OEM Maytag Dryer Roller Shaft [WP6-3129480] | Ships Today | Fix.com
Roller Shaft – Part Number: WP6-3129480
Roller Shaft – Part Number: WP6-3129480 https://fixcom.azureedge.net/Schematics/Maytag/59071.gif

Roller Shaft

Your Price
$5.85

Fix Number: FIX11743031

Manufacturer #: WP6-3129480

Manufactured by: Whirlpool

Get this part fast. Average delivery time via standard shipping: 1.8 days.

Part description

This roller shaft is the axle for the drum roller, also known as drum roller axle.

Works with the following brands

Maytag, International, Jenn-Air, Crosley, Roper

Works with the following products

Dryer, Washer Dryer Combo

Fixes the following symptoms

Noisy | Will not tumble

Videos For installing this part.

Installation Instructions Provided by Fix customers like you.

Average Repair Rating: 2.8 / 5.0, 22 reviews
>
<
Customer:
Tim from PORTLAND, OR
Parts Used:
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers
Dryer was a bit noisy with a full load of wet clothes
As per the repair videos on the site, I searched the internet for a couple of supplementary videos just to make sure I was doing it correctly. It was was all pretty easy. Expect to vacuum out and clean out the interior of the dryer. Also, to make things easier, disconnect the bulkhead and exterior like in the video, but also keep the top flipped up until reassembling, it'll make it much easier. When reinstalling the belt, remember how the belt is going to go around the pulley, you'll have to do this without sight as the barrel will the way and you won't be able to see what you're doing. It's really not hard but just keep this in mind. Also, as you disassembling, it would help to snap some pictures of where each screw goes and how; reassembly was a tiny bit tricky as I didn't do this.
5 of 5 people found these instructions helpful

Were these instructions helpful?   

Customer:
James from SANTA ROSA, CA
Parts Used:
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
My drier was making rumbling noises.
I followed the video instructions, which were great by the way. Pretty easy to remove the front panel, then housing, then belt, then drum to expose drum support rollers and shafts. Removed old and replaced with new after cleaning lint up a bit. Unfortunately, there is still a bit of a rumble when the drier starts up. I fully expected the changed out parts to make a difference, but it was only a modest improvement. I need to do further trouble shooting and diagnosis.
2 of 2 people found these instructions helpful

Were these instructions helpful?   

Customer:
Steven from Troy, OH
Parts Used:
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
Dryer was making noise like an indy car now like a prius
Exactly like in the online video. The video was an excellent tool for this repair. Thank you, !
1 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Brian from Novi, MI
Parts Used:
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set
Squeaking noises while running dryer
Followed the Video Directions from website. All went as planed. The dryer is running like new now.
1 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Tammy from Fremont, OH
Parts Used:
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
Very loud rubbing/squeaking noise
Watched 2 YouTube videos. 1. How to take apart a dependable care dryer. 2. How to replace a belt on a maytag dryer. We replaced all the parts. It was eeasy. When putting dryer back together make sure felt is straight. We did have to take it apart again there was felt sticking out inside the dryer and it caused the drum to not spin. Everything works great. And Thank you parts select. I received the right parts in 2 days without paying extra. I will use you again.
1 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
donald from franklin lakes, NJ
Parts Used:
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Socket set
Replace drum rollers and their shafts
followed applianceparts video on youtube,although dryer somewhat different(older) ....video made the repair happen...
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Eric from Fort Bragg, CA
Parts Used:
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Wrench set
Dryer had squeaking noise
Remove door and front panel remove drum replace drum support roller and roller shaft.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Randall from Valrico, FL
Parts Used:
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Screw drivers, Wrench set
Noisy
I pulled the entire unit apart, because I didn't , for sure, know what the problem was. I'm glad I did as it had years of crud and dust in it. The shaft and roller were easy to install. The belt routing was the hardest part, which was actually simple. It now makes no noise and dries really good.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
John from McAllister, MT
Parts Used:
Difficulty Level:
Easy
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers, Socket set, Wrench set
Dryer was extremely noisy squeeling and sqeaking
Followed installation videos and removed entire front of cabinet including door, loosened belt and removed drum. Only problem was the snap ring pliers I had were too large to fit in the holes of the drum roller snap ring. Ended up taking two 3 inch deck screws with sharp points, putting them in the snap ring holes and removing the ring by that method. Did the same when replacing it although this time, had to have my wife put a flat screwdriver against it while I pulled it apart with the screws. Rest of the repair was quite easy and dryer works great.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Robert from Encinitas, CA
Parts Used:
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set, Wrench set
Periodic screeching sound
1. bought the only snap ring pliers available at homedepot. 2. turned off the gas and unplugged 3. moved it away from back wall. 4. removed front panel. 5. removed drum housing. 6. slid off belt. 7. removed drum. 8 found one frozen roller and a second with roller washer severely worn washer. The pins on the snap ring plier were too large to insert into the spring rings. ground the small pins down with a power grinder until finally fit. (took a long time). Finally fit well enough to get retaining rings off. 9. replaced both shafts and rollers, though it was unclear whether the solid shafts needed replacement. 10. from rear, removed access panel and replaced idler pulley wheel. 11. placed drum back with new belt, then fit it over motor and pulley. Took a bit to get it fitted correctly. Much easier from rear panel than reaching around. 12. reinstalled housing and front panel. Problem areas: GET A SMALL SNAP RING PLIERS THAT WILL FIT ! Easier to install belt around idler pulley wheel from rear access panel. Replacement of roller shafts was probably not necessary. Works great now.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Alton from Greenbrier, TN
Parts Used:
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Drum vibration
I removed the drum per instructions provided on the web site. Removed the two roller shafts. Installed the two new roller shafts and applied grease to the shaft. I secured the two rollers using the existing snap rings. I reassembled the dryer in the reverse order of dis assembly. Machine runs like it did when it was new. Easy job.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Scott from Burton, OH
Parts Used:
Difficulty Level:
Very Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Wrench set
Dryer very noisy and squeaking
Perform exactly as was showed in the video on the page when ordering the part. It is the same except for disassembling the front of the cabinet. The cabinet in the video was different than the dryer I have. Once the cabinet was apart, the inside was the same. The other difference was my belt, the ribs run are inside, not outside, like in the video.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Boyd from kalamazoo, MI
Parts Used:
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Dryer(stack unit piece) began making a grating, squeaking sound when starting. Got worse as time when on.
I followed other's direction to remove front panel, switch assembly and front frame supporting the drum. Removing the belt sounded daunting, so after inspecting the whole setup, I removed the front flanges and cover for the blower fan and removed the fan, even though it did not need to be replaced. That left the motor shaft, idler pulley & spring readily visible and much easier for me to understand how to remove the belt. I found a wooden yard stick held the front of the drum up in place momentarily so replacing the belt was even easier. I skinned up a couple knuckles but after replacing the rollers and front slide pads(easy!) it works great and dries better too.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Terrence from St Louis, MO
Parts Used:
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Wrench set
Easy to repair but difficult to reassemble
Although it was easy to take apart my dryer and replace the worn out parts, it was difficult to reassemble everything correctly. It took me about 15 minutes to get the belt correctly on the rollers. In addition, I ended up with a couple of extra screws after I had reassembled the dryer. :) I suggest taking pictures or even a video as you take apart the dryer unit so you can see the correct sequence as you reassemble your dryer.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Michael from Camino, CA
Parts Used:
Difficulty Level:
Easy
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Wrench set
I had a horrendous squealing noise that sounded like bearings that needed oil.
First I watched the video on how to take the front off and gain access. Simple and straight fore ward. Then watched the video on how to remove the drum. Simple. Located the Drum Rollers. I spun the right one---it was grinding and definitely bad. I spun the left one---it was not as bad but still did not spin freely and quietly. Watched the video on how to install new Roller Shafts and Drum Wheels. I needed a 1/2" box wrench to remove the hex nut holding the Roller Shaft (not a 5/8" as in the video). A simple job. I then watched the video on how to install a new Blower Wheel. My Blower Wheel wobbled a little. It fit a little loose on the shaft and vibrated when spinning. So I replaced it as long as I had the dryer open anyway. Likewise for the Idler Pulley Wheel. I don't know if it was also making noise but I replaced it anyway. Again a simple job. I took time to clean and vacuum up all the lint and dust from the entire insides as needed. Good for another 10 years now! The videos make this an "easy" repair project. This was my first repair on any Dryer. I spent more time cleaning up the dust etc. inside than I did installing the new parts. It runs great now! Quiet! Since it is over ten years old I would imagine the next thing to fail will be something electrical but now I know I can learn how to repair what ever is needed from the appropriate video and then order the parts.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

>
<

Model Cross Reference

This part works with the following models:

Fix Number: FIX11743031
Manufacturer Part Number: WP6-3129480
Brand
Model Number
Description
Roper
2570B00
Range - Electric
Roper
2570B10
Range - Electric
Crosley
CDE4205AYJ
Dryer - Residential
Crosley
CDE4205AYW
Dryer - Residential
Crosley
CDE4205AZJ
Dryer - Residential
Crosley
CDE4205AZW
Dryer - Residential
Crosley
CDG4205AWJ
Dryer - Residential
Crosley
CDG4205AWW
Dryer - Residential
Maytag
DE106
Dryer - Electric
Maytag
DE107
Dryer - Electric
Maytag
DE110
Dryer - Electric
Maytag
DE18CA
Dryer - Electric
Maytag
DE18CM
Dryer - Electric
Maytag
DE18CS
Dryer - Electric
Maytag
DE18CT
Dryer - Electric
Maytag
DE19CA
Dryer - Electric
Maytag
DE19CD
Dryer - Electric
Maytag
DE19CS
Dryer - Electric
Maytag
DE19CT
Dryer - Electric
Maytag
DE210
Dryer - Electric
Maytag
DE212
Dryer - Residential
Maytag
DE21CA
Dryer - Electric
Maytag
DE21CM
Dryer - Electric
Maytag
DE21CS
Dryer - Electric
Maytag
DE21CT
Dryer - Electric
Maytag
DE22CA
Dryer - Electric
Maytag
DE22CS
Dryer - Electric
Maytag
DE22CT
Dryer - Electric
Maytag
DE23CD
Dryer - Electric
Maytag
DE24CA
Dryer - Electric