OEM Craftsman Sander Polisher Parts & Accessories

Dust Seal

$12.28

Fix Number: FIX10166528
Manufacturer Part Number: 151553-00

Genuine OEM replacement part, this item is sold individually. The 151553-00 Dust Seal/Brake is a dual propose part. It is a Dust Seal to help prevent dust and debris from entering the motor assembly. It also acts as a Brake to keep the sanding pad at lower RPM so the sander will work properly. It is a good idea to replace this part when you are replacing the sanding pad.

5 DISC ASSEMBLY W/ H&L

$8.75

★★★★★

1 Review

Fix Number: FIX18693700
Manufacturer Part Number: 300527002

This is an authentic 5-inch sanding pad assembly for a sander. It provides support for hook and loop sandpaper. This part is prone to deteriorate, especially if too much pressure is applied to the sander while in use. This creates too much heat, which wears the sanding pad much quicker. For this simple repair, unfasten the four screws attaching the pad to the sander, and fasten the new pad in its place. This OEM pad assembly is sold individually.

Installation Instructions

Michael from EL PASO, TX

replaced hook and loop pad

Removed the 4 screws and replaced. Read more...

Retainer ( Includes Self Tappi

$6.51

Fix Number: FIX10168760
Manufacturer Part Number: 286181-00

This item is an authentic, OEM sourced replacement part that is intended to be used with random orbital sanders from DeWalt, Black & Decker, and Porter Cable. The retainer is used to support the bearing between the fan and the sanding pad. This item is available as an individual replacement part.

Switch Cover

$6.51

Fix Number: FIX10166043
Manufacturer Part Number: 144983-07

This is a Genuine Manufacturer Sourced replacement part used on a variety of Sanders. This part is made out of Plastic and it is Sold Individually. This part is secured over Switch providing protection from the dust.

WASHER 21/64X5/8X1/32

$6.51

Fix Number: FIX18701297
Manufacturer Part Number: 805553-2

This replacement washer is a genuine OEM supplied item. It is sourced from original equipment manufacturer for use with Ridgid belt sanders. Washer helps to distribute the pressure evenly between two connected pieces. Please make sure to check appropriate diagrams for correct location and use of this hardware. This part is made from durable metal and it is sold individually.

Hook And Loop Backing Pad

$12.06

★★★★★

2 Reviews

Fix Number: FIX10075791
Manufacturer Part Number: 030157001018

This sander pad is compatible with the Ryobi random orbit sander listed below. It is genuine Ryobi replacement part. The pad features a durable foam body attached to a hard plastic backing plate. It is a five inch diameter pad with a hook-and-loop style underside for use with Hook and Loop type sandpaper. This pad has eight vacuum holes. Hook and Loop sandpaper has become very popular over the past few years, because of the ease of changing sandpaper grits when needed.

Bearing Retainer

$6.51

Fix Number: FIX10180805
Manufacturer Part Number: 603637-00

Genuine OEM replacement part designed for certain Random Orbit Sanders. This item is made out of Metal and it is Sold Individually. This is the bottom Bearing Retainer that keeps the bearing in place. It is attached to the fan with 3 screws which are Sold Separately.

Watch the install video

BRUSH

$11.19

Fix Number: FIX12410247
Manufacturer Part Number: 445861-25

(Sold Individually) This motor brush is for grinders. The motor brush transfers electric current to the spinning armature in the motor. Unplug the grinder before installing this part. Wear work gloves to protect your hands.

Watch the install video

Electric Drill Cord Protector

$9.74

Fix Number: FIX10169655
Manufacturer Part Number: 330005-01

This is a cord protector, but it is also called a strain relief, and it is used with multiple power tools. This part is made of firm rubber to protect the cords from being pulled out or exposed, which would be a safety hazard. Over time the strain relief can develop cracks and break into pieces. This part is black and 4 inches long. The smallest end has a diameter of 0.5 inches. When completing this repair tuck in all wires to avoid pinching.

Installation Instructions

John from SPRINGVILLE, CA

Old worn cord shorting out.

Remove the four screws and carefully separate the casing at the trigger handle. Disconnect the terminals by lifting the switch slightly, just enough to remove the inside terminal. Needle nose pliers will make it easier to remove the terminals. Slip the cord protector over the new cord. Cut the two new wires to the proper length. I measured the old connectors for proper fit. Strip a half inch off the insulation, carefully crimp and solder the wires to each terminal, reconnect the terminals, reposition the cord protector, align and snap the casing back together, and replace the four screws. Plug it in and test for proper operation. Read more...

Brush Spring

$6.51

★★★★★

1 Review

Fix Number: FIX10173420
Manufacturer Part Number: 445860-00

This is a brush spring and it is used in a variety of power tools. The spring applies force to the motor brush inside the motor. This will keep the brush tight along the armature. If the brush has worn down it will create heat, and the spring will lose tension. If this happens, both parts will have to be replaced.

Craftsman Sander Polisher Parts

Popular Craftsman Sander Polisher Parts

Installation Instructions

Installation Instructions

Craftsman Sander Polisher Appliance Types

Related Craftsman Sander Polisher Parts

Popular Craftsman Sander Polisher Models

Craftsman Sander Polisher Parts

Start With Your Model Number

Popular Craftsman Sander Polisher Parts

Installation Instructions

Installation Instructions

Craftsman Sander Polisher Appliance Types

Related Craftsman Sander Polisher Parts

Popular Craftsman Sander Polisher Models