International Parts

Start With Your Model Number

Need help finding your model number?
Find Parts Fast
Guaranteed Fit
Repair Videos
Fix.com search
International Appliance Parts
Shop By Appliance Type

Popular International Parts

Watch the install video
Belt Kit – Part Number: 12112425
Belt Kit
$33.20
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX2005284
Manufacturer Part Number
12112425
Over time, the belts in your washer can either stretch out and sag, or become brittle and snap. When this happens, it can result in the belt losing its grip and will not be able to spin or drain the tub. If this happens, the belts will need to be replaced. This OEM belt kit includes the drive belt and the pump belt, which are both V-shaped, and made of black rubber. The pump belt is located between the motor and pump under the washer, and the drive belt is looped around the drive and motor pulley at the bottom of the machine. This repair is easiest to complete if the washer is placed on its back, and you will need to disconnect the power and water supply.
Fixes these symptoms

Installation Instructions

Ray from Olive Branch, MS
My washer was making a squeaky noise and vibrating on the rinse cycle.
I unplugged the washer then took the front cover off and took the screws holding the lid out. Then i leaned the washer back against the wall and unscrewed the nuts holding the 3 tub hold down springs. These look like 2 seperate nuts, 1 on top and 1 under the washer bottom but it is 1 long body nut so just put the socket on the bottom and back it all the way off. Then Take the drive and pump belts off and put blocking down under the tub pulley and pull the washer back down so the tub is resting on the Blocking, this will raise it up enough to clean the cone hub where the damper pads go. I used a mirror propped up inside the back of the washer to see the back side of the damper area to clean and install the new pads.The kit does not come with the glue needed to put the pads back on so don't forget to order it with the parts. Also the glue does not give a full cure time so i gave it 24 hours to be sure it was set. then i started putting everything back together. The tub springs gave me the most trouble. I was able to get 1 on easy but the other 2 i had to use a clamp on the support to the spring and use a pry bar to hold the spring down far enough to start the nut back on. But after that it all went easy and quick.This site does a great job with all the helpful instructions, pictures and videos. Read more...
M Series New Style Coil Kit – Part Number: 279834
M Series New Style Coil Kit
$28.91
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX334310
Manufacturer Part Number
279834
This OEM kit comes with two ignition coils (one three-terminal boost/hold coil, and one two-terminal secondary coil). Usually only one of them burns out, but you should replace them as a set as both have to be operational for the gas valve to open. The primary purpose of the part is to open the gas valve and allow the gas to enter the burner. This is a safety mechanism to make sure that there is never an unsafe buildup of gas inside the appliance. You will find the coils attached to the dryer gas valve. This is not an uncommon repair; it can fail due to normal material fatigue over time. To test your current parts, watch the burner, and if the igniter glows for a while and then shuts off without the gas is igniting, it usually means one of these coils is bad.
Fixes these symptoms

Installation Instructions

Dennis from ALISO VIEJO, CA
Dryer ran but did not dry clothing.
Best site I have ever used for repairs. First a list of what parts were needed was provided right from the start, no guessing. I followed all of the video's provided for installation instructions and and that was it. Very easy to make repairs and almost rebuilt my dated dryer to like new condition. Appliance was in very good physical condition just needed new components to bring it back. Highly recommend this site to anyone who can turn a wrench. Read more...
Watch the install video
Tumbler and Motor Belt – Part Number: WPY312959
Tumbler and Motor Belt
$27.28
In Stock
★★★★★
★★★★★
9 Reviews
Fix Number
FIX11757542
Manufacturer Part Number
WPY312959
This is a single OEM dryer drum belt. It measures 100 inches in length, 3/8 of an inch wide and has five ribs and four grooves. Keep in mind that this rubber drum belt will stretch over time, so if you are comparing your current belt to these specified measurements, they may not be exact. For this repair, you will need to disconnect the power, and remove the front panel and drum. You will need a 5/16 nut driver and a stubby Phillips screwdriver. While you are doing this repair, be careful not to let the belt fall into the groove in the drum, causing it to be too loose.
Fixes these symptoms
  • Drum Not Spinning
  • Marks left on clothes
  • Noisy
  • See more...

Installation Instructions

James from Gainesville, GA
"Sqealing" noise when drum rotating
Disconnected power supply, removed front panel, removed tub support bracket, removed electrical lines from light and door switch( to have better access to install front guide kit), removed belt, removed drum, removed old rollers, installed new rollers and rest of installation was in reverse order of taking machine apart. In order to install the front guide kit(which I've never done before), I had to watch the installation instructions via you-tube. This was a tremendous aide as the instructions were simple and very adequate. Read more...
Watch the install video
Front Glide Kit – Part Number: 306508
Front Glide Kit
$13.07
In Stock
★★★★★
★★★★★
3 Reviews
Fix Number
FIX1804752
Manufacturer Part Number
306508
This part is located on the front bulkhead of the dryer and helps the drum to rotate smoothly and quietly. If you notice a screeching or metal-on-metal noise while your appliance is operating, you may need to replace the front glides. This genuine OEM front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. We recommend replacing both sets of glides at the same time, which will require the purchase of two kits. To complete this repair, you will need a Philips screwdriver and a 5/16 nut-driver to remove the front panel and the bulkhead of the dryer, a drill with a 1/8-inch bit to remove the old rivets, and a rivet tool to install the new ones. Please ensure that you disconnect the power supply to your dryer before beginning this repair. While you have the appliance opened, we recommend vacuuming out any lint and debris, and inspecting the felt around the bulkhead and replacing if necessary.
Fixes these symptoms
  • Drum Not Spinning
  • Marks left on clothes
  • Noisy
  • See more...

Installation Instructions

James from Gainesville, GA
"Sqealing" noise when drum rotating
Disconnected power supply, removed front panel, removed tub support bracket, removed electrical lines from light and door switch( to have better access to install front guide kit), removed belt, removed drum, removed old rollers, installed new rollers and rest of installation was in reverse order of taking machine apart. In order to install the front guide kit(which I've never done before), I had to watch the installation instructions via you-tube. This was a tremendous aide as the instructions were simple and very adequate. Read more...
Watch the install video
Multi Rib Belt - 91-5/8 Inches – Part Number: WP33002535
Multi Rib Belt - 91-5/8 Inches
$27.83
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX11741110
Manufacturer Part Number
WP33002535
If your dryer is noisy while operating, or will not tumble at all, there may be an issue with the drum belt. Over time, the rubber can become brittle and snap, and the belt will need to be replaced. This genuine OEM multi rib dryer drum belt measures approximately 91 and 5/8-inch in length and is 3/8-inch wide. It is made of black rubber and have five ridges, helping it to grip to your dryer drum.
Fixes these symptoms

Installation Instructions

Tim from PORTLAND, OR
Dryer was a bit noisy with a full load of wet clothes
As per the repair videos on the site, I searched the internet for a couple of supplementary videos just to make sure I was doing it correctly. It was was all pretty easy. Expect to vacuum out and clean out the interior of the dryer. Also, to make things easier, disconnect the bulkhead and exterior like in the video, but also keep the top flipped up until reassembling, it'll make it much easier. When reinstalling the belt, remember how the belt is going to go around the pulley, you'll have to do this without sight as the barrel will the way and you won't be able to see what you're doing. It's really not hard but just keep this in mind. Also, as you disassembling, it would help to snap some pictures of where each screw goes and how; reassembly was a tiny bit tricky as I didn't do this. Read more...
Watch the install video
Light Bulb - 40W – Part Number: 8009
Light Bulb - 40W
$19.75
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX884734
Manufacturer Part Number
8009
This is a genuine OEM 40-Watt replacement light bulb that is compatible with various types of appliances. It has a frosted glass bulb with a standard metal socket base, making it easy to screw and unscrew by hand to replace. It is designed to tolerate extreme temperatures, which is why it is commonly used to light the inside of refrigerators and ovens. Depending on the appliance and location of the bulb, disconnecting the power is recommended. This bulb is sold individually.

Installation Instructions

Helen from Quincy, MA
lightbulb in refrigerator went out
Removed plastic shield on top of refrigerator. Removed old bulb.. Replaced new bulb. Reinstalled plastic shield. Voila! Read more...
Watch the install video
Drum Support Roller Kit – Part Number: 12001541
Drum Support Roller Kit
$22.91
In Stock
★★★★★
★★★★★
10 Reviews
Fix Number
FIX1570070
Manufacturer Part Number
12001541
This OEM drum support roller kit contains the parts needed to replace one roller on your dryer. This kit includes one drum roller and two bearings. Most dryers use two drum rollers, and it is recommended to change both at once for optimal performance. The drum support roller holds the drum in position while it spins on the support wheels. It rotates on the roller shaft located on the rear bulkhead. It may need to be replaced if your dryer is noisy, will not tumble, leaves marks on clothes, or will not start. This part is prone to wear and tear, and if broken will need to be replaced. This part measures roughly 3 inches in diameter and is made of plastic, metal, and rubber. Each kit is sold individually (two would be needed to replace both drum support rollers, which is recommended).
Fixes these symptoms
  • Drum Not Spinning
  • Marks left on clothes
  • Noisy
  • See more...

Installation Instructions

James from Gainesville, GA
"Sqealing" noise when drum rotating
Disconnected power supply, removed front panel, removed tub support bracket, removed electrical lines from light and door switch( to have better access to install front guide kit), removed belt, removed drum, removed old rollers, installed new rollers and rest of installation was in reverse order of taking machine apart. In order to install the front guide kit(which I've never done before), I had to watch the installation instructions via you-tube. This was a tremendous aide as the instructions were simple and very adequate. Read more...
Watch the install video
Blower Wheel with Clamp – Part Number: Y303836
Blower Wheel with Clamp
$21.82
In Stock
★★★★★
★★★★★
5 Reviews
Fix Number
FIX2200270
Manufacturer Part Number
Y303836
The blower wheel is responsible for blowing heat into the dryer drum, and out of the exhaust vent. If you notice that your dryer is taking too long to dry or is make unusually loud noises, it may be time to replace the blower wheel. This genuine OEM replacement part comes with a metallic clamp that holds the wheel in place. This part attaches to the drive motor shaft and can be accessed by removing the front panel of the dryer. Be sure to disconnect the power supply before beginning this repair.
Fixes these symptoms

Installation Instructions

Erik from Belvedere, CA
Noisy 'rattling' sounds from Dryer ->bad blower fan wheel
Watched the video - really helped me get prepared. Very simple repair: first, unplug power! Removed front panel 2 screws & slowly pulled panel outward to release top clips (2min). At unit bottom, removed the blower fan grey cover (7 screws, 3min). Pulled spring washer (careful not to bend) from shaft and removed spring clip on blower fan wheel (5 min). Installed new blower fan wheel onto shaft with washer&clip. Reinstalled blower cover/screws and front panel/screws. Total time about 15min. Thanks for an easy, inexpensive fix! Read more...
Watch the install video
Refrigerator Door Switch – Part Number: W11384469
Refrigerator Door Switch
$31.05
In Stock
★★★★★
★★★★★
3 Reviews
Fix Number
FIX12728638
Manufacturer Part Number
W11384469
Door switch turns the light off when you close the door.
Fixes these symptoms

Installation Instructions

Marilyn from Dublin, OH
Light switch no longer worked
Turn off and unplug your refrigerator. I used the screwdriver on the left side of the part (where the plug is) and used the putty knife at the same time on the right side to push the spring lock portion of the part in. The part snapped out. I unplugged the left contact from the plug and put it on the new part, then I unplugged the right contact and put it on the new part. I did this so the wires would not go up into the refrigerator and be hard to find. I put the left side of the new part where the plug and contacts are in first then I snapped the right side in place. I plugged the refrigerator back in and it worked perfectly. Just take your time and gently remove and reconnect the new part. The store where I bought my refrigerator wanted $69.95 for a service call plus an hourly charge and part charge. Count on this site for your parts and do it yourself. I ordered the part on Monday, it was delivered on Tuesday around noon and I made the repair that afternoon. Read more...
Watch the install video
Dryer Idler Pulley Wheel & Bearing – Part Number: WP6-3700340
Dryer Idler Pulley Wheel & Bearing
$19.63
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX11743032
Manufacturer Part Number
WP6-3700340
If your dryer is making excessive noise, or it will not tumble, there may be an issue with the idler pulley wheel. The idler pulley wheel is attached to the idler bracket and is used to secure the dryer drum belt, which helps the drum to rotate. This genuine OEM part is made of white plastic with a metal center bearing. Over time this part can become worn, which will result in your drum not rotating or screeching noises when it spins. If this happens the idler pulley wheel should be replaced. Before beginning this repair, please be sure to disconnect the power supply to your dryer. To complete this job, you will need a Philips screwdriver, a 5/16 nut driver, a pair of Channellock pliers, and a small flat blade screwdriver.
Fixes these symptoms

Installation Instructions

Tim from PORTLAND, OR
Dryer was a bit noisy with a full load of wet clothes
As per the repair videos on the site, I searched the internet for a couple of supplementary videos just to make sure I was doing it correctly. It was was all pretty easy. Expect to vacuum out and clean out the interior of the dryer. Also, to make things easier, disconnect the bulkhead and exterior like in the video, but also keep the top flipped up until reassembling, it'll make it much easier. When reinstalling the belt, remember how the belt is going to go around the pulley, you'll have to do this without sight as the barrel will the way and you won't be able to see what you're doing. It's really not hard but just keep this in mind. Also, as you disassembling, it would help to snap some pictures of where each screw goes and how; reassembly was a tiny bit tricky as I didn't do this. Read more...

International Appliance Types

Popular International Models

View More
+