OEM Delta Sander Polisher Parts & Accessories

Hex Jam Nut

$6.51

Fix Number: FIX10327792
Manufacturer Part Number: 902010201227S

This item has been sourced from the original manufacturer to be used with drill presses, band saws, sanders, bench grinders, lathes, radial arm saws, and finishing machines from Delta and Black & Decker. The metal nut is used with several different types of tools and the application of the nut can vary based on the model of the equipment.

Gear

$54.95

Fix Number: FIX10320166
Manufacturer Part Number: 1347788

It is a genuine OEM component which is designed for Delta sanders. This is the gear that attaches to the camshaft. It helps to drive the spindle assembly. Unfortunately, over time it may wear out or get damaged eventually requiring a replacement to ensure your equipment operates properly. One durable plastic gear is included. To ensure the proper repair procedure, refer to the appropriate diagrams of your model. To perform this repair a screwdriver and a wrench set will be necessary to take the housing apart.

Hex Nut

$18.02

Fix Number: FIX10327835
Manufacturer Part Number: 902012012571S

This lock nut is sourced directly from an original manufacturer. It is generally used on Delta power tools. The common purpose of this nut is to secure blade to the unit. It has right hand threads and it is sold individually. You would need a wrench to remove or install this nut.

Ball Bearing

$8.28

Fix Number: FIX10180907
Manufacturer Part Number: 605040-15

Genuine OEM sourced replacement part used on a variety of power tools. Ball bearings are used to reduce friction between rotating parts. Bearings experience constant wear when the tool is in operation, because of this they need to be periodically checked and replaced if needed. This part is made out of metal and it is sold individually. Included in part number 381004-00 spindle assembly.

BELT

$8.42

Fix Number: FIX18981445
Manufacturer Part Number: 491937-00

This is a manufacturer-approved belt for a sander, and it is sold as an individual part. This rubber belt is 16-inches by 3/8-inches and has 80 teeth. It is located underneath the belt cover and is placed around the segmented drive pulley and driven pulley. It is what drives the sanding belt and sanding disk. It is common for the cogs to wear down over time, the belt can also crack, break, and start to fray along the edges. If the sander is overloaded this can speed up the wear of the belt. For this repair you will need to remove the belt cover, and then you will line up the belt onto the pulleys.

Washer

$6.51

Fix Number: FIX10176170
Manufacturer Part Number: 5140010-69

This is a washer for your power tools. It is made of steel, and is sold individually. The washer is needed to evenly divide pressure and weight between two connected parts. It has various applications, depending on your equipment.

Bearing

$26.35

Fix Number: FIX10329668
Manufacturer Part Number: 920040105355

This is an authentic Delta replacement part. The bearing is designed by the manufacturer for use in power tools such as sanders, planers, and jointers. This part is made of metal, and is generally used to allow components to spin easily. It may be found in various locations in the machine, depending on model. Please be aware that there are different bearings used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You may require a screwdriver or wrench when replacing this part. This item is sold individually.

Table Saw Switch

$43.95

★★★★★

10 Reviews

Fix Number: FIX10325609
Manufacturer Part Number: 489105-00

This Switch is an OEM approved replacement part for various tools and models manufactured by Delta, Black and Decker, and Porter Cable. For full compatibility, please see the "Model Cross Reference List" below. This Switch has four terminals, a removable safety key, and a compact design for easy installation. The purpose of the switch is to turn the device on/off, as well as playing a role in electric breaking by momentarily reversing electrical polarity. Due to the mechanical internals of switches, they tend to degrade and wear out over time, making them a commonly replaced part in power tools. Common symptoms of a broken switch include: the device has completely stopped functioning, it will not turn on, and turning off intermittently during use. Each Switch is sold individually, and may also be referred to as a Rocker Switch.

Installation Instructions

keith from EMPORIA, KS

Power switch would not turn saw off

unplugged power cord.
removed the nut holding the power switch assembly on the saw.
removed 3 screws from the back cover.
removed the 2 white wires and 2 black wires from the switch terminal post. pay attention to wire color on each post.
removed old switch from the bracket by squeezing the sides of the old switch to remove the switch from the bracket.
inserted the new switch in place in the opening.
re attached the wires to the spade terminal on the switch using the 4 terminals. black on the 2 posts top and bottom on one side and the other side white on the top and bottom.
re attach the switch assembly to the table saw
test operation Read more...

Watch the install video

Ball Bearing

$17.55

★★★★★

1 Review

Fix Number: FIX10169632
Manufacturer Part Number: 330003-64

This is a ball bearing for your power tools. It is used in a variety of machines for rotary motion. The bearings support your tools by lowering the friction, which allows easy rotation of moving parts. Depending on how often you use your tool the bearings are a commonly replaced part. This is because they will experience most of the pressure, heat, and vibrations.

Installation Instructions

Michael from NEW BERLIN, WI

Bad bearing on brush end of Bucksaw motor

remove the brush cover on the end oppisite blade, unplug brush and remove bronze brusholder, if not replacing brushes , mark them for left and right. In my case the bearing had seized to the armature shaft much tighter than its normal shrink fit, so a bearing puller was needed, once the bearing is off, clean up shaft , heat bearing to about 200 deg F and blast end of shaft with cyrofreeze -60 F quickly drop bearing onto shaft and with very little effort it should slide on and bottom out on shaft. work quickly the shrink fit only lasts a few seconds. the trick is to heat bearing but not get it too warm and distort the plastic bearing cover. reinstall brush cap and old or new brushes. these old bucksaws are great for siding jobs , problem is only thing still available is the bearings and brushes. I think this saw is 35-40 years old , maybe I can get another 10 years out of it and by then I will be too old to lift it. Read more...

Key

$11.79

Fix Number: FIX10318424
Manufacturer Part Number: 1343758

This safety key fits multiple hardware tools and is inserted into the switch to make it possible for your machine to turn on and operate. Tip: you can remove the key to prevent unauthorized use of the machine. For installation instructions refer to the diagram provided by the manufacturer.

Delta Sander Polisher Parts

Popular Delta Sander Polisher Parts

Installation Instructions

Installation Instructions

Delta Sander Polisher Appliance Types

Related Delta Sander Polisher Parts

Popular Delta Sander Polisher Models

Delta Sander Polisher Parts

Start With Your Model Number

Popular Delta Sander Polisher Parts

Installation Instructions

Installation Instructions

Delta Sander Polisher Appliance Types

Related Delta Sander Polisher Parts

Popular Delta Sander Polisher Models