Norge Parts

★★★★★

★★★★★

2 Reviews

Fix Number

FIX884734

Manufacturer Part Number

8009

This is a genuine OEM 40-Watt replacement light bulb that is compatible with various types of appliances. It has a frosted glass bulb with a standard metal socket base, making it easy to screw and unscrew by hand to replace. It is designed to tolerate extreme temperatures, which is why it is commonly used to light the inside of refrigerators and ovens. Depending on the appliance and location of the bulb, disconnecting the power is recommended. This bulb is sold individually.

★★★★★

★★★★★

4 Reviews

Fix Number

FIX11750108

Manufacturer Part Number

WPW10196406

This chrome drip bowl is an OEM approved replacement part designed for use with various models of electric ranges and cooktops. This drip bowl fits under 6-inch burner elements and has a diameter of approximately 8 inches. It sits under the burner, keeping any drips and spill contained. It is common for this part to become discolored, corroded, or otherwise damaged with time, and will need to be replaced. Each drip bowl is sold individually, so this is a good time to check the other drip bowls on the appliance in case you would like to replace those as well (sold separately). No tools are required for installation, simply line up the hole on the bowl with the terminal block and drop it into place. By routinely cleaning this part, it will help to prolong its life.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX2366565

Manufacturer Part Number

W10196406RW

The drip bowl is used for electric ranges or cooktops with the coiled style burners, to catch any drips, spills, or crumbs that may occur while cooking. If your bowls have become discolored, corroded, difficult to clean, or otherwise damaged it may be time to replace them. This repair is easy and does not require any tools to complete the job. Ensure that all burners are turned off and cool to the touch before starting. First you need to lift up and disconnect the burner from the socket. While you have the burner out, it is a good time to check it for any signs of damage. Look at the terminals for any signs of arcing or burning. If you notice this, you will want to replace both the element and the receptacle it plugs into. Remove the old drip bowl by pulling it out. Then insert the new one by lining up the small hole on the side with the element block. Ensure that it is siting flat and then plug the element back into the socket. Please note that the manufacturer has substituted this part, and it no longer has a solid bottom. It is not recommended to cover the hole with products like aluminum foil, as it can trap heat or melt, becoming a fire hazard. As it is an OEM part, it ensures it will fit your model. The drip bowls are sold individually, chrome in color and about 8 inches in diameter, made to fit under a 6 inch burner element.

Fix Number

FIX11746909

Manufacturer Part Number

WP9703438

Sometimes referred to as a retaining clip, the retaining ring is used to hold the drum support roller onto the shaft in your dryer. The clip may need to be replaced if you find that your dryer is noisy while tumbling or will not tumble at all. The retaining clip can also be used with stand mixers, to hold the pinion gear to the agitator shaft. This genuine OEM part is made entirely out of metal and measures approximately half an inch in diameter.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX334310

Manufacturer Part Number

279834

This OEM kit comes with two ignition coils (one three-terminal boost/hold coil, and one two-terminal secondary coil). Usually only one of them burns out, but you should replace them as a set as both have to be operational for the gas valve to open. The primary purpose of the part is to open the gas valve and allow the gas to enter the burner. This is a safety mechanism to make sure that there is never an unsafe buildup of gas inside the appliance. You will find the coils attached to the dryer gas valve. This is not an uncommon repair; it can fail due to normal material fatigue over time. To test your current parts, watch the burner, and if the igniter glows for a while and then shuts off without the gas is igniting, it usually means one of these coils is bad.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX2121513

Manufacturer Part Number

D7824706Q

If your freezer has stopped making ice cubes, it may be time to replace your ice maker. Normal wear and tear, or accidental damage may be the cause of this. This model includes the control device and ice mold, which are made of plastic and metal, and measure approximately 11 inches long by 5 inches wide. Please note that this kit does not include the cover, ice level arm, or the wire harness. These parts can be ordered separately, or you can use the existing parts from the original ice maker. This Replacement Ice Maker is a genuine OEM part and is also known as an Ice Maker Assembly or a Refrigerator Ice Maker. Installation will require a quarter inch nut driver, and make sure that you disconnect your power and water supply before beginning this repair. Once the new part is in place, your fridge will begin making ice again within a few hours.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX11757023

Manufacturer Part Number

WPW10662129

The capacitor, also known as a run capacitor, is a component in your fridge that allows the compressor to cycle on and off to maintain a constant temperature. If your fridge and freezer are too warm it may be necessary to replace the capacitor. Other symptoms include an unusually noisy and overheated compressor. You can check the capacitor for continuity using a multimeter. This is a genuine OEM replacement part made of black plastic that measures 1 inch by 1.5 inches. When replacing this part, be sure to check the electrical contacts on the old capacitor. If they are corroded or burnt, you will need to replace the overload relay assembly as well. Be sure to disconnect the power supply to your refrigerator before beginning this repair.

★★★★★

★★★★★

20 Reviews

Fix Number

FIX346995

Manufacturer Part Number

341241

This multi rib belt is an OEM replacement part for a dryer. It attaches to the drum, idler pulley, and motor pulley, and is responsible for spinning the drum. Over time, the belt can become frayed, brittle, and inflexible. If you can hear the motor running, but the drum does not turn, it is likely that the belt is broken. Other symptoms of a broken multi rib belt include unusual noises, failing to start, no heat, a burning smell, and an unresponsive touchpad. Depending on the model, you will find the belt by looking behind the front panel or under the main top of the dryer. This belt is 1/4-inches wide, has a length of 92-1/4-inches, and has four ridges and three groves on the belt. Each belt is sold separately.

Fix Number

FIX1960673

Manufacturer Part Number

W10135699

This three count package of Affresh Washing Machine Cleaner helps remove odor causing residue from inside the washer, each slow dissolving tablet works throughout the wash cycle and is suitable for all washer brands, including high efficiency machines, place one tablet directly in the empty wash basket, not the dispenser, and run the Clean Washer cycle, or use a normal cycle with hot water, the tablets are septic safe and should be used monthly or every 30 wash cycles for best results

★★★★★

★★★★★

1 Review

Fix Number

FIX11750107

Manufacturer Part Number

WPW10196405

This chrome drip bowl is an OEM approved replacement part sourced directly from the manufacturer. Drip bowls are a part for your cooktop, positioned underneath the burner to catch spills. This drip bowl fits under 8-inch burner elements and has a diameter of approximately 10-inches. It is common for the manufacturer to switch up designs, so it may not match your current part, however searching using the correct model number will ensure proper fit and function. Drips bowls are prone to wear and tear and can be a fire hazard if not replaced when needed. It is also a quick, easy, and cheap way to give your appliance a fresh new look. Each drip bowl is sold individually, so if you are interested in replacing your other drips bowls, they need to be ordered separately. This is also an opportune time to inspect the terminals for corrosion or damage, and the condition of the burner. No tools are required for installation, simply line up the hole on the bowl with the terminal block and drop it into place. Give your new drip bowl a regular cleaning with warm water and soap to help it last as long as possible.