Models > DBVH512EF0WW

DBVH512EF0WW General Electric Dryer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for DBVH512EF0WW

Viewing 7 of 7

Manuals & Guides for DBVH512EF0WW

Click to download
Keep searches simple, eg. "belt" or "pump".
This single drum bearing slide attaches to the outer-most side of the bearing. This part is also sometimes referred to as a drum slide, drum glide, or drum pad. It provides support to the front of the...
In Stock
Order within the next 9 hrs and your part ships today!
This single drum bearing slide is an OEM approved replacement part for dryers. It can also be known as a bearing drum slide, pad, or glide. The slides attach to the inner most slots on the front beari...
Special Order
This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromis...
In Stock
Order within the next 9 hrs and your part ships today!
This 89.5-inch drive belt is for dryers. It has a 4-rib design on the inside for a better grip. If comparing the size of your current belt to the new one, keep in mind that a small amount of stretchin...
In Stock
Order within the next 9 hrs and your part ships today!
If the lightbulb inside your dryer drum has burned out, this is an authentic OEM replacement. It is a 10W, 120V bulb that is sold individually. The bulb turns on when the dryer door is open and should...
In Stock
Order within the next 9 hrs and your part ships today!
This rear drum bearing kit is a genuine OEM replacement for your dryer. The kit includes a shaft, ground strap, bracket, bearing and seven screws for installation. The bearing supports that back of th...
In Stock
Order within the next 9 hrs and your part ships today!
$60.89
The drum slides are not included with this part. The top bearing helps your dryer operate as quietly as possible. This part will require two green drum slides and 2 white drum slides.
In Stock
Order within the next 9 hrs and your part ships today!
A dryer's idler pulley wheel serves to help the belt to rotate the drum.
In Stock
Order within the next 9 hrs and your part ships today!
$11.37
This part helps to keep the door closed while the machine is running.
In Stock
Order within the next 9 hrs and your part ships today!
This interlock switch is a genuine OEM part that can be used in a variety of appliances like dishwashers and dryers. The switch is also known as a belt switch and works as a simple on and off mechanis...
In Stock
Order within the next 9 hrs and your part ships today!
Sold individually.
In Stock
Order within the next 9 hrs and your part ships today!
TThe door strike for your dryer is mounted on the dryer frame that the door shuts onto. It fits into the door catch on the door and keeps the door closed. If the door strike is damaged or missing, the...
In Stock
Order within the next 9 hrs and your part ships today!

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for DBVH512EF0WW

Viewing 10 of 10
Noisy
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Marks left on clothes
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Door won’t close
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing
How to fix it
Drum Not Spinning
Fixed by these parts
Fixing
How to fix it
Won’t Start
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Too hot
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Not Heating
Fixed by these parts
Fixing
How to fix it
Door latch failure
Fixed by these parts
Fixing
How to fix it
Heat stays on after drum has stopped
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Matthew from Plainfield, IL
Parts Used:
WE09X27634, WE1M1067, WE1M504
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Due to over loading of the dryer the drum ruined the slides and was making a bad noise due to plastic rubbing plastic
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and drum. I put the new slides in place and installed a new felt strip. I put it back together and that was that. Very easy.
793 of 904 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bruce from Springfield, MA
Parts Used:
WE09X27634, WE14M124, WE1M1067, WE1M504
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
LOUD - screeching noise during drying cycle, in all modes of operation.
1. Removed top cap on lid by removing the 3 - phillips screws.
2. removed front digital display panel from PC board.
3. removed bolts with nut-driver on the top of the front panel, removed bottom screws with #2 square bit.
4. removed "snap-in" plastic top bearing ( paying attention to where wiring is routed within this fram e.
5. cleaned all areas of plastic and felt debris, installed new bearing, felt, and glides.
6. Re-installed all wiring and panels.

*** make sure to order all of the glides, there should be a total of 4 for the top assembly.
248 of 337 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Brian from Clinton, MO
Parts Used:
WE11M23
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Heater element went out
First of all, unplug the dryer. I removed the two screws on the front of the cabinet to remove the top. I then took out the screws to remove the dial panel. Release the belt for the drum through the access hole in the rear of the dryer. Remove the front cover and pull the drum assembly out.

Remove the element disc from the rear of the housing, take note of the the wireing placement. Replace disc and reverse order of disassembly.

This job was easy for me as I am a tinkerer by nature. The hardest part of the whole job was waiting on the part, which by the way was ordered on a Sunday evening and I had the replacement in my hands and back in the dryer running by 1:00 PM on the following Tuesday!

I book marked this website and WILL refer it to others who simply need a repair, not a costly new appliance!
185 of 220 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!