Models
>
GTDP180ED0WW
GTDP180ED0WW General Electric Dryer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for GTDP180ED0WW
Viewing 4 of 4Manuals & Guides for GTDP180ED0WW
Click to downloadInstall
Installation Instructions
(0.83MB)
Manual
Owner's Manuals
(2.01MB)
Manual
Owner's Manuals
(2.47MB)
Keep searches simple, eg. "belt" or "pump".
This single drum bearing slide attaches to the outer-most side of the bearing. This part is also sometimes referred to as a drum slide, drum glide, or drum pad. It provides support to the front of the...
In Stock
This single drum bearing slide is an OEM approved replacement part for dryers. It can also be known as a bearing drum slide, pad, or glide. The slides attach to the inner most slots on the front beari...
Special Order
$34.10
Located on the inside of the dryer front panel, the front drum bearing helps your appliance to operate as quietly as possible. It allows the front of the drum to glide smoothly on the felt seal of the...
In Stock
$22.35
This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromis...
In Stock
$36.10
This 89.5-inch drive belt is for dryers. It has a 4-rib design on the inside for a better grip. If comparing the size of your current belt to the new one, keep in mind that a small amount of stretchin...
In Stock
This knob and clip set is an OEM replacement part for your washer or dryer timer. It is common for this plastic knob to break around the shaft, or for the retainer clip inside the knob to go missing, ...
In Stock
This clip fits inside the control knobs for your laundry machines, and helps to securely fasten the knob to the shaft, which allows you to easily turn the knob to select the correct settings. This is ...
No Longer Available
$70.06
The lint filter is an important component of your dryer, as it traps lint and other debris from entering the dryer vents, where they can become a fire hazard. If your lint filter has become damaged or...
In Stock
$9.24
If the lightbulb inside your dryer drum has burned out, this is an authentic OEM replacement. It is a 10W, 120V bulb that is sold individually. The bulb turns on when the dryer door is open and should...
In Stock
$88.09
This rear drum bearing kit is a genuine OEM replacement for your dryer. The kit includes a shaft, ground strap, bracket, bearing and seven screws for installation. The bearing supports that back of th...
In Stock
In Stock
$111.82
If your dryer will not start, the timer will not advance, or it shuts off too soon, there may be an issue with the dryer timer. If your timer needs to be replaced, this is a genuine OEM part. Please n...
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for GTDP180ED0WW
Viewing 12 of 12Noisy
Fixed by these parts
How to fix it
Marks left on clothes
Fixed by these parts
How to fix it
Door won’t close
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Drum Not Spinning
Fixed by these parts
How to fix it
Won’t Start
Fixed by these parts
How to fix it
Too hot
Fixed by these parts
How to fix it
Timer Not Working
Fixed by these parts
How to fix it
Door latch failure
Fixed by these parts
How to fix it
Touchpad does not respond
Fixed by these parts
How to fix it
Not Heating
Fixed by these parts
How to fix it
Heat stays on after drum has stopped
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Matthew from Plainfield, IL
- Parts Used:
- WE09X27634, WE1M1067, WE1M504
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Due to over loading of the dryer the drum ruined the slides and was making a bad noise due to plastic rubbing plastic
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and
... Read more
drum. I put the new slides in place and installed a new felt strip. I put it back together and that was that. Very easy.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Chicago, IL
- Parts Used:
- WE09X27634, WE05X20431, WE3M26, WE1M504
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer was squeeling when running.
I removed the two screws at the front above the drum opening (with the dryer door open). The top panel then lifts off. I removed the screw at each side that holds the front panel to the side panels, tilted the front panel forward, which disengages the front of the drum from the front drum glide bearing. I then lifted the front panel sl
... Read more
ightly, unhooking the bottom of the panel from the dryer base, and swung the front panel aside. I removed the existing top drum bearing guide, which was disintegrated, and snapped in the new bearing guide, with the nylon slide strips installed in the bearing guide. Next pulled out the old felt strip, and pressed the new one in place. I then put the bottom of the front panel back into the bottom of the dryer front, and while lifting the drum to asure it fit over the bearing guide, pushed the front panel back to a vertical position to mate with the side panels. I then replaced the side panel screws, replaced the top, and replaced the front top panel screws.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Addison, IL
- Parts Used:
- WE3M26, WE09X27634, WE1M1067, WE1M504
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Intermittant squeaking noise
Basically, I followed the same steps a prior person posted.
1.Removed the two screws inside the door, on the top part of the opening.
2.Lifted up and removed the top.
3.Removed two screws holding the front panel in place.
4.Held up the drum while removing the front panel. I carefully turned the panel so I could get at ... Read more the drum bearing without pulling the wires connecting it to the front panel. The wires are not very long, so I had to be careful not to pull on them.
5.Carefully pried off the old drum bearing, using just my hands. It was fairly tight, and popped out just as I started to worry if I was putting too much pressure on it.
6.Checked to see how the old felt was installed, then I pulled out the old felt.
7.Inserted the new felt, being careful to insert one end into a slot the same way the original was installed.
8.Inserted the new slides into the new drum bearing. The gray slides went in at the eleven and one o'clock positions, the white slides went in at ten and two o'clock.
9.Removed a surplus plastic piece from the new drum bearing (where the light comes through).
10.Inserted the new drum bearing, putting the bottom tabs in first, then pivoting it into place. I squeezed it into place to make sure it was tight.
11.Lifted up the drum and put the front panel back on.
12.Screwed the front panel back on, using the two screws.
13.Carefully put the top back on.
14.Screwed in the two screws inside the front door to fasten down the top.
That was it! I started up the dryer and it worked fine. No more squeaking.
About the only thing odd about the repair is why PartSelect sells each slide separately (i.e., I had to order 2 white slides and 2 gray slides). I can't imagine replacing just one, so why not package them in pairs, or maybe even all four in one package.
At any rate, the repair was easy, and a lot cheaper than having someone come out to fix it.
1.Removed the two screws inside the door, on the top part of the opening.
2.Lifted up and removed the top.
3.Removed two screws holding the front panel in place.
4.Held up the drum while removing the front panel. I carefully turned the panel so I could get at ... Read more the drum bearing without pulling the wires connecting it to the front panel. The wires are not very long, so I had to be careful not to pull on them.
5.Carefully pried off the old drum bearing, using just my hands. It was fairly tight, and popped out just as I started to worry if I was putting too much pressure on it.
6.Checked to see how the old felt was installed, then I pulled out the old felt.
7.Inserted the new felt, being careful to insert one end into a slot the same way the original was installed.
8.Inserted the new slides into the new drum bearing. The gray slides went in at the eleven and one o'clock positions, the white slides went in at ten and two o'clock.
9.Removed a surplus plastic piece from the new drum bearing (where the light comes through).
10.Inserted the new drum bearing, putting the bottom tabs in first, then pivoting it into place. I squeezed it into place to make sure it was tight.
11.Lifted up the drum and put the front panel back on.
12.Screwed the front panel back on, using the two screws.
13.Carefully put the top back on.
14.Screwed in the two screws inside the front door to fasten down the top.
That was it! I started up the dryer and it worked fine. No more squeaking.
About the only thing odd about the repair is why PartSelect sells each slide separately (i.e., I had to order 2 white slides and 2 gray slides). I can't imagine replacing just one, so why not package them in pairs, or maybe even all four in one package.
At any rate, the repair was easy, and a lot cheaper than having someone come out to fix it.
Read less
Was this instruction helpful to you?
Thank you for voting!