Models > LDGH200AGV

LDGH200AGV Hoover Dryer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for LDGH200AGV

Viewing 7 of 7
Keep searches simple, eg. "belt" or "pump".
This multi rib belt is an OEM replacement part for a dryer. It attaches to the drum, idler pulley, and motor pulley, and is responsible for spinning the drum. Over time, the belt can become frayed, br...
In Stock
This OEM kit comes with two ignition coils (one three-terminal boost/hold coil, and one two-terminal secondary coil). Usually only one of them burns out, but you should replace them as a set as both h...
In Stock
This lint filter screen has two side guides on either either of the screen. One measures 3/8 of an inch wide, while the other measures 5/8 of an inch wide
In Stock
This kit comes with three separate thermal fuses and is usually used with clothes dryers that have a fan mounted on the motor shaft. Included within this kit is the high limit (Limit: 258) the gas hig...
In Stock
This genuine OEM part is a radiant flame sensor for your gas dryer. It is used to determine when the temperature of the igniter is hot enough to ignite the gas. Once the igniter is hot enough, it allo...
In Stock
This kit comes in two pieces: the catch and the clip.
In Stock
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
This blower wheel clamp is less than an inch long and is used for some clothes dryers to hold the blower wheel firmly in place. This green clamp is made of metal.
In Stock
Included in this rear drum support roller kit are 4 screws, 1 spacers, 2 washers, 2 retaining rings, 2 rear rollers, and 2 cylinder support shafts. *** Note: Per manufacturer this kit has been upd...
No Longer Available
$7.67
This screw is sold individually.
In Stock
$86.53
If this part appears to be too wide for your particular appliance, per the manufacturer, all you have to do is pull it apart.
In Stock
This blower wheel is suitable for some clothes dryers of the 10 and earlier series. Manufactured to fit a 1/2 inch motor shaft, this blower wheel is 3-1/8 inches deep. The diameter of the wheel is 7-1...
In Stock

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Problems and Symptoms for LDGH200AGV

Viewing 11 of 11
Noisy
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Drum Not Spinning
Fixed by these parts
Fixing
How to fix it
Door won’t close
Fixed by these parts
Fixing
How to fix it
Not Heating
Fixed by these parts
Fixing Fixing
How to fix it
Too hot
Fixed by these parts
Fixing Fixing
How to fix it
Heat stays on after drum has stopped
Fixed by these parts
Fixing
How to fix it
Won’t Start
Fixed by these parts
Fixing Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing
How to fix it
Marks left on clothes
Fixed by these parts
Fixing
How to fix it
Will not agitate
Fixed by these parts
Fixing
How to fix it
Touchpad does not respond
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jane from Grand Forks, ND
Parts Used:
WP53-0918
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
lint filter broke
I pulled out the broken lint filter and put the new one back in, real easy. I am so happy with the prompt delivery I got from PartsSelect.com. I ordered on a Monday and and it was delivered on a Wednesday
482 of 494 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Stan from Riverside, CA
Parts Used:
WP53-0918, WP31001556, 341241
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
No Heat
Lift the top. Remove (2) screws holding the front of the dryer in place. Lift the front off the 2 retaining clips on the bottom of the dryer. The hardest part of the install was removing and replacing the igniter. A couple of helping hands from the girlfriend to hold the parts in place while I replaced the two screws was very helpfull . Installing the multi rib belt was also very easy with the help of a second pair of arms to reach under the drum to thread the belt onto the tensioner. The lint filter, of coarse was just a matter of throwing the old cracked one away and replacing w/ the new.
388 of 404 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from Haverhill, NH
Parts Used:
279834
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set
Dryer ran but would not heat
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are located on top of the gas valve. I borrowed my neighbor"s ohm meter and touched the two probes on the coils terminals to check for continuity and found that one of the coils read zero. I then took both of the coils out by removing two screws and tested each coil again. One coil read 500-850 and the other read zero. This meant that it was no good so I called for the part and received it in three days. I reassembled the parts and turned the dryer on and it fired up after a few seconds. It works as good as new. The part plus shipping was less than $30. My repairman would have charged me $150-$200. While the dryer was apart I gave it a good cleaning with a vacuum and a toothbrush in delicate areas. I also removed and cleaned the lint trap housing by removing two nuts. I didn't know much about gas dryers, but thanks to PartSelect I easily fixed it myself.
404 of 457 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!