Sander Polisher Parts

BRUSH

$21.66

Fix Number: FIX18993190
Manufacturer Part Number: N031652

This brush is a genuine Porter-Cable replacement part, not generic. As pictured, this brush is ready to install and includes carbon brush, wire lead, and spring. This item is sold individually. Over time, brushes will wear down and eventually require replacement. This brush will fit the models listed in the 'Compatibility' section below. It is not guaranteed to fit any other power tool models. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor’s electric braking Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

Carbon Brush Set

$24.97

Fix Number: FIX10156653
Manufacturer Part Number: CB340

Set of 2 Carbon Brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a Makita retail box. rnThis brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that’s operating intermittently. • New brushes can restore a motor’s electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Carbon Brush Assembly

$6.51

Fix Number: FIX10122192
Manufacturer Part Number: 22-18-0680

This carbon brush is used on a variety of cordless tools and tools. *Please note: This part is sold individually. Carbon brushes are commonly replaced because they wear out easily with friction. If your brush is worn out it can cause disruption in the functioning of the motor and reduce electric braking. If you notice cracks, burns and other damage on wire lead, then it is best to replace it to restore the motor and its functions. Refer to the manual provided by the manufacturer for further installation instructions.

PAD

$39.83

Fix Number: FIX12398026
Manufacturer Part Number: 151281-08

The 151281-08 Pad is used to hold 5 inch Hook and Loop sandpaper with 8 vacuum holes. Over the past few years the popularity of Hook and Loop paper has grown because of the ease of changing sandpaper when needed. Over that of the PSA (Pressure Sensitive Sandpaper) Applying too much pressure on the sander may cause premature wear on the Hook and Loop pad. When a pad needs to be replaced, simply remove the three screws that hold the pad to the sander, then replace it with a new pad.

Watch the install video

BRUSH

$12.35

Fix Number: FIX12410247
Manufacturer Part Number: 445861-25

(Sold Individually) This motor brush is for grinders. The motor brush transfers electric current to the spinning armature in the motor. Unplug the grinder before installing this part. Wear work gloves to protect your hands.

Dust Nozzle

$7.31

Fix Number: FIX10150236
Manufacturer Part Number: 416497-7

This is a dust nozzle for a belt sander, and it is sold individually. Keep in mind that the O-ring that secures the nozzle into the housing is sold separately. Your belt sander dust bag attaches to this dust nozzle. Its main function is to allow the bag to pivot so you can position it as needed while you are sanding. This plastic nozzle is clamped between the sanders housing and is generally only damaged if the sander is dropped by accident. This is a quick and simple repair that will require you to remove the side cover for access to the part.

Hook And Loop Sander Pad

$10.88

★★★★★

1 Review

Fix Number: FIX11878741
Manufacturer Part Number: 51-36-7100

This is a genuinely sourced hook and loop sander pad for your sander. It is intended for 5-inch discs, and has 8 dust collection holes, which work alongside the dust bag to contain debris. Be careful not to apply too much tension on the sander as this can lead to early wear on the hook and loop sander pad. When replacing a pad, remove the four screws that secure the pad to the sander and replace it with your new pad.

Sander Carbon Brush Set

$11.51

★★★★★

1 Review

Fix Number: FIX11929758
Manufacturer Part Number: N398321

This motor brush set is for power tools. The motor brush set transfers electric current to the spinning armature in the motor. The set includes both motor brushes. Unplug the power tool before installing this part.

Watch the install video

Power Cord

$27.56

★★★★★

1 Review

Fix Number: FIX10169875
Manufacturer Part Number: 330072-98

This power cord is used for power tools and some of the following tools: electric drills, reciprocating saws, jig saws, biscuit joiners, and routers. The power cord is made for double insulated tools and is a two-wire cord with two prongs, but it does not need a ground wire. If there are cuts in the cord insulation, intermittent power during operation, or damaged and bent prongs, then replacing the power cord will solve the problem. The tools needed for this repair are a Phillips screwdriver, small screwdriver, wire cutters/strippers, crimping tool, and terminal (ring or spade). Repair tip: During installation, remember that new cord wires must go correctly into wire terminals. Also, to avoid pinching when the tool case is put back into place, remember to route cord and wires in the right path.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

Carbon Brush Set

$19.19

Fix Number: FIX10156649
Manufacturer Part Number: CB303

The carbon brush is used on a variety of tools and are commonly replaced because they wear out easily with time and use. If your brush is worn out it can affect the motor from working properly and reduce electric braking. Tip: to check if the brush is worn out, inspect the wire lead for cracks, burns and other damage. Refer to the diagram provided by the manufacturer for further installation instructions. *Please note: This part is sold individually. This assembly includes a carbon brush, spring and holder.

Popular Sander Polisher Parts

Installation Instructions

Sander Polisher Brands

Related Sander Polisher Parts

Popular Sander Polisher Models

Sander Polisher Parts

Start With Your Model Number

Popular Sander Polisher Parts

Installation Instructions

Sander Polisher Brands

Related Sander Polisher Parts

Popular Sander Polisher Models