OEM Craftsman Grinder Parts & Accessories

Wrench

$16.77

Fix Number: FIX10172231
Manufacturer Part Number: 401680-00

This wrench is an OEM direct from Craftsman for angle grinders. This part helps the motor shaft stay in place when the user pulls out or replaces the grinder disc. It is recommended to review your models diagram to verify the parts compatibility. This part is made of metal and sold individually.

Terminal

$6.51

Fix Number: FIX10173813
Manufacturer Part Number: 464228-00

This is a terminal for your power tools. The terminal attaches to the cord of your machine, and then to the electrical connection on the tool. Through this connection, the electricity travels from the wall, through the terminal, and into your machine. The most common reason for needing to replace this part, is if your machine is plugged in but not turning on.

Installation Instructions

John from SPRINGVILLE, CA

Old worn cord shorting out.

Remove the four screws and carefully separate the casing at the trigger handle. Disconnect the terminals by lifting the switch slightly, just enough to remove the inside terminal. Needle nose pliers will make it easier to remove the terminals. Slip the cord protector over the new cord. Cut the two new wires to the proper length. I measured the old connectors for proper fit. Strip a half inch off the insulation, carefully crimp and solder the wires to each terminal, reconnect the terminals, reposition the cord protector, align and snap the casing back together, and replace the four screws. Plug it in and test for proper operation. Read more...

Watch the install video

Spring

$9.17

Fix Number: FIX10179449
Manufacturer Part Number: 562210-00

This item is an authentic DeWalt replacement part that has been sourced from the original manufacturer to be used with angle grinders and masonry saws. In grinders, the metal spring is used to provide compression for the spindle lock pin. In masonry saws, the spring provides a similar function for the depth adjustment lever lock pin. This item is sold as an individual replacement part.

Wrench

$6.51

Fix Number: FIX10180699
Manufacturer Part Number: 596440-00

This replacement wrench is a genuine OEM approved part that is used with Dewalt, Black and Decker and Porter Cable agnle grinders. It is used to tighten or remove the outer flange which secures the grinding wheel. Please note this durable metal wrench is sold individually.

Carbon Brush

$6.51

★★★★★

1 Review

Fix Number: FIX10186156
Manufacturer Part Number: 949646-01

This is a Genuine Manufacturer Sourced replacement part used on Dewalt Grinders. This is a Carbon Brush with Lead Wire attached which is Sold Individually. Please note Brush Holder and Spring are Sold Separately. Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. It is recommended to replace both brushes at the same time. You would need a Screwdriver and Pliers to complete this job.

Ring, Retaining

$6.51

Fix Number: FIX10173387
Manufacturer Part Number: 444793-00

This is an authentic DeWALT and Black & Decker replacement part that is sourced from the original manufacturer for use with saws, grinders, jointers, nibblers, plate joiners, polishers, routers, sanders, and shears. The retaining ring attaches to the ball bearing and is made of metal. When replacing this item an allen wrench and a screwdriver might be required during the installation process. It will need to be replaced if it becomes bent or broken. This part is available as an individual replacement.

Inner Flange

$6.51

Fix Number: FIX10176006
Manufacturer Part Number: 5140005-34

This is an original replacement part manufactured for use with angle grinders. The special metal flange sits above the grinding wheel, and provides space between the wheel and guard. This inner flange is sold individually.

Watch the install video

330003-60

$6.51

Fix Number: FIX10169630
Manufacturer Part Number: 330003-60

This is a bearing, and it is used in various power tools. It is meant to reduce tension between the moving parts within the tool. This bearing has a 1 inch outer diameter, less than 1/4-inch inner diameter, and green walls.

Watch the install video

Electric Drill Cord Protector

$9.74

Fix Number: FIX10169655
Manufacturer Part Number: 330005-01

This is a cord protector, but it is also called a strain relief, and it is used with multiple power tools. This part is made of firm rubber to protect the cords from being pulled out or exposed, which would be a safety hazard. Over time the strain relief can develop cracks and break into pieces. This part is black and 4 inches long. The smallest end has a diameter of 0.5 inches. When completing this repair tuck in all wires to avoid pinching.

Installation Instructions

John from SPRINGVILLE, CA

Old worn cord shorting out.

Remove the four screws and carefully separate the casing at the trigger handle. Disconnect the terminals by lifting the switch slightly, just enough to remove the inside terminal. Needle nose pliers will make it easier to remove the terminals. Slip the cord protector over the new cord. Cut the two new wires to the proper length. I measured the old connectors for proper fit. Strip a half inch off the insulation, carefully crimp and solder the wires to each terminal, reconnect the terminals, reposition the cord protector, align and snap the casing back together, and replace the four screws. Plug it in and test for proper operation. Read more...

Outer Flange

$6.51

Fix Number: FIX10176005
Manufacturer Part Number: 5140005-33

This is an authentic manufacturer sourced replacement part, it is specially designed for use with angle grinders. It is the outer flange which is utilized to secure the grinding disk, please note the inner flange is sold separately. This high-quality hardware is made of durable metal and it is sold individually.

Craftsman Grinder Parts

Popular Craftsman Grinder Parts

Installation Instructions

Installation Instructions

Craftsman Grinder Appliance Types

Related Craftsman Grinder Parts

Popular Craftsman Grinder Models

Craftsman Grinder Parts

Start With Your Model Number

Popular Craftsman Grinder Parts

Installation Instructions

Installation Instructions

Craftsman Grinder Appliance Types

Related Craftsman Grinder Parts

Popular Craftsman Grinder Models