Hotpoint Dryer Parts
Start With Your Model Number
Find Parts Fast
Guaranteed Fit
Repair Videos
Need help finding your model number?

Popular Hotpoint Dryer Parts
$31.29
In Stock
BELT DRIVE
Fix Number FIX16542496
Manufacturer Part Number WE03X29897
This 89.5-inch drive belt is for dryers. It has a 4-rib design on the inside for a better grip. If comparing the size of your current belt to the new one, keep in mind that a small amount of stretching and contortion will occur over time, and this belt will fit despite small inaccuracies. You will find this part wrapped all the way around the dryer drum, around a tension pulley, and around the drive motor pulley. This allows the parts to work together to spin the drum as the motor rotates. A common symptom of a broken drive belt is a drum that will not turn. This part is prone to wear and tear over time and will likely stretch or become brittle, leading to complete breakage of the part. The drum cannot spin without a drive belt, so it needs to be replaced immediately. For this repair, we recommend wearing work gloves to protect your hands from sharp edges, disconnect the power, remove the main panel, and access the motor drive to secure the new belt in place.
Fixes these symptoms
- Drum Not Spinning
- Noisy
- See more...
Installation Instructions
Nae from BRENTWOOD, TN
The dry was making a whining sound. Very loud.
I followed all the video on the website with all the parts I had purchased. Very easy. Just make sure you unplug the dryer first. Thank you,
Read more...
$18.58
In Stock
Drum Bearing Slide - White
Fix Number FIX755842
Manufacturer Part Number WE1M504
This single drum bearing slide attaches to the outer-most side of the bearing. This part is also sometimes referred to as a drum slide, drum glide, or drum pad. It provides support to the front of the drum as it rotates. They are approximately 3-inches long, 1 inch wide and made from a durable white plastic. If your appliance starts making unusual sounds, is not drying clothes properly, or leaves marks on clothes, it may be time to replace this part. The dryer has 2 slides, which we recommend replacing at the same time, as they tend to wear out at the same rate. You will need to order 2 of this part to replace both drum bearing slides, since it is sold individually. Before you begin this repair, be sure to disconnect the power to the dryer.
Fixes these symptoms
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
Donald L. from Belmont, MA
Dark marks on clothing; clothing sticking between drum and front panel
Others with the same problem of dark marks on clothing suggested replacing the white and the grey drum slides that slip into the front drum bearing unit. When I open up the dryer, I did find that both the white and grey drum slides on one side of the front drum bearing piece had completely worn away, and some of the drum bearing piece was also worn away. I had decided in advance to order both white slides, both grey slides, a new felt seal, and the front drum bearing piece. Possibly I could have reused the old front drum bearing, but the replacement was cheap enough. Three bits of advice: 1) if you replace the felt seal, make sure you get it tucked behind the clips on the door panel; 2) if you replace the front drum bearing piece, once you have the dryer put back together, reach up and pull the plastic drum bearing toward you to be sure it is fully snapped into place; 3) after you replace the slides or felt, the drum will make mild rubbing noises as it turns, so run the dryer with no heat for about 30 minutes to seat the parts.
Read more...
$14.29
In Stock
Drum Bearing Slide - Green
Fix Number FIX6447706
Manufacturer Part Number WE1M1067
This single drum bearing slide is an OEM approved replacement part for dryers. It can also be known as a bearing drum slide, pad, or glide. The slides attach to the inner most slots on the front bearing. As the dryer rotates, the drum bearing slides help to support the front of the drum. If your appliance becomes noisy, is not drying properly, or leaves marks on clothes, it may be time to replace it. If you are replacing one slide, we recommend replacing the other slide at the same time, as they deteriorate at a similar rate. You will need to order 2 of these parts as there are 2 in each dryer. It is approximately 2.6-inches deep, 0.06-inches in height, and 0.5-inches wide. This part is denoted as being green in the title, however users and technicians have noted it is actually gray in color.
Fixes these symptoms
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
Donald L. from Belmont, MA
Dark marks on clothing; clothing sticking between drum and front panel
Others with the same problem of dark marks on clothing suggested replacing the white and the grey drum slides that slip into the front drum bearing unit. When I open up the dryer, I did find that both the white and grey drum slides on one side of the front drum bearing piece had completely worn away, and some of the drum bearing piece was also worn away. I had decided in advance to order both white slides, both grey slides, a new felt seal, and the front drum bearing piece. Possibly I could have reused the old front drum bearing, but the replacement was cheap enough. Three bits of advice: 1) if you replace the felt seal, make sure you get it tucked behind the clips on the door panel; 2) if you replace the front drum bearing piece, once you have the dryer put back together, reach up and pull the plastic drum bearing toward you to be sure it is fully snapped into place; 3) after you replace the slides or felt, the drum will make mild rubbing noises as it turns, so run the dryer with no heat for about 30 minutes to seat the parts.
Read more...
$65.01
In Stock
Rear Drum Bearing Kit
Fix Number FIX267529
Manufacturer Part Number WE25M40
This rear drum bearing kit is a genuine OEM replacement for your dryer. The kit includes a shaft, ground strap, bracket, bearing and seven screws for installation. The bearing supports that back of the dryer drum and helps to reduce friction so that the drum can rotate smoothly and quietly. If the bearing has worn out, it can result in your dryer not tumbling, or making excessive noise when it is running.
Fixes these symptoms
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
Stephen from Bridgewater, NJ
noisy
New shaft, belt and housing. Installation was going fine until went to install belt and IT was way to short .THANKS
Read more...
$63.26
In Stock
Front Drum Bearing
Fix Number FIX960316
Manufacturer Part Number WE3M26
Located on the inside of the dryer front panel, the front drum bearing helps your appliance to operate as quietly as possible. It allows the front of the drum to glide smoothly on the felt seal of the front panel when the drum is rotating. This manufacturer-approved part is made of a durable white plastic and measures approximately 9 inches by 20 inches. If your dryer makes a continuous banging noise while it is powered on, it is likely that the drum bearings need to be replaced. Keep in mind that the drum slides should be replaced at the same and will need to be purchased separately (the front drum bearing holds 4 glides), as this part includes the bearing only.
Fixes these symptoms
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
Donald L. from Belmont, MA
Dark marks on clothing; clothing sticking between drum and front panel
Others with the same problem of dark marks on clothing suggested replacing the white and the grey drum slides that slip into the front drum bearing unit. When I open up the dryer, I did find that both the white and grey drum slides on one side of the front drum bearing piece had completely worn away, and some of the drum bearing piece was also worn away. I had decided in advance to order both white slides, both grey slides, a new felt seal, and the front drum bearing piece. Possibly I could have reused the old front drum bearing, but the replacement was cheap enough. Three bits of advice: 1) if you replace the felt seal, make sure you get it tucked behind the clips on the door panel; 2) if you replace the front drum bearing piece, once you have the dryer put back together, reach up and pull the plastic drum bearing toward you to be sure it is fully snapped into place; 3) after you replace the slides or felt, the drum will make mild rubbing noises as it turns, so run the dryer with no heat for about 30 minutes to seat the parts.
Read more...
$11.56
In Stock
FELT TRAP DUCT
Fix Number FIX12722961
Manufacturer Part Number WE09X27634
This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromised. Disconnect power to the dryer before completing this repair. You will need to remove the front of the dryer to gain access to the felt seal. This felt seal may differ in appearance from your original but will function the same as your original. This is an OEM replacement part that is sourced directly from the authentic manufacturer.
Fixes these symptoms
- Marks left on clothes
- Noisy
- Too hot
- See more...
Installation Instructions
Donald L. from Belmont, MA
Dark marks on clothing; clothing sticking between drum and front panel
Others with the same problem of dark marks on clothing suggested replacing the white and the grey drum slides that slip into the front drum bearing unit. When I open up the dryer, I did find that both the white and grey drum slides on one side of the front drum bearing piece had completely worn away, and some of the drum bearing piece was also worn away. I had decided in advance to order both white slides, both grey slides, a new felt seal, and the front drum bearing piece. Possibly I could have reused the old front drum bearing, but the replacement was cheap enough. Three bits of advice: 1) if you replace the felt seal, make sure you get it tucked behind the clips on the door panel; 2) if you replace the front drum bearing piece, once you have the dryer put back together, reach up and pull the plastic drum bearing toward you to be sure it is fully snapped into place; 3) after you replace the slides or felt, the drum will make mild rubbing noises as it turns, so run the dryer with no heat for about 30 minutes to seat the parts.
Read more...
$9.01
In Stock
D-Shaped Knob Clip
Fix Number FIX268493
Manufacturer Part Number WH01X10106
This clip fits inside the control knobs for your laundry machines, and helps to securely fasten the knob to the shaft, which allows you to easily turn the knob to select the correct settings. This is a genuine OEM part that is made of metal, designed to fit onto a D-shaped shaft, and is sold individually. If the control knob has become loose, or it is difficult to select settings, the clip may need to be replaced. Needle nose pliers may be required to either remove the clip from the shaft, or to pull it out of the knob. The new clip can simply be inserted into the control knob.
Fixes these symptoms
- Will Not Start
- See more...
Installation Instructions
KERY from PAOLA, KS
Dryer knob was cracked and would not turn the timer.
Super easy...just pulled off the cracked knob and replaced with the new knob.
Read more...
Timer Knob
Step 2. Removed the start switch by gently twisting left and pulling out of the socket.
Step 3. Removed the three wires, one at a time and placed them on the new start switch, then installed the new switch in its socket by gently twisting to the right.
(Note: plugged power cord back in and tried the new Start Switch. Still would not start.)
Step 4. Removed the Timer Knob by pulling strait off the shaft, then replaced with the new knob. Pushed the Start button and the Dryer worked. The old knob was obviously stripped so as to slip on the Timer shaft, giving the impression it was moving but it was not. Read more...
Fix Number FIX1482196
Manufacturer Part Number WE1M652
If your current timer knob has become cracked or otherwise damaged, this is the replacement part you will need. This knob is meant for D-shaped shafts only. The timer knob allows you to select the amount of time your dryer will run for, so if broken can make setting the time and starting your dryer difficult. It is approximately 3 inches in diameter and is made of durable white plastic. No tools are required for this repair, just pull the existing knob straight off the shaft and install the replacement. Knobs are sold individually and are sourced from the manufacturer.
Fixes these symptoms
- Timer Not Working
- See more...
Installation Instructions
William from MARYVILLE, TN
My dryer would not start
Step 1. After unplugging the dryer from the wall outlet, Removed 6 screws holding the back cover of the instrument panel.Step 2. Removed the start switch by gently twisting left and pulling out of the socket.
Step 3. Removed the three wires, one at a time and placed them on the new start switch, then installed the new switch in its socket by gently twisting to the right.
(Note: plugged power cord back in and tried the new Start Switch. Still would not start.)
Step 4. Removed the Timer Knob by pulling strait off the shaft, then replaced with the new knob. Pushed the Start button and the Dryer worked. The old knob was obviously stripped so as to slip on the Timer shaft, giving the impression it was moving but it was not. Read more...
$15.61
In Stock
Door Latch
Fix Number FIX3502777
Manufacturer Part Number WE1M1011
This part helps to keep the door closed while the machine is running.
Fixes these symptoms
- Door won’t close
- See more...
Installation Instructions
Helen from South Plainfield, NJ
Door would not close
So easy ! I am a female senior citizen and this repair took only a screw driver to pry off the old latch and needle nose pliers to pull it out. The parts were under $10 and it saved me hundreds since I didn't have to call a repairman or purchase a new dryer.
Read more...
Drive Belt
Fix Number FIX2350043
Manufacturer Part Number WE12X10014
This belt has a length of 87 inches, width of 1/4”, flat, with 4 ridges.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
John from West Elkton, OH
Replacing belt
First watched some you tube videos, to see how to get dryer apart, the one issue I had was getting the belt onto pulley etc. I found if I removed small access panel in back it was a lot easier than trying to reach in from the front as shown in most of the online videos
Read more...
Appliance Type
Related Pages
- Hotpoint Dryer Circuit Boards and Touch Pads
- Hotpoint Dryer Drums and Tubs
- Hotpoint Dryer Hardware
- Hotpoint Dryer Knobs
- Hotpoint Dryer Switches
- Hotpoint Dryer Thermostats
- Hotpoint Dryer Timers
- Hotpoint Dryer Valves
Popular Hotpoint Dryer Models
- HTDX100EM8WW ELECTRIC DRYER
- HTDP120ED0WW
- HTDX100ED6WW ELECTRIC DRYER
- HTDX100ED0WW
- NVLR333EV0WW Residential Electric
- HTDX100EM2WW
- NVLR333ET0WB Residential
- HTDX100EM7WW ELECTRIC DRYER
- HTX24EASK0WS ELECTRIC DRYER
- HTX21EASK0WW ELECTRIC DRYER
- HTDX100EM1WW
- HTDX100EM0WW Residential Electric
- HTDX100GM8WW GAS DRYER
- HTDX100EM6WW ELECTRIC DRYER
- HTDX100ED4WW ELECTRIC DRYER
- HTDX100EM4WW
- DLB3400SBLWH Residential
- NBXR453EV0WW Residential Electric
- HTDX100ED5WW ELECTRIC DRYER
- HTDX100ED3WW ELECTRIC DRYER