Samsung Parts

Samsung Appliance Parts

Popular Samsung Parts

★★★★★
★★★★★
3 Reviews
Fix Number
FIX4163672
Manufacturer Part Number
DA81-01345B
This OEM door mullion spring is found in French door style refrigerators, and is used to apply tension between components in the fridge doors. The spring engages and retracts the door flap, which allows the door to close properly. To replace this part, you will need a pair of needle nose pliers to remove the old spring from the mullion, and insert the new one in its place. A sign you should have this part replaced is if the door does not close properly due to the door flap swinging freely.
Fixes these symptoms

Installation Instructions

Chuck from FALLSTON, MD
LEFT SIDE DOOR FLAP WOULD NOT TURN IN WHEN CLOSING
Step 1: Opened up beer and drank a couple times.
Step 2: Put in spring at top end and tried to insert into bottom end. That did not work so I finished my beer and opened up another one! Put spring in at bottom, then inserted into top and it went it perfectly. Closed door and it closed properly. Drank some beer and opened and close door praising myself for fixing it myself. Could not believe that I paid more for the shipping than the part itself!
Read more...
Affresh Washing Machine Cleaner - 3 pack
$12.58
In Stock
Fix Number
FIX1960673
Manufacturer Part Number
W10135699
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
Long Oven Sensor
$34.72
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX1570174
Manufacturer Part Number
12001656
This is a factory-certified oven sensor kit with two harness adapters. Its purpose is to sense the temperature inside the oven. Replacing this part can fix an oven that is not reaching the proper temperature (too hot or not hot enough), not heating evenly, or an oven that will not start. To access this part, you will need access to the back of the range. Use a Phillips screwdriver to remove the screws on the access panel. Once the access panel is removed, you will notice a hole on the right side of the oven where the temperature sensor comes out of the oven. You will need to unplug the wire harness, and then open the oven door, locate it in the upper left corner, and remove the screws holding the temperature sensor in place. Pull the sensor out of the back of the oven, and replace it with your new part.
Fixes these symptoms
  • Door won’t open after self cleaning cycle
  • Element will not heat
  • Little to no heat when baking
  • See more...

Installation Instructions

Michael from Pearl River, NY
Oven did not heat up
Removed the oven door, removed existing screws. Pulled wire carefully out of opening, unclip connection. Reattached connection screwed back new sensor attached oven door finished. Read more...
★★★★★
★★★★★
1 Review
Fix Number
FIX4221885
Manufacturer Part Number
DC97-16782A
Sold individually.
Fixes these symptoms
★★★★★
★★★★★
1 Review
Fix Number
FIX11741429
Manufacturer Part Number
WP338906
This genuine OEM part is a radiant flame sensor for your gas dryer. It is used to determine when the temperature of the igniter is hot enough to ignite the gas. Once the igniter is hot enough, it allows the valve to open to release the gas. This acts as a safety mechanism which prevents dangerous levels of gas from building up. If your dryer will not start, is not producing enough heat, not heating up at all, is taking too long to dry laundry, or is shutting off too soon, you may need to replace the radiant flame sensor. Please be sure to disconnect the power and gas supply to your dryer before beginning this repair.
Fixes these symptoms

Installation Instructions

William from Corsicana, TX
Oor dryer would not get hot.
I opened the bottom section and watched as the igniter got red hot as it should but the gas valve did not open. I wired around the sensor and the gas valve opened and the fuel ignited. VERY IMPORTANT: DO NOT RUN YOUR DRYER IN THIS STATE: IT WILL BLOW UP!! I did a VERY short test, then ordered the new sensor. Just one screw holds the sensor (as shown in the Parts video). One screw out, new sensor, one screw in and our dryer is back in full and proper running order. Read more...
Drive Belt
$50.13
In Stock
Fix Number
FIX4133825
Manufacturer Part Number
6602-001655
Fixes these symptoms

Installation Instructions

Cynthia from Skillman, NJ
Dryer belt broke
I found a video showing how to take apart my machine and followed it. So glad I did. The part came quickly and the repair took a little over an hour. No issues. Much better than waiting for and paying a repair man. Read more...
Heating Element - 5300W
$89.62
In Stock
Fix Number
FIX4205218
Manufacturer Part Number
DC47-00019A
Includes the insulators and restring already attached. This dryer heating element produces heat to dry clothes in a dryer and is located in the rear end. If the heater element is burned, dryer does not heat or over heats, or clothes take too long to dry, then replacing this part could solve your problem. The tools needed for this repair project are: Phillips screwdriver, putty knife, needle nose pliers. To repair, first remove the main top of dryer and remove ground strap at the rear. Next, disconnect two wire harnesses that hold front panel to the cabinet to pull out front panel. Once you have access to the inside of the dryer, refer to the manual for further installation instruction. As a safety precaution, remember to unplug appliance from power source before beginning this repair project.
Fixes these symptoms

Installation Instructions

Jay from Battle Creek, MI
No heat
Unplug unit. Pull top off, pulled front top panel, pulled the front panel with door. Remove rear exhaust tube. Removed wires to heating element, remove heating element housing. Open heating element housing and remove element. Bend terminals to remove wires of element from housing. Reverse above steps to reassemble. Read more...
Spring PIN - French
$4.66
In Stock
Fix Number
FIX4163673
Manufacturer Part Number
DA81-01346A
Refrigerator PIN-FRENCH door SPRING;RD-PVC
Fixes these symptoms
Fix Number
FIX11771601
Manufacturer Part Number
DC93-00634A
Fixes these symptoms
Light Bulb - 10W
$16.30
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX11739347
Manufacturer Part Number
WP22002263
This ten watt appliance light bulb is two inches tall. It is used with both washers and dryers.

Installation Instructions

David from Myrtle Beach, SC
Dryer would squeek loudly
Removed door, and front bezel. Write the colors of the wires next to the door switch and the moisture sensor on the bezel so that you can remove the wires, this makes it easier. Lifted top up and pulled drum out, but did not remove belt. Inspected wheels and roller shaft. Needed to replace (2) Roller Wheels, (1) Roller Shaft, (2) Retaining Rings, & (2) Shaft Washers. Ordered parts from the site. Removed the Retaining rings. The retaining ring tool I bought from the hardware store did not fit the holes in the retaining ring, so I had to file the tips down. Once the retaining rings are removed, the washers and rollers come off easily. The Roller Shaft can be removed by loosening the nut on the back side of the shaft. Inserted new shaft and tightened nut, then replaced both rollers, and washers, and reinstalled the Retaining rings. Put drum back in place, tied all wires back in and reinstalled front bezel and door. Read more...

Samsung Appliance Types

Popular Samsung Models