Norge Dryer Parts

Fix Number: FIX334310
Manufacturer Part Number: 279834

This OEM kit comes with two ignition coils (one three-terminal boost/hold coil, and one two-terminal secondary coil). Usually only one of them burns out, but you should replace them as a set as both have to be operational for the gas valve to open. The primary purpose of the part is to open the gas valve and allow the gas to enter the burner. This is a safety mechanism to make sure that there is never an unsafe buildup of gas inside the appliance. You will find the coils attached to the dryer gas valve. This is not an uncommon repair; it can fail due to normal material fatigue over time. To test your current parts, watch the burner, and if the igniter glows for a while and then shuts off without the gas is igniting, it usually means one of these coils is bad.

Fixes these symptoms

Noisy
Not Heating
See more...

Installation Instructions

Dennis from ALISO VIEJO, CA

Dryer ran but did not dry clothing.

Best site I have ever used for repairs. First a list of what parts were needed was provided right from the start, no guessing. I followed all of the video's provided for installation instructions and and that was it. Very easy to make repairs and almost rebuilt my dated dryer to like new condition. Appliance was in very good physical condition just needed new components to bring it back. Highly recommend this site to anyone who can turn a wrench. Read more...

Retaining Ring

$7.87

Fix Number: FIX11746909
Manufacturer Part Number: WP9703438

Sometimes referred to as a retaining clip, the retaining ring is used to hold the drum support roller onto the shaft in your dryer. The clip may need to be replaced if you find that your dryer is noisy while tumbling or will not tumble at all. The retaining clip can also be used with stand mixers, to hold the pinion gear to the agitator shaft. This genuine OEM part is made entirely out of metal and measures approximately half an inch in diameter.

Fixes these symptoms

Noisy
See more...

Installation Instructions

Brian from Novi, MI

Squeaking noises while running dryer

Followed the Video Directions from website. All went as planed. The dryer is running like new now. Read more...

Dryer Radiant Flame Sensor

$47.87

Fix Number: FIX11741429
Manufacturer Part Number: WP338906

This genuine OEM part is a radiant flame sensor for your gas dryer. It is used to determine when the temperature of the igniter is hot enough to ignite the gas. Once the igniter is hot enough, it allows the valve to open to release the gas. This acts as a safety mechanism which prevents dangerous levels of gas from building up. If your dryer will not start, is not producing enough heat, not heating up at all, is taking too long to dry laundry, or is shutting off too soon, you may need to replace the radiant flame sensor. Please be sure to disconnect the power and gas supply to your dryer before beginning this repair.

Fixes these symptoms

Not Heating
See more...

Installation Instructions

William from Corsicana, TX

Oor dryer would not get hot.

I opened the bottom section and watched as the igniter got red hot as it should but the gas valve did not open. I wired around the sensor and the gas valve opened and the fuel ignited. VERY IMPORTANT: DO NOT RUN YOUR DRYER IN THIS STATE: IT WILL BLOW UP!! I did a VERY short test, then ordered the new sensor. Just one screw holds the sensor (as shown in the Parts video). One screw out, new sensor, one screw in and our dryer is back in full and proper running order. Read more...

High Limit Kit

$32.98

3 Reviews

Fix Number: FIX2162282
Manufacturer Part Number: LA-1053

This kit comes with three separate thermal fuses and is usually used with clothes dryers that have a fan mounted on the motor shaft. Included within this kit is the high limit (Limit: 258) the gas high limit (Limit: 240) and the gas and electric high limit thermostat (Limit: 300).

Fixes these symptoms

Too hot
Will Not Start
Won’t Start
See more...

Installation Instructions

Michael from Statesville, NC

dryer quit working during operation and failed to restart

resistor is located on top back of dryer, so just removed metal plate on back with screwdriver. other parts are located above drum, and top of dryer is hinged, so lifted top of dryer by taking small screwdriver and wedged between front and top of dryer enough to get fingers underneath top and lifted. very simple. door switch and high limit switch could be viewed and removed at this point. Read more...

Door Catch Kit

$32.31

2 Reviews

Fix Number: FIX2162263
Manufacturer Part Number: LA-1003

This kit comes in two pieces: the catch and the clip.

Fixes these symptoms

Door Pops Open
Door won’t close
See more...

Installation Instructions

James from Joshua, TX

Dryer plastic door catch was broke on dryer

I watched several videos on how to replace the latch, but my latch was broken on one side so I took a pair of pliers and a screwdriver and pried the old one out. Push the new one in, then replaced the male catch on the door. i didn't tighten the screw holding the male latch because they use it to allign the latch with the catch. Read more...

Blower Wheel

$59.10

2 Reviews

Fix Number: FIX16221211
Manufacturer Part Number: W11497304

This wheel has a deep D-shaped shaft receptacle. The spring clamp is not included with this part.

Fixes these symptoms

Noisy
See more...

Installation Instructions

John from Dallastown, PA

replaced blower wheel and belt

taking it apart was easy the hard part was removing excess plastic from D shaped hole in wheel. There is so much plastic in center hole that it will not seat on shaft. I had to use a drill and dove tail file to do this project. F.Y.I. this was the second wheel the first i broke when it was half way on the shaft tap lightly my friend. Read more...

Heating Element Kit - 240V 4750W

$78.81

Fix Number: FIX2162280
Manufacturer Part Number: LA-1044

Fixes these symptoms

Not Heating
Too hot
See more...

Installation Instructions

CRAIG from DAPHNE, AL

would not start

checked continuity on the thermal fuse it was bad ordered new fuse and heat element (dryer is over 10 years old time for new element) took out drum and behind it was heat assy, replaced fuse and element put back together and hit start button worked great Read more...

Blower Wheel Clamp

$13.60

Fix Number: FIX11740752
Manufacturer Part Number: WP312967

This blower wheel clamp is less than an inch long and is used for some clothes dryers to hold the blower wheel firmly in place. This green clamp is made of metal.

Fixes these symptoms

Noisy
See more...

Installation Instructions

Harold from BEAVER, PA

Dryer was making loud noises.

Basically I did it as shown in the video.

I want to note that there was no blower wheel clamp on the broken blower wheel. This was the third time I have replaced that blower wheel, and lack of a clamp may have contributed to premature failure. Luckily, this time I watched the video before ordering parts so I knew about the clamp. Don't forget the clamp., Read more...

Lint Filter

$58.48