Dryer Bearings

★★★★★

★★★★★

2 Reviews

Fix Number

FIX6447706

Manufacturer Part Number

WE1M1067

This single drum bearing slide is an OEM approved replacement part for dryers. It can also be known as a bearing drum slide, pad, or glide. The slides attach to the inner most slots on the front bearing. As the dryer rotates, the drum bearing slides help to support the front of the drum. If your appliance becomes noisy, is not drying properly, or leaves marks on clothes, it may be time to replace it. If you are replacing one slide, we recommend replacing the other slide at the same time, as they deteriorate at a similar rate. You will need to order 2 of these parts as there are 2 in each dryer. It is approximately 2.6-inches deep, 0.06-inches in height, and 0.5-inches wide. This part is denoted as being green in the title, however users and technicians have noted it is actually gray in color.

★★★★★

★★★★★

3 Reviews

Fix Number

FIX459829

Manufacturer Part Number

5303281153

This ball-and-socket style bearing kit is used in your dryer to support the rear of the drum as it tumbles through the dry cycle. The bearing attaches on the inside of the rear panel of the dryer cabinet. Over time, the bearing or the bushing can wear out, and the ball support can become damaged. If these things happen, your dryer may not tumble, or it will be noisy while operating. If this is the case, you may need to replace these parts. This genuine OEM parts kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high-temperature lubricant, and the installation screws. Completing this repair requires taking the entire drum out of your dryer along with handling greasy parts, so have a rag handy for cleanup. Please ensure that you disconnect the power supply to your appliance before beginning this repair.

Fix Number

FIX418807

Manufacturer Part Number

131825900

The drum support bearing is an authentic OEM replacement part for your dryer. The bearing is used to support the drum and allow it to rotate smoothly and quietly. If your dryer is excessively noisy while tumbling, will not start, will not tumble, or if it is leaving marks on your laundry, you may need to replace the drum support bearing. The bearing is found on the inside of the rear panel of the dryer cabinet, and you will need to remove the drum in order to complete this repair. Please be sure to disconnect the power supply to your dryer before you begin.

★★★★★

★★★★★

1 Review

Fix Number

FIX267529

Manufacturer Part Number

WE25M40

This rear drum bearing kit is a genuine OEM replacement for your dryer. The kit includes a shaft, ground strap, bracket, bearing and seven screws for installation. The bearing supports that back of the dryer drum and helps to reduce friction so that the drum can rotate smoothly and quietly. If the bearing has worn out, it can result in your dryer not tumbling, or making excessive noise when it is running.

Fix Number

FIX266777

Manufacturer Part Number

WE1M462

Sold individually.

Fix Number

FIX1766010

Manufacturer Part Number

WE14M124

The drum slides are not included with this part. The top bearing helps your dryer operate as quietly as possible. This part will require two green drum slides and 2 white drum slides.

Fix Number

FIX12579101

Manufacturer Part Number

131724301

This drum bearing bracket is for dryers. Drum bearing bracket holds and supports the drum bearing

Fix Number

FIX459830

Manufacturer Part Number

5303281154

This is a flat style ridgeless dryer belt.

Fix Number

FIX11740802

Manufacturer Part Number

WP315772

This sleeve is less than an inch in diameter. It is made of metal and is intended for use with the screw that holds the idler pulley of your clothes dryer.

Fix Number

FIX267877

Manufacturer Part Number

WE3X87

This slide is sold individually. Some dryers require up to three of these slides . Be sure to check to make sure you order the necessary amount for your dryer.