Models > NX58H5600SS

NX58H5600SS ((AC)(0001)) Samsung Range

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
In Stock
$84.34
In Stock
On Order
On Order
In Stock
Sold individually.
In Stock
In Stock
Special Order
The burner cap protects the burner head from spills and helps spread out the burner flame for even heating.
In Stock
In Stock
In Stock
In Stock

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Problems and Symptoms for NX58H5600SS

Viewing 5 of 5
Doesn’t shut off
Fixed by these parts
Fixing
How to fix it
Little to no heat when baking
Fixed by these parts
Fixing
How to fix it
No heat
Fixed by these parts
Fixing
How to fix it
Gas igniter glows, but will not light
Fixed by these parts
Fixing
How to fix it
Won’t turn on
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
  • Customer:
    John from EAST QUOGUE, NY
  • Parts Used:
    DG94-00520A
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Oven not heating and holding temp
The Samsung stove I have has had the igniter replaced several times. It seems to wear out over a couple years time. I did the repair with a Philips #2 screw driver. Open the oven door, remove the grates. unscrew the bottom cover and expose the heat shield. Unscrew the heat shield. This exposes the burner. Unscrew the burner from the center of the plate/lower heat shield. Unscrew the burner from the front and back of the oven. Carefully lift up the burner to expose the igniter and clip. Unscrew the igniter from the burner and set the burner aside. Unclip the igniter from the power cable. If it falls below, it won't go far just reach in a lift it back up to fasten the new igniter to the power clip. Refasten to the burner with new clips and screws provided. Re-insert the burner to the gas jet that is below the bottom plate which will not be visible to you unless you place your head towards the rear of the stove and look down. Once the Jet is back into the hole of the burner, re fasten it to the middle back and front of the stove. Replace the covers and grates. Close the oven and test it. A new igniter does wonders. You can remove the stove door for a less intrusive install, but I found it unnecessary to do so and saved a step and time. I was done well under 30 minutes.
9 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Madeleine from CHICAGO, IL
  • Parts Used:
    DG61-00570A
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
REPLACED THE FLOOR CAVITY
REMOVED THE TWO SCREWS AND THEN THE FLOOR PIECE. THEN REPLACED THE NEW FLOOR CAVITY AND SCREWED THE NEW ONE IN PLACE.
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Raymond from TROY, OH
  • Parts Used:
    3405-001034
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
The microwave would not turn on or would run with the door open
Other tools that are usefull long needle nose pliers, long thin blade screw driver and small magnetic flashlight. Place the microwave on a work bench and remove the case it cover 3 sides. Place the microwave on a chair so it can stand with the controls up. You are replacing the lower door microswitch. The switch is located behind the control panel in the lower part of the area. The switch is several inches inside this area and your hands will not fit. Take care when moving wires and a couple of sensors. Use the thin blade screwdriver to release a tab holding the switch in place. Do not break this tab. Take the needle nose pliers and remove the switch. Put the wires on the new switch, open the door a short distance so a door lever moves enough to put the microswitch back into the bracket.
5 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!