Hoover Dryer Parts
Start With Your Model Number
Find Parts Fast
Guaranteed Fit
Repair Videos
Need help finding your model number?

Popular Hoover Dryer Parts
$17.19
In Stock
Multi Rib Belt - 92-1/4"
Fix Number FIX346995
Manufacturer Part Number 341241
This multi rib belt is an OEM replacement part for a dryer. It attaches to the drum, idler pulley, and motor pulley, and is responsible for spinning the drum. Over time, the belt can become frayed, brittle, and inflexible. If you can hear the motor running, but the drum does not turn, it is likely that the belt is broken. Other symptoms of a broken multi rib belt include unusual noises, failing to start, no heat, a burning smell, and an unresponsive touchpad. Depending on the model, you will find the belt by looking behind the front panel or under the main top of the dryer. This belt is 1/4-inches wide, has a length of 92-1/4-inches, and has four ridges and three groves on the belt. Each belt is sold separately.
Fixes these symptoms
- Drum Not Spinning
- Heat stays on after drum has stopped
- Noisy
- See more...
$32.34
In Stock
Door Catch Kit
Fix Number FIX2162263
Manufacturer Part Number LA-1003
This kit comes in two pieces: the catch and the clip.
Fixes these symptoms
- Door won’t close
- See more...
Installation Instructions
James from Joshua, TX
Dryer plastic door catch was broke on dryer
I watched several videos on how to replace the latch, but my latch was broken on one side so I took a pair of pliers and a screwdriver and pried the old one out. Push the new one in, then replaced the male catch on the door. i didn't tighten the screw holding the male latch because they use it to allign the latch with the catch.
Read more...
M Series New Style Coil Kit
Fix Number FIX334310
Manufacturer Part Number 279834
This OEM kit comes with two ignition coils (one three-terminal boost/hold coil, and one two-terminal secondary coil). Usually only one of them burns out, but you should replace them as a set as both have to be operational for the gas valve to open. The primary purpose of the part is to open the gas valve and allow the gas to enter the burner. This is a safety mechanism to make sure that there is never an unsafe buildup of gas inside the appliance. You will find the coils attached to the dryer gas valve. This is not an uncommon repair; it can fail due to normal material fatigue over time. To test your current parts, watch the burner, and if the igniter glows for a while and then shuts off without the gas is igniting, it usually means one of these coils is bad.
Fixes these symptoms
- Noisy
- Not Heating
- See more...
Installation Instructions
Dennis from ALISO VIEJO, CA
Dryer ran but did not dry clothing.
Best site I have ever used for repairs. First a list of what parts were needed was provided right from the start, no guessing. I followed all of the video's provided for installation instructions and and that was it. Very easy to make repairs and almost rebuilt my dated dryer to like new condition. Appliance was in very good physical condition just needed new components to bring it back. Highly recommend this site to anyone who can turn a wrench.
Read more...
$58.64
In Stock
Lint Filter
Fix Number FIX11742807
Manufacturer Part Number WP53-0918
This lint filter screen has two side guides on either either of the screen. One measures 3/8 of an inch wide, while the other measures 5/8 of an inch wide
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Debi from GROTTOES, VA
$33.01
In Stock
High Limit Kit
Fix Number FIX2162282
Manufacturer Part Number LA-1053
This kit comes with three separate thermal fuses and is usually used with clothes dryers that have a fan mounted on the motor shaft. Included within this kit is the high limit (Limit: 258) the gas high limit (Limit: 240) and the gas and electric high limit thermostat (Limit: 300).
Fixes these symptoms
- Too hot
- Will Not Start
- See more...
Installation Instructions
Michael from Statesville, NC
dryer quit working during operation and failed to restart
resistor is located on top back of dryer, so just removed metal plate on back with screwdriver. other parts are located above drum, and top of dryer is hinged, so lifted top of dryer by taking small screwdriver and wedged between front and top of dryer enough to get fingers underneath top and lifted. very simple. door switch and high limit switch could be viewed and removed at this point.
Read more...
$47.91
In Stock
Dryer Radiant Flame Sensor
Fix Number FIX11741429
Manufacturer Part Number WP338906
This genuine OEM part is a radiant flame sensor for your gas dryer. It is used to determine when the temperature of the igniter is hot enough to ignite the gas. Once the igniter is hot enough, it allows the valve to open to release the gas. This acts as a safety mechanism which prevents dangerous levels of gas from building up. If your dryer will not start, is not producing enough heat, not heating up at all, is taking too long to dry laundry, or is shutting off too soon, you may need to replace the radiant flame sensor. Please be sure to disconnect the power and gas supply to your dryer before beginning this repair.
Fixes these symptoms
- Not Heating
- See more...
Installation Instructions
Donald from Ottawa, IL
no heat
Cost was $114.00 to replace all parts , It took longer to take apart & test everything than it did to do the repair ! I tested all parts twice , everything would test fine , I put it all back together and the dryer worked for 5 minutes , did that twice and decided to order all the parts an be done with it . Ordered the parts , that showed up at my door in 2 days !!! Turned OFF gas , took off vent hose , took back off with 8 screws , popped up top in the front , took 2 screws off the top in the back removing the brackets , Inside the front under the top removed 2 screws holding on the front , lifted the front and removed . All parts only have 1 or 2 screws holding them in place , removed 1 part at a time , removing and replacing 1 wire from old part to the new part so I did not mix up the wires , replace the part and go to the next part . It was pretty self explanatory replacing the parts , It took 20 minutes to take apart , replace the parts and put back together so my loving wife could do laundry again. You don't realize what a inconvenience it is to go without a dryer for 3 days when you have had one for 37 yrs ..... THANK YOU , 3 days can seem like forever when someone is not happy , but it was much much better than waiting 7 to 10 days for the wrong parts from somewhere else . You have the BEST parts website that I have EVER used !!! THANK YOU AGAIN , Donald
Read more...
$39.87
In Stock
Drum Felt Seal
Fix Number FIX11740735
Manufacturer Part Number WP31001747
Depending upon your model, this seal can be used on either the front or rear drum. The hi-temp adhesive is sold separately.
Fixes these symptoms
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
JOHN from Lakewood, CO
Dryer leaving rust streaks on white laundry
The video was exactly right for installing the upper drum glide. Getting the front off of the machine took less than 5 minutes. The old glide and felt peeled off easily. I used a putty knife and a file rasp to remove the old glue. Used denatured alcohol to wipe away any residual dust and pieces of glue. Applied the glue in two parallel lines where the new glides and pad install. Waited about a minute for the glue to get tacky, then placed new part on the upper door opening. To hold it down, I used an adjustable 1.5 inch wide nylon tie down strap around the entire circumference of the door opening and ratcheted it down tight for overnight. Next morning took off the strap and repair was tight. If you are going to replace the upper glide, go ahead and do the lower seal as well. If the upper is worn out, the lower will be worn out of shape and won't seal right with a new one only on the top. Repair time 30 minutes from open to close, with 12 hours glue drying time in between.
Read more...
$13.61
In Stock
Blower Wheel Clamp
I want to note that there was no blower wheel clamp on the broken blower wheel. This was the third time I have replaced that blower wheel, and lack of a clamp may have contributed to premature failure. Luckily, this time I watched the video before ordering parts so I knew about the clamp. Don't forget the clamp., Read more...
Fix Number FIX11740752
Manufacturer Part Number WP312967
This blower wheel clamp is less than an inch long and is used for some clothes dryers to hold the blower wheel firmly in place. This green clamp is made of metal.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Harold from BEAVER, PA
Dryer was making loud noises.
Basically I did it as shown in the video. I want to note that there was no blower wheel clamp on the broken blower wheel. This was the third time I have replaced that blower wheel, and lack of a clamp may have contributed to premature failure. Luckily, this time I watched the video before ordering parts so I knew about the clamp. Don't forget the clamp., Read more...
$78.88
In Stock
Heating Element Kit - 240V 4750W
Fix Number FIX2162280
Manufacturer Part Number LA-1044
Fixes these symptoms
- Not Heating
- Too hot
- See more...
Installation Instructions
CRAIG from DAPHNE, AL
would not start
checked continuity on the thermal fuse it was bad ordered new fuse and heat element (dryer is over 10 years old time for new element) took out drum and behind it was heat assy, replaced fuse and element put back together and hit start button worked great
Read more...