Delta Parts

★★★★★

★★★★★

6 Reviews

Fix Number

FIX18993125

Manufacturer Part Number

N008792

★★★★★

★★★★★

2 Reviews

Fix Number

FIX10323790

Manufacturer Part Number

426020630001S

This is a table insert plate for your saw. It is attached to the table, and provides access to the blade. A table insert protects the rest of the unit by preventing wood from getting jammed under the blade during cutting. The slit in the insert plate allows for the saw blade to run smoothly. Before installing this part, unplug your saw.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX12522478

Manufacturer Part Number

N044359

This is a tube seal used with various power tools. The seal prevents air from leaking out of your equipment. It is placed on the outlet tube, and connected to the head of the compressor. Note that this part is sold individually. If you are having trouble with your air pressure, you may need to replace this part.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX12517182

Manufacturer Part Number

N017592SV

This is a valve plate for your compressor or generator. This part controls the air flow into the pump. When the air is pumped by the piston, it passes through the valve plate and into the compressor tank. The most common sign of a damaged valve is if your pressure is not building up in the tank. The reeds on the valve plate are usually the first thing to wear out. If you notice visible damage on the reeds you will need to replace this part. This valve includes the plate, and the lower gasket. The head gasket is sold individually.

Fix Number

FIX10176277

Manufacturer Part Number

5140011-85

This is a single carbon brush with a spring. Carbon brushes are what supply electricity to the armature. They are known to wear due to constant rubbing against the commutator, so it should not be a concern if they are in need of a replacement. They should be inspected regularly, especially if your power tool is not functioning properly. A worn brush can cause excessive sparks, however a damaged armature can also cause sparks, so you will need to inspect both parts. This is a simple repair that should only take a few minutes. You will need to remove the brush caps, and then align the new carbon brush in the holder with the tabs. You will need a screwdriver to secure the cap.

★★★★★

★★★★★

3 Reviews

Fix Number

FIX12508562

Manufacturer Part Number

N286039

This is a single OEM drain valve for an air compressor. A drain valve is a small device that is usually located at the bottom of the compressor air receiver. The drain valve can be opened or closed, and this allows water to exit the tank. Water builds up if air is left in the tank for an extended period of time, and if left for too long, it can start to rust out the inside of the tank and the drain valve can become clogged with rust or start to corrode. You should be draining the tank each time you use your air compressor to stop this from happening. This is a very quick and simple repair. Use a wrench to remove the old drain valve, and thread the new one into place by hand.

Fix Number

FIX12504961

Manufacturer Part Number

874582

Genuine OEM replacement part, this item is sold individually. The 874582 Clamp Knob is used to tighten the bases of all of the Routers shown below. It is used with part number 695526 Screw, to clamp the Router Motor in the base for the desired height of the motor.

Fix Number

FIX18987507

Manufacturer Part Number

884443

This is a protective cover, which protects the air inlet coupler. This OEM part is sold independently. It is needed to keep dust and debris from making its way inside the nailer or stapler and contaminating the parts inside the tool. The cover should be in place over the coupling when the tool is not in use. These covers can start to break down over time, and will need to be replaced to ensure your tool is properly protected.

Fix Number

FIX12513333

Manufacturer Part Number

CAC-1206-1

This high-quality OEM metal hose clamp is a part found in air compressors, and is sold individually. This part can be used on multiple parts on the air compressor, so the exact location, and repair may differ. In general, it is used to clamp hoses. For this repair, begin by draining the air out of the tank to remove the pressure placed on the components.

★★★★★

★★★★★

10 Reviews

Fix Number

FIX10325609

Manufacturer Part Number

489105-00

This Switch is an OEM approved replacement part for various tools and models manufactured by Delta, Black and Decker, and Porter Cable. For full compatibility, please see the "Model Cross Reference List" below. This Switch has four terminals, a removable safety key, and a compact design for easy installation. The purpose of the switch is to turn the device on/off, as well as playing a role in electric breaking by momentarily reversing electrical polarity. Due to the mechanical internals of switches, they tend to degrade and wear out over time, making them a commonly replaced part in power tools. Common symptoms of a broken switch include: the device has completely stopped functioning, it will not turn on, and turning off intermittently during use. Each Switch is sold individually, and may also be referred to as a Rocker Switch.