Dryer Thermostats

★★★★★

★★★★★

15 Reviews

Fix Number

FIX11741460

Manufacturer Part Number

WP3392519

The dryer thermal fuse, also sometimes referred to as the thermal cut off or temperature fuse, is a 2 by 1/2-inch, white, plastic safety mechanism that halts the flow of electricity to the motor circuit when a dryer overheats. If the fuse is missing or broken, your dryer will not start. A thermal fuse fails when the exhaust temperature exceeds the fuse rating, that is when the temperature rises above the temperature that the fuse is intended to manage. This can be caused by the heating element shorting, a regulating thermostat or thermistor failure, or with a partially restricted exhaust vent. The fuse attaches to the blower wheel housing. It must be replaced when there is no longer continuity between the terminals. This is a one-time fuse, meaning it cannot be re-set. The replacement part features two 3/16-inch terminals. While performing this repair, we recommend checking to make sure all vents are cleared and vacuumed. This OEM part is sold individually.

★★★★★

★★★★★

8 Reviews

Fix Number

FIX11741405

Manufacturer Part Number

WP3387134

This thermostat is an OEM replacement part for a dryer. It is sold individually. It measures approximately 2-inches by 1.5-inches, is black and silver, and constructed of plastic and metal material. You will find this part attached to the blower wheel housing. Cycling thermostats continually cycle the heating element off and on to maintain a constant inner temperature inside the dryer. This particular cycling thermostat will turn the heating element off once the temperature reaches 155F and cycles back on once the internal temperature drops by 25F. Do not forget to unplug the power to the dryer before you begin this repair. Keep in mind that you will need to pull the dryer out from the wall because this repair will need to be done from the back of the appliance with the back panel removed.

★★★★★

★★★★★

8 Reviews

Fix Number

FIX334299

Manufacturer Part Number

279816

This thermal cut-off kit is for a dryer and is sourced directly from the manufacturer. The thermal cut-off is a safety mechanism that is designed to trip if your dryer is at risk of overheating, to prevent further damage. It may need to be replaced if your washer is no longer heating properly. This is a one-time fuse, meaning if it trips, it needs to be replaced immediately. A common reason for this part to fail is if the heater housing is not receiving proper airflow, normally caused by an obstruction in the exhaust vent, a clogged lint screen, or a broken blower wheel. This kit includes 1 high-limit thermostat with a limit of 250 degrees Fahrenheit, 1 thermal cut-off fuse with a limit of 309 degrees Fahrenheit, jumper wires and new female spade terminals. These components are attached to the heater housing.

★★★★★

★★★★★

1 Review

Fix Number

FIX11742185

Manufacturer Part Number

WP3977767

This is a manufacturer-approved high-limit thermostat for your dryer. This part includes one high limit thermostat with a terminal extension arm. It is a safety mechanism that prevents your dryer from overheating. Once the temperature reaches 221 degrees Fahrenheit, this element will shut down power to the heating element until it decreases to 80 degrees Fahrenheit. If this part is faulty, your dryer may not heat. You will find this part located underneath the dryer vent behind the appliance. The terminal extension arm connects to the heater element terminal. The high limit thermostat can be tested with a multimeter. It should be tested while it is at room temperature, and will need to be replaced if the reading determines it is faulty.

★★★★★

★★★★★

4 Reviews

Fix Number

FIX3530485

Manufacturer Part Number

6931EL3003D

If your dryer is not turning on, or not heating up, there could be an issue with your thermal fuse. This OEM fuse is designed to act as a high-limit thermostat, and will turn off the heating element in your dryer if the appliance overheats. It does this by cutting off power to the dryer. If the fuse has blown, it will need to be replaced as they cannot be reset. You can test the fuse with a multimeter, and should receive a reading of 0 ohms of resistance if the fuse is still good. A common reason for a dryer to overheat is if the air vents are blocked, as the hot air is contained in the dryer causing the fuse to blow. Be sure to keep your dryer filter and vents clean of lint and other debris to prevent this from happening.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX334278

Manufacturer Part Number

279769

This genuine OEM kit includes a high limit thermostat and a thermal cut-off fuse for your dryer. The thermostat has a limit of 250 degrees Fahrenheit, and the fuse has a limit of 360 degrees Fahrenheit. The purpose of these parts is to prevent your dryer from overheating. If your clothes are coming out of the dryer too hot, or there is no heat at all, it is likely that these parts will need to be replaced. To complete this repair, you will need a putty knife, quarter-inch nut driver, and a pair of pliers. Please be sure to disconnect the power supply to your dryer before beginning this repair. The thermostats are located on the element housing, and we find it easiest to remove the entire heating assembly from the dryer in order to replace these parts. Take note when removing the old thermostats, if there is any discoloration on the terminals then the wire ends may also need to be replaced.

Fix Number

FIX334387

Manufacturer Part Number

279973

This thermal cut-off kit includes a genuine OEM replacement high limit thermostat and a fuse. The thermostat is a safety device used to prevent the dryer from overheating, and the fuse serves as a backup. If the temperature in your dryer gets above the thermostat, the fuse will blow. Once the fuse has tripped, it will need to be replaced. If your dryer will not start, gets too hot, shuts off too soon, or there is no heat, you may need to replace these components. Please be sure to disconnect the power supply to your dryer before beginning this repair, as you will be working with electrical components.

Fix Number

FIX11772030

Manufacturer Part Number

WE04X25201

Fix Number

FIX446428

Manufacturer Part Number

3204267

This high limit thermostat has a limit of 260 degrees Fahrenheit. Meaning that it will cut out when the internal dryer temperature reaches 260. This thermostat cuts back in when the temperature drops by 70 degrees Fahrenheit.

Fix Number

FIX11759043

Manufacturer Part Number

WE04X25194