need include a Philips screwdriver, a 5/16-inch nut driver, a pair of snap-ring pliers, and a 9/16-inch wrench. The roller shaft is an authentic OEM part.

★★★★★

★★★★★

3 Reviews

Fix Number

FIX2200270

Manufacturer Part Number

Y303836

The blower wheel is responsible for blowing heat into the dryer drum, and out of the exhaust vent. If you notice that your dryer is taking too long to dry or is make unusually loud noises, it may be time to replace the blower wheel. This genuine OEM replacement part comes with a metallic clamp that holds the wheel in place. This part attaches to the drive motor shaft and can be accessed by removing the front panel of the dryer. Be sure to disconnect the power supply before beginning this repair.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX11741110

Manufacturer Part Number

WP33002535

If your dryer is noisy while operating, or will not tumble at all, there may be an issue with the drum belt. Over time, the rubber can become brittle and snap, and the belt will need to be replaced. This genuine OEM multi rib dryer drum belt measures approximately 91 and 5/8-inch in length and is 3/8-inch wide. It is made of black rubber and have five ridges, helping it to grip to your dryer drum.

★★★★★

★★★★★

1 Review

Fix Number

FIX334310

Manufacturer Part Number

279834

This OEM kit comes with two ignition coils (one three-terminal boost/hold coil, and one two-terminal secondary coil). Usually only one of them burns out, but you should replace them as a set as both have to be operational for the gas valve to open. The primary purpose of the part is to open the gas valve and allow the gas to enter the burner. This is a safety mechanism to make sure that there is never an unsafe buildup of gas inside the appliance. You will find the coils attached to the dryer gas valve. This is not an uncommon repair; it can fail due to normal material fatigue over time. To test your current parts, watch the burner, and if the igniter glows for a while and then shuts off without the gas is igniting, it usually means one of these coils is bad.

Fix Number

FIX11746909

Manufacturer Part Number

WP9703438

Sometimes referred to as a retaining clip, the retaining ring is used to hold the drum support roller onto the shaft in your dryer. The clip may need to be replaced if you find that your dryer is noisy while tumbling or will not tumble at all. The retaining clip can also be used with stand mixers, to hold the pinion gear to the agitator shaft. This genuine OEM part is made entirely out of metal and measures approximately half an inch in diameter.

★★★★★

★★★★★

1 Review

Fix Number

FIX11743032

Manufacturer Part Number

WP6-3700340

If your dryer is making excessive noise, or it will not tumble, there may be an issue with the idler pulley wheel. The idler pulley wheel is attached to the idler bracket and is used to secure the dryer drum belt, which helps the drum to rotate. This genuine OEM part is made of white plastic with a metal center bearing. Over time this part can become worn, which will result in your drum not rotating or screeching noises when it spins. If this happens the idler pulley wheel should be replaced. Before beginning this repair, please be sure to disconnect the power supply to your dryer. To complete this job, you will need a Philips screwdriver, a 5/16 nut driver, a pair of Channellock pliers, and a small flat blade screwdriver.

Fix Number

FIX11741074

Manufacturer Part Number

WP33001807

This seal can be used for the front or rear drum. Adhesive is NOT included. For adhesive search: WPY055980