Samsung Dryer Parts

Start With Your Model Number

Need help finding your model number?
Find Parts Fast
Guaranteed Fit
Repair Videos
Fix.com search
Samsung Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular Samsung Dryer Parts

Heating Element - 5300W – Part Number: DC47-00019A
Heating Element - 5300W
$84.53
In Stock
Fix Number
FIX4205218
Manufacturer Part Number
DC47-00019A
Includes the insulators and restring already attached. This dryer heating element produces heat to dry clothes in a dryer and is located in the rear end. If the heater element is burned, dryer does not heat or over heats, or clothes take too long to dry, then replacing this part could solve your problem. The tools needed for this repair project are: Phillips screwdriver, putty knife, needle nose pliers. To repair, first remove the main top of dryer and remove ground strap at the rear. Next, disconnect two wire harnesses that hold front panel to the cabinet to pull out front panel. Once you have access to the inside of the dryer, refer to the manual for further installation instruction. As a safety precaution, remember to unplug appliance from power source before beginning this repair project.
Fixes these symptoms

Installation Instructions

Jay from Battle Creek, MI
No heat
Unplug unit. Pull top off, pulled front top panel, pulled the front panel with door. Remove rear exhaust tube. Removed wires to heating element, remove heating element housing. Open heating element housing and remove element. Bend terminals to remove wires of element from housing. Reverse above steps to reassemble. Read more...
Watch the install video
Drum Support Roller & Axle – Part Number: DC97-16782A
Drum Support Roller & Axle
$60.42
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX4221885
Manufacturer Part Number
DC97-16782A
This dryer drum support roller and axle assembly includes the roller shaft and mounting clips, and is designed to support the drum as it rotates during operation. Engineered for durability and smooth performance, the roller is self-lubricating and does not require additional grease. If your dryer is producing unusual noises, worn rollers may be the cause. This part is sold individually and should be installed with the appliance unplugged. Refer to the manufacturer’s diagram and instructions for proper installation.
Fixes these symptoms
Watch the install video
Thermal Fuse – Part Number: DC47-00016A
Thermal Fuse
$28.78
In Stock
Fix Number
FIX4205213
Manufacturer Part Number
DC47-00016A
This replacement thermostat is designed for use with electric dryers to help regulate and maintain the correct temperature during each drying cycle. A properly working thermostat ensures that the heating element shuts off at the right time, preventing overheating that could damage clothing or, in severe cases, create a fire hazard. If your dryer is not shutting off the heat when it should, this thermostat may be the part you need. Installation requires disconnecting the appliance from its power source for safety, and the thermostat is secured inside the dryer with two screws, which are sold separately.
Fixes these symptoms

Installation Instructions

Richard from Marysville, WA
no heat, burned out heater element,
UNPLUG first! remove vent hose, remove inside vent tube, (three screws), remove the top panel, (two screws, on back top), remove front panel with door,(4 screws on top, & 3 screws inside door)..to remove heater, remove one screw in the front, and unplug the wiring, then snake it out the back.. install new and put back together following steps back to start!! Read more...
Watch the install video
Drive Belt – Part Number: 6602-001655
Drive Belt
$56.05
In Stock
Fix Number
FIX4133825
Manufacturer Part Number
6602-001655
This black rubber drum belt connects the motor pulley to the dryer drum, enabling the drum to rotate as the motor runs. Positioned between the drive motor and the drum, it plays a key role in the drying process. If the belt breaks or wears out, the drum may stop turning properly. Replacing the belt is a straightforward repair that typically takes only a few minutes. To install, pull the dryer away from the wall, remove the rear panel using a Phillips screwdriver, and position the new belt around the motor pulley and drum. Each belt is sold individually.
Fixes these symptoms

Installation Instructions

Cynthia from Skillman, NJ
Dryer belt broke
I found a video showing how to take apart my machine and followed it. So glad I did. The part came quickly and the repair took a little over an hour. No issues. Much better than waiting for and paying a repair man. Read more...
Watch the install video
Dryer Radiant Flame Sensor – Part Number: WP338906
Dryer Radiant Flame Sensor
$36.42
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX11741429
Manufacturer Part Number
WP338906
This genuine OEM part is a radiant flame sensor for your gas dryer. It is used to determine when the temperature of the igniter is hot enough to ignite the gas. Once the igniter is hot enough, it allows the valve to open to release the gas. This acts as a safety mechanism which prevents dangerous levels of gas from building up. If your dryer will not start, is not producing enough heat, not heating up at all, is taking too long to dry laundry, or is shutting off too soon, you may need to replace the radiant flame sensor. Please be sure to disconnect the power and gas supply to your dryer before beginning this repair.
Fixes these symptoms

Installation Instructions

William from Corsicana, TX
Oor dryer would not get hot.
I opened the bottom section and watched as the igniter got red hot as it should but the gas valve did not open. I wired around the sensor and the gas valve opened and the fuel ignited. VERY IMPORTANT: DO NOT RUN YOUR DRYER IN THIS STATE: IT WILL BLOW UP!! I did a VERY short test, then ordered the new sensor. Just one screw holds the sensor (as shown in the Parts video). One screw out, new sensor, one screw in and our dryer is back in full and proper running order. Read more...
Watch the install video
Thermistor – Part Number: DC32-00007A
Thermistor
$37.34
In Stock
Fix Number
FIX4204984
Manufacturer Part Number
DC32-00007A
Fixes these symptoms

Installation Instructions

Richard from Marysville, WA
no heat, burned out heater element,
UNPLUG first! remove vent hose, remove inside vent tube, (three screws), remove the top panel, (two screws, on back top), remove front panel with door,(4 screws on top, & 3 screws inside door)..to remove heater, remove one screw in the front, and unplug the wiring, then snake it out the back.. install new and put back together following steps back to start!! Read more...
Filter Case – Part Number: DC61-02610A
Filter Case
$30.95
In Stock
Fix Number
FIX4206806
Manufacturer Part Number
DC61-02610A
High Limit Thermostat - L260-50F – Part Number: DC47-00018A
High Limit Thermostat - L260-50F
$49.87
In Stock
Fix Number
FIX4205217
Manufacturer Part Number
DC47-00018A
Fixes these symptoms

Installation Instructions

Richard from Marysville, WA
no heat, burned out heater element,
UNPLUG first! remove vent hose, remove inside vent tube, (three screws), remove the top panel, (two screws, on back top), remove front panel with door,(4 screws on top, & 3 screws inside door)..to remove heater, remove one screw in the front, and unplug the wiring, then snake it out the back.. install new and put back together following steps back to start!! Read more...
Watch the install video
Heater Duct Assembly w/ Thermostats – Part Number: DC97-14486A
Heater Duct Assembly w/ Thermostats
$277.18
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX4220205
Manufacturer Part Number
DC97-14486A
This genuine OEM heater duct assembly in your dryer directs hot air into the drum during operation. Generally, it can be found behind the drum or at the rear of the dryer. If this assembly becomes damaged, you may encounter problems such as clothes not drying properly or drying unevenly. This kit includes the housing with the heating element coil and attached insulators.
Fixes these symptoms
Watch the install video
Idler Pulley Assembly – Part Number: DC93-00634A
Idler Pulley Assembly
$62.63
In Stock
Fix Number
FIX11771601
Manufacturer Part Number
DC93-00634A
This idler pulley assembly includes the pulley wheel and bracket, and is located near the motor in compatible dryer models. It maintains tension on the dryer belt, allowing the drum to rotate smoothly during cycles. Over time, wear on the pulley or its bearings can cause squeaking, grinding, or belt misalignment. If left unchecked, this can prevent the drum from turning altogether. To replace, disconnect power, access the pulley by disassembling the dryer, remove the old assembly, and install the new one. Ensure the belt is properly threaded and tensioned before reassembling the appliance.
Fixes these symptoms

Samsung Dryer Appliance Types

Related Samsung Dryer Parts

Popular Samsung Dryer Models

View More
+