Hotpoint Parts

Hotpoint Appliance Parts
Shop By Appliance Type

Popular Hotpoint Parts

$9.42
  In Stock
Light Bulb - 40W
Fix Number FIX217532
Manufacturer Part Number 40A15
This 40-Watt lightbulb is sold individually and is a genuine OEM replacement option for your home appliances. It is specially designed to withstand extreme temperatures, so this bulb is compatible with a variety of appliance types including refrigerators, ranges, microwaves, and dryers. It features a frosted glass bulb with a standard metal socket base, which allows you to easily unscrew the burnt-out light and twist the new bulb into place. Depending on your appliance, there may be a guard or cover protecting the lightbulb, in which case you may require additional tools to remove the cover. We recommend disconnecting the power supply to your appliance before changing the lightbulb.
Installation Instructions
Jeffrey from SEATTLE, WA
Bake element replacement
1. Turn of over power at the breaker.
2. Remove bake element cover. There's 2 quarter inch nuts.
3. Disconnect old element. For me there was not much play in the wires so when I disconnected the old element I lost the wire in the insulation. If this happened you can remove the central plate cover on the back of the oven and you can easily find the wires again.
4. Connect the replacement element.
5. Screw the bake element cover back in.
6. Turn power back on.
Read more...
$262.05
  In Stock
Ice Maker
★★★★★
★★★★★
(4)
Fix Number FIX1993870
Manufacturer Part Number WR30X10093
The ice maker assembly makes ice by filling the tray with water from the inlet valve, freezing it until solid cubes are formed, and then ejecting them into the ice bucket. This process will repeat until the bucket has reached capacity. If your fridge is no longer making ice, the assembly may need to be replaced. This is a genuine OEM replacement that measures 10 inches by 5 inches in size and will make seven crescent shaped pieces of ice each cycle. The kit is mainly made of white plastic, and includes a 4-pin round plug-in connector, a 6-post plug-in connector, tube, and fill cup. Depending on your frequency of use, the ice maker may need to be replaced every three to ten years. Regular wear and tear is the main reason this part may need to be replaced but be mindful of accidental damage.
Fixes these symptoms
  • Ice maker dispenses too little ice
  • Ice maker dispenses too much ice
  • Ice maker not making ice
  • See more...
Installation Instructions
marion from raleigh, NC
Ice maker stopped making ice
Super easy. Loosen 2 screws. Disconnect power line. Take out broken part and plug in new part then slide icemaker back in place and tighten 2 screws. Saved me the $89 service call plus whatever they would have overcharged for the part! And no waiting around for repair guy! Read more...
$14.17
  In Stock
Light Switch
Fix Number FIX8758429
Manufacturer Part Number WR23X10725
The light switch in your refrigerator is used to turn the light on and off when the fridge door opens or closes. This is considered a closed switch, which means that when the fridge door depresses the button there is no continuity and the light turns off. When the fridge door opens and the button is released, there is continuity, and the light turns on. If the light in your fridge is not burned out but will not come on, the switch may need to be replaced. This genuine OEM replacement light switch is spring loaded and made of a white plastic. This is an easy repair that will require a flat blade screwdriver and a pair of needle nose pliers to complete the job. Since you will be working with electrical components, please be sure to disconnect the power supply to your fridge before beginning this repair.
Fixes these symptoms
Installation Instructions
Sheila from los angeles, CA
Door would not close after insatallation
Followed the video with no problems, but the door would not close. There is a rubber bumper that the light switch strikes, This bumper was not horizontal, and just had to be twisted to a horizontal position. The door then closed tightly, Total repair time was about 5 minutes! Read more...
$55.71
  In Stock
Bake Element - 220V 2300W
★★★★★
★★★★★
(2)
Fix Number FIX249466
Manufacturer Part Number WB44X5082
The bake element provides heat to your range in order to cook your food. If your oven is not heating or has inconsistent temperatures, it may be time to replace the element. This is a genuine OEM replacement part for your range that measures approximately 15-1/4 inches long and 18-1/4 inches wide. It is a closed hinged style of element and is 220 volts and 2300 watts. Be sure to disconnect the power supply to your range before beginning this repair.
Fixes these symptoms
  • Element will not heat
  • Little to no heat when baking
  • Little to no heat when broiling
  • See more...
Installation Instructions
Stephen from Davie, FL
Element not fully heating
Removed 4 screws and old element. Installed new one. Simple. Remember to flip the circuit breaker first. Read more...
$131.17
  In Stock
Crisper Drawer Cover
★★★★★
★★★★★
(1)
Fix Number FIX890565
Manufacturer Part Number WR32X10398
The crisper drawer cover contains the rails that your crisper drawers slide in and out on, as well as acting as a shelf to store other items in your fridge. If your drawers are difficult to open and close, or the cover has any visible signs of damage, it should be replaced so that your crispers continue to function as intended. This is an easy repair that does not require any tools. Simply remove the crisper drawers, then lift out the cover. Place the new cover in the fridge, and reinstall the crisper drawers. Carefully check to ensure that your fridge door will close properly, and you are all set. Please note that this part may look different than the original one you are replacing, but it is a genuine OEM part that will work with your refrigerator. The crisper drawer cover is made of plastic and is white in color.
Fixes these symptoms
Installation Instructions
ebubedike from houston, TX
broken cover split in three pieces
I had to open the fridge door wide open. Remove the old broken ones. Gently align and slide the new one in.Then gently make sure that it sits well on the protruded wall end support. Read more...
$23.98
  In Stock
Temperature Sensor
★★★★★
★★★★★
(1)
Fix Number FIX304103
Manufacturer Part Number WR55X10025
The temperature sensor, also referred to as a thermistor, is used to monitor the refrigerator and freezer internal temperatures. The sensor is a small capsule like device that is protected by a white plastic casing. The sensor sends the temperature reading to the control board, which uses this information to turn on the compressor and fan circuits. If this part is malfunctioning it may inaccurately signal the control board to turn off these components, resulting in warmer than normal temperatures in the fresh food and freezer sections. This part can break from material fatigue through normal use, and will need to be replaced when this happens. You will find this part attached to the evaporator and control housing in your appliance. This OEM part measures roughly 1.25 inches with 18-inch long wire leads. For this repair, you will need a 1/4 inch nut driver, a pair of strippers and crimpers, and a pair of wire splice connectors.
Fixes these symptoms
  • Doesn’t stop running
  • Freezer not defrosting
  • Freezer section too warm
  • See more...
Installation Instructions
Steven from Indio, CA
Fresh food section not cooling
Online info suggested thermal sensor was the issue (coils cleaned, fans functional). I ordered the part and received it in 2 days. Finding the sensor was the issue. I removed the shelves, then removed a temp control knob, the lights and the protective panel covering them. I removed a long white panel (no screws), removed two panels (one with 2 screws, one with three screws. The thermal sensor was behind the last panel removed. The cooling coils with the thermal sensor were covered with a styrofoam like device. Used a hair dryer to melt the ice. The new sensor was then put in place as per other videos on this topic. It took longer to melt the ice then to remove the panels giving access to the sensor. All in all a pretty easy repair. BTW, refrigerator is working fine (0-2F in freezer, 37F in fresh foods side). Read more...
$71.92
  In Stock
EVAPORATOR FAN MOTOR
Fix Number FIX12741350
Manufacturer Part Number WR60X31522
This is an evaporator fan motor, located in the freezer compartment. It is sold as a single unit. It is responsible for moving air over the evaporator coils as the compressor is running. When this part is faulty you may hear loud sounds coming from the freezer area, your refrigerator may not stay as cold as normal, or the ice might take longer to freeze. This 115-volt 60Hz evaporator fan motor measures approximately 6.75 inches deep, 3.25 inches wide and 2.5 inches high. Do not forget to disconnect the power to the refrigerator before you begin this repair.
Fixes these symptoms
  • Clicking sound
  • Freezer section too warm
  • Fridge and Freezer are too warm
  • See more...
Installation Instructions
Francis from Rochester, NY
Noisey fan
Unplug power, remove several parts to access the fan motor located at the back of the freezer section. Disconnect fan motor. Remove impeller from motor shaft. Reassemble all parts. Very easy repair. Read more...
$17.00
  In Stock
Drum Bearing Slide - White
★★★★★
★★★★★
(1)
Fix Number FIX755842
Manufacturer Part Number WE1M504
This single drum bearing slide attaches to the outer-most side of the bearing. This part is also sometimes referred to as a drum slide, drum glide, or drum pad. It provides support to the front of the drum as it rotates. They are approximately 3-inches long, 1 inch wide and made from a durable white plastic. If your appliance starts making unusual sounds, is not drying clothes properly, or leaves marks on clothes, it may be time to replace this part. The dryer has 2 slides, which we recommend replacing at the same time, as they tend to wear out at the same rate. You will need to order 2 of this part to replace both drum bearing slides, since it is sold individually. Before you begin this repair, be sure to disconnect the power to the dryer.
Fixes these symptoms
  • Marks left on clothes
  • No heat or not enough heat
  • Noisy
  • See more...
Installation Instructions
Donald L. from Belmont, MA
Dark marks on clothing; clothing sticking between drum and front panel
Others with the same problem of dark marks on clothing suggested replacing the white and the grey drum slides that slip into the front drum bearing unit. When I open up the dryer, I did find that both the white and grey drum slides on one side of the front drum bearing piece had completely worn away, and some of the drum bearing piece was also worn away. I had decided in advance to order both white slides, both grey slides, a new felt seal, and the front drum bearing piece. Possibly I could have reused the old front drum bearing, but the replacement was cheap enough. Three bits of advice: 1) if you replace the felt seal, make sure you get it tucked behind the clips on the door panel; 2) if you replace the front drum bearing piece, once you have the dryer put back together, reach up and pull the plastic drum bearing toward you to be sure it is fully snapped into place; 3) after you replace the slides or felt, the drum will make mild rubbing noises as it turns, so run the dryer with no heat for about 30 minutes to seat the parts. Read more...
$11.49
  In Stock
Drum Bearing Slide - Green
★★★★★
★★★★★
(2)
Fix Number FIX6447706
Manufacturer Part Number WE1M1067
This single drum bearing slide is an OEM approved replacement part for dryers. It can also be known as a bearing drum slide, pad, or glide. The slides attach to the inner most slots on the front bearing. As the dryer rotates, the drum bearing slides help to support the front of the drum. If your appliance becomes noisy, is not drying properly, or leaves marks on clothes, it may be time to replace it. If you are replacing one slide, we recommend replacing the other slide at the same time, as they deteriorate at a similar rate. You will need to order 2 of these parts as there are 2 in each dryer. It is approximately 2.6-inches deep, 0.06-inches in height, and 0.5-inches wide. This part is denoted as being green in the title, however users and technicians have noted it is actually gray in color.
Fixes these symptoms
  • Marks left on clothes
  • No heat or not enough heat
  • Noisy
  • See more...
Installation Instructions
Donald L. from Belmont, MA
Dark marks on clothing; clothing sticking between drum and front panel
Others with the same problem of dark marks on clothing suggested replacing the white and the grey drum slides that slip into the front drum bearing unit. When I open up the dryer, I did find that both the white and grey drum slides on one side of the front drum bearing piece had completely worn away, and some of the drum bearing piece was also worn away. I had decided in advance to order both white slides, both grey slides, a new felt seal, and the front drum bearing piece. Possibly I could have reused the old front drum bearing, but the replacement was cheap enough. Three bits of advice: 1) if you replace the felt seal, make sure you get it tucked behind the clips on the door panel; 2) if you replace the front drum bearing piece, once you have the dryer put back together, reach up and pull the plastic drum bearing toward you to be sure it is fully snapped into place; 3) after you replace the slides or felt, the drum will make mild rubbing noises as it turns, so run the dryer with no heat for about 30 minutes to seat the parts. Read more...
$9.92
  In Stock
Evaporator Fan Grommet - Red
Fix Number FIX963756
Manufacturer Part Number WR02X12008
The evaporator fan grommet is used to provide a cushion between the fan motor and the motor mounting bracket in your freezer. This genuine OEM part is about one inch in diameter and is red in color. It is part of the motor assembly found behind the evaporator fan cover at the back of your freezer. If the fan has become quite noisy, it may be time to replace the grommet. To complete this repair, you will need to remove everything from the freezer including the ice tray, the fan cover, freezer floor, evaporator cover, and the fan motor assembly. The tools you will need for this job include a pair of needle nose pliers, a Philips screwdriver and a small flat blade screwdriver, along with a 1/4-inch and a 5/16-inch nut driver. Please ensure that you disconnect the power supply to your fridge before you begin this repair.
Fixes these symptoms
  • Clicking sound
  • Freezer section too warm
  • Fridge too warm
  • See more...
Installation Instructions
Michael from Burlington, MA
Fan was missing a left bumper from manufacturer & causing noise/vibration
Unplugged refrigerator then emptied freezer and removed wire shelf. In back removed phillip head screws. Removed circulation cowling & carefully pulled up and out styrofoam insert. Removed fan bracket & unplugged unit from tabs. Replaced front & back grommets and lid bumpers. Eliminated excessive noise from fan due to heavy vibration. Read more...

Appliance Type

Popular Hotpoint Models