Craftsman Parts

Craftsman Appliance Parts
Shop By Appliance Type

Popular Craftsman Parts

$16.99
In Stock
Tire Sealant
Fix Number FIX9875402
Manufacturer Part Number 100032R
$26.33
On Order
Wheel and tire assembly (Front Drive Wheels)
★★★★★
★★★★★
3 Reviews
Fix Number FIX11971248
Manufacturer Part Number 583719501
This is a genuine OEM sourced replacement part is used with walk behind lawn mowers. This is the drive wheel which has plastic gears on the inside. It is designed to be driven by a pinion gear which is sold separately. If the wheel is broken or damaged it should be replaced to ensure smooth ride and consistent cut of the grass. Includes one (1) plastic wheel.
$2.99
In Stock
Bow Tie Cotter Pin
Fix Number FIX9096195
Manufacturer Part Number 714-04040
This bow tie cotter pin fits snow blowers, as well as other gardening tools. The pin helps secure the auger to the shaft on a snow blower. Due to constant wear, this is a commonly replaced part. Tip: Extra pins are recommended. *Please note: this part is sold individually. For installation instructions, refer to the diagram provided by the manufacturer.
$8.37
Special Order
Primer Bulb Replacement
★★★★★
★★★★★
2 Reviews
Fix Number FIX9970593
Manufacturer Part Number 530071835
This part includes one primer bulb and two screws. These OEM parts are designed for gas chainsaws. The purge bulb is prone to cracking and breaking over time due to its constant contact with fuel. For this repair, start by removing the broken primer bulb from the unit, disconnect fuel lines and short the fuel line from the carburetor and long fuel line from the fuel tank. Next, connect the fuel lines to the new primer bulb and fit the fuel lines onto the fittings. Install the new primer bulb and secure it with the two screws.
$2.99
In Stock
Fuel Line Clamp
Fix Number FIX8938782
Manufacturer Part Number 26460
This and an authentic OEM replacement part sourced directly from the manufacturer. Fuel line clamps are used in small engines such as snow blowers, lawn mowers, tillers, and lawn tractors. Fuel line clamps are in place to ensure the fuel line is securely attached to the carburetor. It is important that your fuel line clamps are functioning properly; having a secure fuel line prevents fuel leaks in your engine. This part is made of metal. You will require pliers to install and secure tube clips.
$60.79
In Stock
Air Compressor Kit
★★★★★
★★★★★
4 Reviews
Fix Number FIX10048100
Manufacturer Part Number K-0650
This kit is an OEM part direct from Craftsman for air compressors. This kit consists of the parts for building a piston cylinder in the compressor. It is recommended that you release air and unplug the air compressor before you install this kit. You will need a wrench set to replace this part. This kit includes two o-rings, piston ring clamp screw and the cylinder tube. This kit is made of metal and rubber components.
Fixes these symptoms
$2.99
In Stock
Shear Pin, .25
Fix Number FIX9110822
Manufacturer Part Number 738-04124A
Designed for use in MTD, Yard Machine, Troy-Bilt, Yard-Man, and Craftsman machines, this OEM approved Shear Pin fits a variety of models. For full compatibility, please see the "Model Cross Reference List" below. This is a shear pin for your lawn and garden equipment, most commonly your snow blower. It is designed to snap if your auger gets jammed or clogged, to protect your snow blower from further damage. Because this part is meant to snap at a certain point of pressure, it is a commonly replaced part in snow blowers. Consequently, we recommend keeping a spare on hand. This Shear Pin is approximately 1.75" long, and is sold individually.
$4.64
In Stock
O-ring Kit
Fix Number FIX10042509
Manufacturer Part Number ACG-45
$8.86
In Stock
Fan
Fix Number FIX10042312
Manufacturer Part Number AC-0108
Installation Instructions
Steven from Darlington, SC
Air compressor was over heating and wouldn't restart after the first shut off.
Remove 1 Torx screw on end where air feeds into tank itself. Remove 2 Torx screws on other end. Pry cover apart. There are tabs that hold cover together. Remove screw that holds fan on. (my fan had dry rotted and had fallen off) Move shaft to lowest position and turn fan where hole is at the bottom. Slide onto shaft and replace bolt. Spin fan by hand to make sure it will rotate without going outside of where the cover will be when it is replaced. Put back cover on and replace the single screw. Snap front cover on and replace last 2 screws. You should be done. Plug up compressor and make sure it works correctly. Read more...
$52.55
In Stock
Valve Plate Assembly
★★★★★
★★★★★
1 Review
Fix Number FIX10054520
Manufacturer Part Number Z-AC-0032

Appliance Type

Popular Craftsman Models