Grinder Parts

Watch the install video

Brush

$5.19

★★★★★

1 Review

Fix Number: FIX10188358
Manufacturer Part Number: N097696

Carbon Brush Set

$14.14

Fix Number: FIX10156653
Manufacturer Part Number: CB340

Set of 2 Carbon Brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a Makita retail box. rnThis brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that’s operating intermittently. • New brushes can restore a motor’s electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Watch the install video

Brush

$8.33

★★★★★

2 Reviews

Fix Number: FIX10183735
Manufacturer Part Number: 650916-01

Sold Individually This motor brush is for angle grinders. The motor brush transfers electric current to the spinning armature in the motor. Unplug the angle grinder before installing this part. Wear work gloves to protect your hands.

Installation Instructions

Pam from BENBROOK, TX

Worn brush

Honestly I Utubed it, cause it was the first time I've done it and wanted to make sure I did it right, super easy. Read more...

Watch the install video

Hex Hole Flange

$6.17

Fix Number: FIX10188627
Manufacturer Part Number: N134467

Carbon Brush Set

$10.85

Fix Number: FIX10156641
Manufacturer Part Number: CB154

This motor brush set is for power tools. Motor brush set transfers electric current to the spinning armature in the motor. The set includes both motor brushes.

Watch the install video

Power Cord

$17.56

★★★★★

1 Review

Fix Number: FIX10169875
Manufacturer Part Number: 330072-98

This power cord is used for power tools and some of the following tools: electric drills, reciprocating saws, jig saws, biscuit joiners, and routers. The power cord is made for double insulated tools and is a two-wire cord with two prongs, but it does not need a ground wire. If there are cuts in the cord insulation, intermittent power during operation, or damaged and bent prongs, then replacing the power cord will solve the problem. The tools needed for this repair are a Phillips screwdriver, small screwdriver, wire cutters/strippers, crimping tool, and terminal (ring or spade). Repair tip: During installation, remember that new cord wires must go correctly into wire terminals. Also, to avoid pinching when the tool case is put back into place, remember to route cord and wires in the right path.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

Watch the install video

Carbon Brush Set CB-325

$6.19

Fix Number: FIX10156652
Manufacturer Part Number: CB325

Watch the install video

Clamp Washer

$5.19

Fix Number: FIX10188483
Manufacturer Part Number: N115381

This is an OEM metal clamp washer for angle grinders. It is located on the spindle shaft and gives support to the grinding wheel. Most of our customers have found this repair very quick and easy. You will need a hex wrench to complete the installation.

Cordset

$18.83

★★★★★

1 Review

Fix Number: FIX11929697
Manufacturer Part Number: N353819

This is an original replacement part manufactured for use with DeWalt angle grinders. This two wire cord had a rubberized jacket, and the wires have crimped terminals to make installation easier. The cordset is available individually.

Carbon Brush Set CB-303

$10.85

Fix Number: FIX10156649
Manufacturer Part Number: CB303

The carbon brush is used on a variety of tools and are commonly replaced because they wear out easily with time and use. If your brush is worn out it can affect the motor from working properly and reduce electric braking. Tip: to check if the brush is worn out, inspect the wire lead for cracks, burns and other damage. Refer to the diagram provided by the manufacturer for further installation instructions. *Please note: This part is sold individually. This assembly includes a carbon brush, spring and holder.

Popular Grinder Parts

Installation Instructions

Installation Instructions

Brands

Related Pages

Popular Grinder Models

Grinder Parts

Start With Your Model Number

Popular Grinder Parts

Installation Instructions

Installation Instructions

Brands

Related Pages

Popular Grinder Models