Hotpoint Refrigerator Parts

Start With Your Model Number

Need help finding your model number?

Find Parts Fast

Guaranteed Fit

Repair Videos

Water Filter Finder

Popular Hotpoint Refrigerator Parts

Watch the install video

Refrigerator Ice and Water Filter

$73.01

In Stock

Add to cart

Fix Number

FIX8746144

Manufacturer Part Number

MWFP

This is an OEM replacement water filter for your refrigerator. The manufacturer suggests replacing this filter every 6 months or 300 gallons of water. If not replaced regularly, you will risk contaminants getting into your water, and poor performance of your water dispenser and/or icemaker. This filter has a twist and lock design, making the replacement of this part very simple and tool-free. Please note that the manufacturer has updated this filter, so if this is the first time installing it you may require an adapter, which is sold separately. If your model has a reset button, do not forget to hold it down for a few seconds to reset the indicator once you?ve replaced this part. Adapter, PartSelect #: PS220347

Fixes these symptoms

• Ice maker dispenses too little ice
• Ice maker not making ice
• Ice maker won’t dispense ice
• See more...

Installation Instructions

saul from wylie, TX

the fridge would not stay cool

Replace the termostat and temp sensor for those two you have to cut and splice new wires. And the water filter easy twist off and twist back on for the heater and braket assembly it was pull out old and place new maybe hour long job Read more...

Watch the install video

Evaporator Fan Motor

$74.36

In Stock

Add to cart

Fix Number

FIX12741350

Manufacturer Part Number

WR60X31522

This is an evaporator fan motor, located in the freezer compartment. It is sold as a single unit. It is responsible for moving air over the evaporator coils as the compressor is running. When this part is faulty you may hear loud sounds coming from the freezer area, your refrigerator may not stay as cold as normal, or the ice might take longer to freeze. This 115-volt 60Hz evaporator fan motor measures approximately 6.75 inches deep, 3.25 inches wide and 2.5 inches high. Do not forget to disconnect the power to the refrigerator before you begin this repair.

Fixes these symptoms

• Clicking sound
• Freezer section too warm
• Fridge and Freezer are too warm
• See more...

Installation Instructions

Francis from Rochester, NY

Noisey fan

Unplug power, remove several parts to access the fan motor located at the back of the freezer section. Disconnect fan motor. Remove impeller from motor shaft. Reassemble all parts. Very easy repair. Read more...

Watch the install video

BUCKET AUGER

$72.49

In Stock

Add to cart

★★★★★

★★★★★

1 Review

Fix Number

FIX17626595

Manufacturer Part Number

WR29X43990

If the ice maker in your fridge is noisy or no longer dispensing ice, there may be an issue with the auger in the ice bucket. The auger works by spinning to pull and dispense ice from the bin down the ice chute and into your glass. Regular use of the auger over time can cause it to wear down, and if ice is allowed to build up it can also cause the auger to break. When replacing this part, you will need to remove the entire icemaker assembly from your freezer. Be sure to turn the ice maker off before beginning this repair. As the ice maker assembly is made of plastic, we suggest allowing it to warm up before starting any work, to prevent cracking and further damage. This is a genuine OEM part and is made of clear plastic and metal.

Fixes these symptoms

• Engine revs but auger will not turn
• Engine runs but cutters do not turn
• Ice maker dispenses too little ice
• See more...

Installation Instructions

Donald from COLTS NECK, NJ

ice dispenser auger was broken

UTUBE was a great help. Your service is outstanding. I dropped the broken auger cutters and washers. The utube was clear enough for me to get the correct order for proper repair. Most of the hour plus was spent on this drop of parts. Read more...

Module Shelf Insert - Clear

$21.25

In Stock

Add to cart

Fix Number

FIX2323438

Manufacturer Part Number

WR71X10761

This is an OEM clear plastic module shelf insert (door shelf trim), which is the part of the door shelf bin that snaps onto the front to keep items contained securely on the shelf. This is the shelf insert only, the door bin is sold separately. Due to the cold conditions of your refrigerator, this part can crack or break over time, and will need to be replaced. Simply snap the insert onto the door bin using the locking tabs, and your repair is complete, no tools necessary.

Installation Instructions

Zabelle from Las Cruces, NM

Insert shattered from extreme heat in garage

Easy as pie, just slid it into place and I was done, piece of cake!! Read more...

Light Bulb - 40W

$11.01

In Stock

Add to cart

Fix Number

FIX217532

Manufacturer Part Number

40A15

This 40-Watt light bulb is sold individually and is a genuine OEM replacement option for your home appliances. It is specially designed to withstand extreme temperatures, so this bulb is compatible with a variety of appliance types including refrigerators, ranges, microwaves, and dryers. It features a frosted glass bulb with a standard metal socket base, which allows you to easily unscrew the burnt-out light and twist the new bulb into place. Depending on your appliance, there may be a guard or cover protecting the lightbulb, in which case you may require additional tools to remove the cover. We recommend disconnecting the power supply to your appliance before changing the lightbulb.

Installation Instructions

Jeffrey from SEATTLE, WA

Bake element replacement

1. Turn of over power at the breaker.
2. Remove bake element cover. There's 2 quarter inch nuts.
3. Disconnect old element. For me there was not much play in the wires so when I disconnected the old element I lost the wire in the insulation. If this happened you can remove the central plate cover on the back of the oven and you can easily find the wires again.
4. Connect the replacement element.
5. Screw the bake element cover back in.
6. Turn power back on. Read more...

Glass Shelf

$31.91

In Stock

Add to cart

★★★★★

★★★★★

1 Review

Fix Number

FIX11699574

Manufacturer Part Number

WR32X21260

This is a genuine replacement glass shelf for your refrigerator. It measures 21 by 13 inches and sits above the two crisper drawers. If the shelf has become cracked or damaged it should be replaced so that your fridge is fully functional. To replace the glass, simply lift the old piece up and out of the frame, and insert the new one in its place. Please note that this part is just the glass shelf, if you need a new shelf frame it will need to be purchased separately.

Watch the install video

Door Shelf Bar

$30.10

In Stock

Add to cart

★★★★★

★★★★★

1 Review

Fix Number

FIX964507

Manufacturer Part Number

WR17X11889

This fixed shelf is made of white plastic, approximately 24 inches wide, and fastens to your fridge door to hold items in place. Regular wear and tear can cause the shelf bar to become damaged over time. If the shelf on your refrigerator door has become cracked, broken, or is missing entirely, it is time for a replacement. Replacing this genuine OEM part is an easy repair that does not require any tools. Simply pop out the old shelf bar, line up the new one and snap into place ensuring the locking tabs are secured.

Installation Instructions

Hazel from Wheatley Heights, NY

The rack cracked that holds the drawers

I removed all the contents of the drawers and replaced the tempered glass and I was finished!! Read more...

Watch the install video

Temperature Sensor

$26.97

In Stock

Add to cart

★★★★★

★★★★★

1 Review

Fix Number

FIX304103

Manufacturer Part Number

WR55X10025

The temperature sensor, also referred to as a thermistor, is used to monitor the refrigerator and freezer internal temperatures. The sensor is a small capsule like device that is protected by a white plastic casing. The sensor sends the temperature reading to the control board, which uses this information to turn on the compressor and fan circuits. If this part is malfunctioning it may inaccurately signal the control board to turn off these components, resulting in warmer than normal temperatures in the fresh food and freezer sections. This part can break from material fatigue through normal use, and will need to be replaced when this happens. You will find this part attached to the evaporator and control housing in your appliance. This OEM part measures roughly 1.25 inches with 18-inch long wire leads. For this repair, you will need a 1/4 inch nut driver, a pair of strippers and crimpers, and a pair of wire splice connectors.

Fixes these symptoms

• Doesn’t stop running
• Freezer not defrosting
• Freezer section too warm
• See more...

Installation Instructions

Steven from Indio, CA

Fresh food section not cooling

Online info suggested thermal sensor was the issue (coils cleaned, fans functional). I ordered the part and received it in 2 days. Finding the sensor was the issue. I removed the shelves, then removed a temp control knob, the lights and the protective panel covering them. I removed a long white panel (no screws), removed two panels (one with 2 screws, one with three screws. The thermal sensor was behind the last panel removed. The cooling coils with the thermal sensor were covered with a styrofoam like device. Used a hair dryer to melt the ice. The new sensor was then put in place as per other videos on this topic. It took longer to melt the ice then to remove the panels giving access to the sensor. All in all a pretty easy repair. BTW, refrigerator is working fine (0-2F in freezer, 37F in fresh foods side). Read more...

Watch the install video

WATER VALVE WITH GUARD

$93.74

In Stock

Add to cart

★★★★★

★★★★★

2 Reviews

Fix Number

FIX16226572

Manufacturer Part Number

WR57X33326

This double inlet water valve has quick connections. This valve has 1/4 and 5/16 John Guest fittings for the outlet lines and a 1/4 compression fitting for the inlet line.

Fixes these symptoms

• Ice maker not making ice
• Ice maker won’t dispense ice
• Leaking
• See more...

Installation Instructions

Mark from Haymarket, VA

Water Dispenser would not dispense water

Watched installation video and read other comments and instructions by others who changed part. Turned water off at the main in my utility room. There is a valve behind the unit in the supply line, but was not sure of the reliability of the old valve (11 years) having read about it online and problems with it. Figured if I didn't open and close valve could save myself aggravation of old and perhaps leaky valve. Turned on a couple taps to release water pressure so I didn't have to deal with pressure at supply tubes. Unplugged unit. Did not have 5/16 nut drive, so removed screws with pliers from lower cover and lifted out. Found dual inlet water valve readily and removed screw retaining unit. Disconnected electrical connections. One was sticky and used pliers to pull off connecter taking care not to pull on wires. Took out water lines by depressing connnectors. Had towel handy to catch minimal drips. Used utility knife to trim supply lines by 1/2 inch before reinserting to ensure square seating. Attached electrical leads and inserted water lines and reattached to frame. Turned on water and no leaks. Took minute to vacuum dust from motor at bottom right of unit and other accumulations inside to promote cooling and function. Replaced cover on unit. However, this did not fix problem. Did additional search online and found thread that noted frozen water line in freezer door because of design flaw. Used hair dryer inside and outside freezer door along line a few times being careful not to melt plastics. After doing a few times, water came back on. I think it was a combination of replacing the valve and thawing the line that returned the water dispenser to functioning properly. I like this site and have used before on this fridge to replace heater in freezer compartment. Figure I have saved several hundred dollars and time and necessity of waiting on repairman for something I can do. Will always consult this site if I have an appliance problem. Read more...

Evaporator Fan Grommet - Red

$13.20

In Stock

Add to cart

Fix Number

FIX963756

Manufacturer Part Number

WR02X12008

The evaporator fan grommet is used to provide a cushion between the fan motor and the motor mounting bracket in your freezer. This genuine OEM part is about one inch in diameter and is red in color. It is part of the motor assembly found behind the evaporator fan cover at the back of your freezer. If the fan has become quite noisy, it may be time to replace the grommet. To complete this repair, you will need to remove everything from the freezer including the ice tray, the fan cover, freezer floor, evaporator cover, and the fan motor assembly. The tools you will need for this job include a pair of needle nose pliers, a Philips screwdriver and a small flat blade screwdriver, along with a 1/4-inch and a 5/16-inch nut driver. Please ensure that you disconnect the power supply to your fridge before you begin this repair.

Fixes these symptoms

• Clicking sound
• Freezer section too warm
• Fridge too warm
• See more...

Installation Instructions

Michael from Burlington, MA

Fan was missing a left bumper from manufacturer & causing noise/vibration

Unplugged refrigerator then emptied freezer and removed wire shelf. In back removed phillip head screws. Removed circulation cowling & carefully pulled up and out styrofoam insert. Removed fan bracket & unplugged unit from tabs. Replaced front & back grommets and lid bumpers. Eliminated excessive noise from fan due to heavy vibration. Read more...

Hotpoint Refrigerator Appliance Types

• Refrigerator Parts
• Hotpoint Parts

Related Hotpoint Refrigerator Parts

• Hotpoint Refrigerator Brackets and Flanges
• Hotpoint Refrigerator Caps and Lids
• Hotpoint Refrigerator Circuit Boards and Touch Pads
• Hotpoint Refrigerator Compressors
• Hotpoint Refrigerator Dispensers
• Hotpoint Refrigerator Door Shelves
• Hotpoint Refrigerator Doors
• Hotpoint Refrigerator Drawers and Glides
• Hotpoint Refrigerator Elements and Burners
• Hotpoint Refrigerator Handles
• Hotpoint Refrigerator Hardware
• Hotpoint Refrigerator Hinges
• Hotpoint Refrigerator Hoses and Tubes
• Hotpoint Refrigerator Ice Makers
• Hotpoint Refrigerator Lights and Bulbs
• Hotpoint Refrigerator Motors
• Hotpoint Refrigerator Seals and Gaskets
• Hotpoint Refrigerator Springs and Shock Absorbers
• Hotpoint Refrigerator Switches
• Hotpoint Refrigerator Thermostats
• Hotpoint Refrigerator Trays and Shelves
• Hotpoint Refrigerator Valves

Popular Hotpoint Refrigerator Models

• HTS18GBSARWW Top Freezer S Series
• HSS25GFPJWW Side-by-side P Series
• HSM25GFTASA Side-by-side T Series
• HSS25GFTAWW Side-by-side T Series
• HSM25GFRFSA Side-by-side R Series
• HSS25GFPAWW Side-by-side P Series
• HTS17GBSERWW Top Freezer S Series
• HSS25IFMDWW Side-by-side M Series
• HSS25GFPHWW Side-by-side P Series
• HSM25GFRESA Side-by-side R Series
• HSS25GFTABB Side-by-side T Series
• HTS17GBSARWW Top Freezer S Series
• HSM25GFRASA Side-by-side R Series
• HSS25GFPDWW Side-by-side P Series
• HTS22GBPBRWW Top Freezer P Series
• HTS15BBMFRWW Top Freezer M Series
• HSM25GFTCSA Side-by-side T Series
• HTS16GBRFRWW Top Freezer R Series
• HSH25GFBBBB
• CTX14CYXKRWH Top Freezer X Series