Magic Chef Dryer Parts

Start With Your Model Number

Need help finding your model number?
Find Parts Fast
Guaranteed Fit
Repair Videos
Fix.com search
Magic Chef Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular Magic Chef Dryer Parts

M Series New Style Coil Kit – Part Number: 279834
M Series New Style Coil Kit
$28.91
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX334310
Manufacturer Part Number
279834
This OEM kit comes with two ignition coils (one three-terminal boost/hold coil, and one two-terminal secondary coil). Usually only one of them burns out, but you should replace them as a set as both have to be operational for the gas valve to open. The primary purpose of the part is to open the gas valve and allow the gas to enter the burner. This is a safety mechanism to make sure that there is never an unsafe buildup of gas inside the appliance. You will find the coils attached to the dryer gas valve. This is not an uncommon repair; it can fail due to normal material fatigue over time. To test your current parts, watch the burner, and if the igniter glows for a while and then shuts off without the gas is igniting, it usually means one of these coils is bad.
Fixes these symptoms

Installation Instructions

Dennis from ALISO VIEJO, CA
Dryer ran but did not dry clothing.
Best site I have ever used for repairs. First a list of what parts were needed was provided right from the start, no guessing. I followed all of the video's provided for installation instructions and and that was it. Very easy to make repairs and almost rebuilt my dated dryer to like new condition. Appliance was in very good physical condition just needed new components to bring it back. Highly recommend this site to anyone who can turn a wrench. Read more...
Watch the install video
Dryer Idler Pulley Assembly – Part Number: WP691366
Dryer Idler Pulley Assembly
$16.35
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX11743765
Manufacturer Part Number
WP691366
The idler pulley is found in your dryer and provides tension to the belt in order to rotate the drum. If your clothes are taking a long time to dry, the machine is noisy while operating, or the dryer will not start or tumble, there may be an issue with the idler pulley assembly. To replace this part, you will need to lift the top and remove the front panel of the dryer. You will want to take note of how the drum belt is positioned so it can be put back in place once the new idler pulley is in place. While you have the appliance opened up and accessible, you may want to consider replacing the drum belt at this time.
Fixes these symptoms

Installation Instructions

carolyn from phila, PA
not spinning
follow the vidio Read more...
Watch the install video
Thermal Cut-Off Kit – Part Number: 279816
Thermal Cut-Off Kit
$48.21
In Stock
★★★★★
★★★★★
8 Reviews
Fix Number
FIX334299
Manufacturer Part Number
279816
This thermal cut-off kit is for a dryer and is sourced directly from the manufacturer. The thermal cut-off is a safety mechanism that is designed to trip if your dryer is at risk of overheating, to prevent further damage. It may need to be replaced if your washer is no longer heating properly. This is a one-time fuse, meaning if it trips, it needs to be replaced immediately. A common reason for this part to fail is if the heater housing is not receiving proper airflow, normally caused by an obstruction in the exhaust vent, a clogged lint screen, or a broken blower wheel. This kit includes 1 high-limit thermostat with a limit of 250 degrees Fahrenheit, 1 thermal cut-off fuse with a limit of 309 degrees Fahrenheit, jumper wires and new female spade terminals. These components are attached to the heater housing.
Fixes these symptoms
  • Heat stays on after drum has stopped
  • Not Heating
  • Too hot
  • See more...

Installation Instructions

Tim from Fargo, ND
Not getting hot enough, eventually no heat
I ordered the parts I thought may be the problem. If you watch any of the videos to help with a repair most of the video time is spent taking off and putting on the back panel. That being said once the panel was off it took me maybe 20 minutes to install the 4 parts I had ordered. Could have gone faster but also had 3 kids ages 2 and up to work around. This web site not only helps you trouble shoot but then gives discounts for the parts needed and helps with the repair through videos. Obviously the objective was to help customers from start to finish and I believe they achieved just that. Will use this site in the future and tell others about it as well. My instructions are to watch their video to do the repair. Don't rush or get anxious just focus on your task. My wife said the dryer works like new now. Read more...
Watch the install video
Dryer Thermal Fuse – Part Number: WP3392519
Dryer Thermal Fuse
$17.44
In Stock
★★★★★
★★★★★
16 Reviews
Fix Number
FIX11741460
Manufacturer Part Number
WP3392519
The dryer thermal fuse, also sometimes referred to as the thermal cut off or temperature fuse, is a 2 by 1/2-inch, white, plastic safety mechanism that halts the flow of electricity to the motor circuit when a dryer overheats. If the fuse is missing or broken, your dryer will not start. A thermal fuse fails when the exhaust temperature exceeds the fuse rating, that is when the temperature rises above the temperature that the fuse is intended to manage. This can be caused by the heating element shorting, a regulating thermostat or thermistor failure, or with a partially restricted exhaust vent. The fuse attaches to the blower wheel housing. It must be replaced when there is no longer continuity between the terminals. This is a one-time fuse, meaning it cannot be re-set. The replacement part features two 3/16-inch terminals. While performing this repair, we recommend checking to make sure all vents are cleared and vacuumed. This OEM part is sold individually.
Fixes these symptoms
  • Drum Not Spinning
  • Heat stays on after drum has stopped
  • Not Heating
  • See more...

Installation Instructions

gary from apex, NC
dryer not heating
Checked the heating element and found a break in the heating coil. Decided to change the thermal fuse and the the cycling thermostat because of the age of the dryer. Read more...
Watch the install video
Multi Rib Belt - 92-1/4" – Part Number: 341241
Multi Rib Belt - 92-1/4"
$15.26
In Stock
★★★★★
★★★★★
20 Reviews
Fix Number
FIX346995
Manufacturer Part Number
341241
This multi rib belt is an OEM replacement part for a dryer. It attaches to the drum, idler pulley, and motor pulley, and is responsible for spinning the drum. Over time, the belt can become frayed, brittle, and inflexible. If you can hear the motor running, but the drum does not turn, it is likely that the belt is broken. Other symptoms of a broken multi rib belt include unusual noises, failing to start, no heat, a burning smell, and an unresponsive touchpad. Depending on the model, you will find the belt by looking behind the front panel or under the main top of the dryer. This belt is 1/4-inches wide, has a length of 92-1/4-inches, and has four ridges and three groves on the belt. Each belt is sold separately.
Fixes these symptoms
  • Drum Not Spinning
  • Heat stays on after drum has stopped
  • Noisy
  • See more...

Installation Instructions

carolyn from phila, PA
not spinning
follow the vidio Read more...
Watch the install video
Igniter Kit – Part Number: 279311
Igniter Kit
$33.20
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX334180
Manufacturer Part Number
279311
This is a genuine OEM replacement igniter kit for your gas-heated clothes dryer. The silicon carbide igniter is used to light the gas that creates the heat in order to dry your clothes. If your dryer is not heating, takes a long time to dry clothes, or has low heat you may want to consider replacing your igniter. This kit can be used to replace both round and flat igniters, and comes with a 3-inch flat igniter, bracket, 4-inch wire lead, and the plug. Before beginning this repair, please ensure that the power and gas is disconnected from the range. As the igniter is located within the burner assembly, you will need a variety of tools to complete the installation. These tools include a putty knife, a small flat blade screwdriver, a 5/16 nut driver, and a 5/16 socket with a ratchet. This part should be handled with care, as the igniter is very fragile.
Fixes these symptoms

Installation Instructions

Joe from Red Bank, NJ
The coil kit was malfunctioning. Difficult to fully diagnosis as the problem.
The coil kit showed the correct numbers and it worked intermittently. However, when replaced everything worked OK. I also replaced the igniter, however, I do not believed it was a problem. However, I left in the new igniter. Read more...
Watch the install video
Rear Drum Support Roller Kit – Part Number: 349241T
Rear Drum Support Roller Kit
$18.54
In Stock
★★★★★
★★★★★
3 Reviews
Fix Number
FIX347627
Manufacturer Part Number
349241T
This is a rear drum support roller kit for your dryer. The 2 rollers come with 4 tri-rings, and 1 palnut. We recommend that you replace both rollers at once. This kit stabilizes the drum cylinder, while letting the drum rotate on the support rollers. If you are having problems with your appliance during tumble mode, or if it is too noisy, you will need this kit. To complete this repair you will need a putty knife, Philips screwdriver and a 5/16 nut driver.
Fixes these symptoms
  • Drum Not Spinning
  • Marks left on clothes
  • Noisy
  • See more...

Installation Instructions

Tyrik from KENNESAW, GA
The roller support wheels were worn down and needed replacing.
Step 1: removed power source.
Step 2: removed screws from lent catcher.
Step 3: removed top lid.
Step 4: removed front panel.
Step 5: removed drum.
Step 6: removed plastic washers.
Step 7: removed old wheels.
Step 8: installed new wheels.
Reversed steps to put everything back. Read more...
Dryer High Limit Thermostat – Part Number: WP3977767
Dryer High Limit Thermostat
$20.72
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX11742185
Manufacturer Part Number
WP3977767
This is a manufacturer-approved high-limit thermostat for your dryer. This part includes one high limit thermostat with a terminal extension arm. It is a safety mechanism that prevents your dryer from overheating. Once the temperature reaches 221 degrees Fahrenheit, this element will shut down power to the heating element until it decreases to 80 degrees Fahrenheit. If this part is faulty, your dryer may not heat. You will find this part located underneath the dryer vent behind the appliance. The terminal extension arm connects to the heater element terminal. The high limit thermostat can be tested with a multimeter. It should be tested while it is at room temperature, and will need to be replaced if the reading determines it is faulty.
Fixes these symptoms
  • Heat stays on after drum has stopped
  • Not Heating
  • Too hot
  • See more...

Installation Instructions

Tim from Fargo, ND
Not getting hot enough, eventually no heat
I ordered the parts I thought may be the problem. If you watch any of the videos to help with a repair most of the video time is spent taking off and putting on the back panel. That being said once the panel was off it took me maybe 20 minutes to install the 4 parts I had ordered. Could have gone faster but also had 3 kids ages 2 and up to work around. This web site not only helps you trouble shoot but then gives discounts for the parts needed and helps with the repair through videos. Obviously the objective was to help customers from start to finish and I believe they achieved just that. Will use this site in the future and tell others about it as well. My instructions are to watch their video to do the repair. Don't rush or get anxious just focus on your task. My wife said the dryer works like new now. Read more...
Watch the install video
Dryer Cycling Thermostat – Part Number: WP3387134
Dryer Cycling Thermostat
$27.28
In Stock
★★★★★
★★★★★
8 Reviews
Fix Number
FIX11741405
Manufacturer Part Number
WP3387134
This thermostat is an OEM replacement part for a dryer. It is sold individually. It measures approximately 2-inches by 1.5-inches, is black and silver, and constructed of plastic and metal material. You will find this part attached to the blower wheel housing. Cycling thermostats continually cycle the heating element off and on to maintain a constant inner temperature inside the dryer. This particular cycling thermostat will turn the heating element off once the temperature reaches 155F and cycles back on once the internal temperature drops by 25F. Do not forget to unplug the power to the dryer before you begin this repair. Keep in mind that you will need to pull the dryer out from the wall because this repair will need to be done from the back of the appliance with the back panel removed.
Fixes these symptoms
  • Heat stays on after drum has stopped
  • Not Heating
  • Timer Not Working
  • See more...

Installation Instructions

gary from apex, NC
dryer not heating
Checked the heating element and found a break in the heating coil. Decided to change the thermal fuse and the the cycling thermostat because of the age of the dryer. Read more...
Watch the install video
Door Catch Kit – Part Number: 279570
Door Catch Kit
$8.70
In Stock
★★★★★
★★★★★
11 Reviews
Fix Number
FIX334230
Manufacturer Part Number
279570
This kit includes two door strikes, and three door catches, to service doors that have one or two catches. The strike is mounted on the body of the dryer, while the catch is mounted on the dryer door. These two parts work together to keep the dryer door shut while in operation. If your appliances lid will not close, or it will not start, it may be time to replace the door catch. If this part is malfunctioning, it should be replaced immediately, as it is not safe to run a dryer with the door not properly closed. This kit also comes with a set of instructions to help with the repair.
Fixes these symptoms
  • Door Pops Open
  • Door won’t close
  • Lid or door won’t close
  • See more...

Installation Instructions

jeffrey from Brookhaven, PA
Dryer would run, but not heat
Needed it running quick, so no diagnostics. Ordered one of everything that could fix problem (plus a new door catch). Tipped it onto it's back & popped the bottom cover off. Element, thermal cutoff, thermistor, and fuse. were right in front and held by 2 screws each (don't drop them, don't ask). A little bit tight inside, but no big issue. vacuumed the inside, replaced everything (it was the Heating Element, by the way), slapped the cover on, and put it back in its spot. works like it was new. Yes, I unplugged it first. Remember! Safety Third! Read more...

Magic Chef Dryer Appliance Types

Related Magic Chef Dryer Parts

Popular Magic Chef Dryer Models

View More
+